Navigator Table Of Contents COVER 1 SAFETY PRECAUTIONS 1.1 GENERAL GUIDELINES 1.1.1 LEAKAGE CURRENT COLD CHECK 1.1.2 LEAKAGE CURRENT HOT CHECK (See Figure 1 .) 2 PREVENTION OF ELECTRO STATIC DISCHARGE (ESD) TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES 3 Precaution of Laser Diode 4 About lead free solder (PbF) 5 General Description 5.1 Operating instructions...
Page 2
Navigator 8.3 Clamp Plate Unit 8.4 Tray 8.5 Traverse Block 8.6 Traverse Gear 8.7 Optical Pickup Unit 8.7.1 Precautions in optical pickup replacement 8.7.2 Disassembling the Optical Pickup Unit 8.7.3 Cautions to Be Taken When Replacing the Optical Pickup 8.8 Disassembling the Middle Chassis 8.9 Disassembling the Traverse Gear A/...
Page 3
Navigator 11.4.1 Optical pickup tilt adjustment 11.4.1.1 Adjustment procedure 11.4.1.2 Important points 11.4.1.3 Check after adjustment 11.4.1.4 Procedure for screw lock 12 Abbreviations 13 VOLTAGE CHART 13.1 POWER SUPPLY P.C.B. 13.2 MAIN P.C.B. 13.3 OPERATION P.C.B. 14 BLOCK DIAGRAM 14.1 OVERALL BLOCK DIAGRAM 14.2 POWER SUPPLY BLOCK DIAGRAM (DVD-S35GCS/GCU/GC/GCA/GD/EE/GN/PL/PX/PLA) 14.3 POWER SUPPLY BLOCK DIAGRAM (DVD-S35PLA) 14.4 SERVO BLOCK DIAGRAM...
Page 4
Navigator 17.1 POWER SUPPLY P.C.B. (DVD-S35GCS/GCU/GC/GCA/GD/PL/PX) 17.2 POWER SUPPLY P..B. (DVD-S35EE/GN) 17.3 POWER SUPPLY P.C.B. (DVD-S35PLA) 17.4 MAIN P.C.B. (1/2) (COMPONENT SIDE) (DVD-S35GCS/GCU/GC/GCA/GD/EE/GN/PL/PLA) 17.5 MAIN P.C.B. (2/2) (FOIL SIDE) (DVD-S35GCS/GCU/GC/GCA/GD/EE/GN/PL/PLA) 17.6 MAIN P.C.B. ADDRESS INFORMATION 17.7 MAIN P.C.B. (1/2) (COMPONENT SIDE) (DVD-S35PX) 17.8 MAIN P.C.B.
Page 5
TOP NEXT ORDER NO.CHM0306017C0 DVD Player DVD-S35EE DVD-S35GN DVD-S35PL DVD-S35PLA DVD-S35PX DVD-S35GCS DVD-S35GCU DVD-S35GC DVD-S35GCA DVD-S35GD DL1S Mechanism Series Colour (S).......Silver Type (K).......Black Type (S35EE Only) Specifications Power supply: AC120 V, 60 Hz (DVD-S35PLA only) AC220-240V, 50Hz (DVD-S35EE/GN only) AC110-240V, 50/60Hz...
Page 6
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0000000000.html Mass: 2.1 kg (4.7 lb.) Signal system: NTSC (DVD-S35PX only) PAL625/50, PAL525/60, NTSC (except DVD-S35PX) Operating temperature range: +5 to+35°C (+41 to 95°F) Operating humidity range: 5 to 90% RH (no condensation) Region number: Region No.1 (DVD-S35PX only) Region No.2 (DVD-S35GC/GCA)
Page 7
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0000000000.html Component video output (480P/480I) (DVD-S35PXonly) (NTSC:480p/480I,PAL:576I) (exceptDVD-S35PX) Y output level: 1 Vp-p (75Ω) PB output lebel: 0.7 Vp-p (75Ω) PR output level 0.7 Vp-p (75Ω) Output terminal: Pin jack (Y:green, PB :blue, PR :red) Number of terminal: 1 system Audio output: Output level:...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0100000000x.html 1 SAFETY PRECAUTIONS TOP PREVIOUS NEXT 1.1 GENERAL GUIDELINES 1.1.1 LEAKAGE CURRENT COLD CHECK 1.1.2 LEAKAGE CURRENT HOT CHECK (See Figure 1 .) TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0100000000x.html03.10.2007 22:43:17...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0101000000.html 1.1 GENERAL GUIDELINES TOP PREVIOUS NEXT 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0101010000.html 1.1.1 LEAKAGE CURRENT COLD CHECK TOP PREVIOUS NEXT 1. Unplug the AC cord and connect a jumper between the two prongs on the plug. 2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads, connectors, control shafts, etc.
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0101020000.html 1.1.2 LEAKAGE CURRENT HOT CHECK (See Figure 1 TOP PREVIOUS NEXT 1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check. 2. Connect a 1.5kΩ, 10 watts resistor, in parallel with a 0.15μF capacitors, between each exposed metallic part on the set and a good earth ground such as a water pipe, as shown in Figure 1 3.
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0200000000x.html 2 PREVENTION OF ELECTRO STATIC DISCHARGE (ESD) TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES TOP PREVIOUS NEXT Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistorsand semiconductor"chip"...
Page 14
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0200000000x.html Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise hamless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient todamagean ES device).
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0300000000x.html 3 Precaution of Laser Diode TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0300000000x.html (1 of 2)03.10.2007 22:43:53...
Page 16
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0300000000x.html TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0300000000x.html (2 of 2)03.10.2007 22:43:53...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0400000000x.html 4 About lead free solder (PbF) TOP PREVIOUS NEXT Caution: Pb free solder has a higher melting point than standard solder; Typically thmelting point is 50 - 70°F (30 - 40°C) higher. Please use a high temperature soldering iron. In case of the soldering iron with temperature control,pleaseset it to 700 ±...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0500000000o.html 5 General Description TOP PREVIOUS NEXT 5.1 Operating instructions TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0500000000o.html03.10.2007 22:44:01...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0501000000.html 5.1 Operating instructions TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0501000000.html03.10.2007 22:44:05...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0600000000x.html 6 PREVENTION OF STATIC ELECTRICITY DISCHARGE TOP PREVIOUS NEXT The laser diode in the traverse unit (optical pickup) may brake down due to static electricity of clothes or human body. Use due caution to electrostatic breakdown when servicing and handling the laser diode. 6.1 Grounding for electrostatic breakdown prevention 6.1.1 Worktable grounding 6.1.2 Human body grounding...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0601000000.html 6.1 Grounding for electrostatic breakdown prevention TOP PREVIOUS NEXT Some devices such as the DVD player use the optical pickup (laser diode) and the optical pickup will be damaged by static electricity in the working environment. Proceed servicing works under the working environment where grounding works is completed.
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0601010000.html 6.1.1 Worktable grounding TOP PREVIOUS NEXT 1. Put a conductive material (sheet) or iron sheet on the area where the optical pickup is placed, and ground the sheet. TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0601010000.html03.10.2007 22:44:37...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0601020000.html 6.1.2 Human body grounding TOP PREVIOUS NEXT 1. Use the anti-static wrist strap to discharge the static electricity form your body. TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0601020000.html03.10.2007 22:44:40...
Рабочий стол file:///C|/Documents and Settings/eDOK/ /DVD-S35xx/s0601030000.html 6.1.3 Handling of optical pickup TOP PREVIOUS NEXT 1. To keep the good quality of the optical pickup maintenance parts during transportation and before installation, the both ends of the laser diode are short-circuited. After replacing the parts with new ones, remove the short circuit accordingtothe correct procedure.
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0602000000.html 6.2 Handling Precautions for Traverse Unit (Optical Pickup) TOP PREVIOUS NEXT 1. Do not give a considerable shock to the traverse unit (optical pickup) as it has an extremely high- precise structure. 2. When replacing the optical pickup, install the flexible cable and cut its short land with a nipper. See the optical pickup replacement procedure in this Technical Guide.
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0700000000x.html 7 Disassembling the Casing and Checking P.C.B.s TOP PREVIOUS NEXT 7.1 Dissasembly Procedure 7.2 Casing Parts and P.C.B. Positions 7.3 Top Panel 7.4 Front Panel 7.5 Rear panel 7.6 Power supply P.C.B. 7.7 Main P.C.B. and Mechanism Unit 7.8 Motor P.C.B.
Page 28
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0701000000.html 7.1 Dissasembly Procedure TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0701000000.html03.10.2007 22:44:57...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0702000000.html 7.2 Casing Parts and P.C.B. Positions TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0702000000.html03.10.2007 22:45:08...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0703000000.html Top Panel TOP PREVIOUS NEXT 1. Unscrew the screws. TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0703000000.html03.10.2007 22:45:12...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0704000000.html 7.4 Front Panel TOP PREVIOUS NEXT 1. Pull the tray out of the mechanism unit. Remove the gear and install it onto a screwdriver to make a gear jig. 2. Insert the gear jig into the tray open/ close hole. 3.
Page 32
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0704000000.html 5. Unscrew the screws. 6. Remove the connector. 7. Release the tabs. 8. Remove the connector. file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0704000000.html (2 of 3)03.10.2007 22:45:16...
Page 33
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0704000000.html TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0704000000.html (3 of 3)03.10.2007 22:45:16...
Рабочий стол file:///C|/Documents and Settings/eDOK/ /DVD-S35xx/s0705000000.html 7.5 Rear panel TOP PREVIOUS NEXT 1. Unscrew the screws. 2. Release the tabs. TOP PREVIOUS NEXT Рабочий стол file:///C|/Documents and Settings/eDOK/ /DVD-S35xx/s0705000000.html03.10.2007 22:45:19...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0706000000.html 7.6 Power supply P.C.B. TOP PREVIOUS NEXT 1. Unscrew the screws. 2. Remove the connector. file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0706000000.html (1 of 2)03.10.2007 22:45:26...
Page 36
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0706000000.html TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0706000000.html (2 of 2)03.10.2007 22:45:26...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0707000000.html 7.7 Main P.C.B. and Mechanism Unit TOP PREVIOUS NEXT 1. Unscrew the screws. 2. Remove the connectors. 3. Pull out the Main P.C.B. and mechanism unit vertically. 4. Unscrew the screw. 5. Remove the connectors. file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0707000000.html (1 of 2)03.10.2007 22:45:29...
Page 38
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0707000000.html TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0707000000.html (2 of 2)03.10.2007 22:45:29...
Рабочий стол file:///C|/Documents and Settings/eDOK/ /DVD-S35xx/s0708000000.html 7.8 Motor P.C.B. TOP PREVIOUS NEXT 1. Unscrew the screw. 2. Remove the solders. 3. Remove the connector. TOP PREVIOUS NEXT Рабочий стол file:///C|/Documents and Settings/eDOK/ /DVD-S35xx/s0708000000.html03.10.2007 22:45:33...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0709000000.html 7.9 Operation (L) P.C.B. and Operation (R) P.C.B. TOP PREVIOUS NEXT 1. Unscrew the screws. TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0709000000.html03.10.2007 22:45:36...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0710000000.html 7.10 Service Position TOP PREVIOUS NEXT 7.10.1 Servicing position of the Main P.C.B. and the Operation P.C.B. 7.10.2 List of the Extension Cables TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0710000000.html03.10.2007 22:45:40...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0710010000.html 7.10.1 Servicing position of the Main P.C.B. and the Operation P.C.B. TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0710010000.html03.10.2007 22:45:45...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0710020000.html 7.10.2 List of the Extension Cables TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0710020000.html03.10.2007 22:45:48...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0800000000x.html 8 ASSEMBLING AND DISASSEMBLING THE MECHANISM UNIT TOP PREVIOUS NEXT 8.1 Disassembly Procedure 8.2 Motor P.C.B. 8.3 Clamp Plate Unit 8.4 Tray 8.5 Traverse Block 8.6 Traverse Gear 8.7 Optical Pickup Unit 8.7.1 Precautions in optical pickup replacement 8.7.2 Disassembling the Optical Pickup Unit 8.7.3 Cautions to Be Taken When Replacing the Optical Pickup 8.8 Disassembling the Middle Chassis...
Рабочий стол file:///C|/Documents and Settings/eDOK/ /DVD-S35xx/s0801000000.html 8.1 Disassembly Procedure TOP PREVIOUS NEXT TOP PREVIOUS NEXT Рабочий стол file:///C|/Documents and Settings/eDOK/ /DVD-S35xx/s0801000000.html03.10.2007 22:45:59...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0802000000.html 8.2 Motor P.C.B. TOP PREVIOUS NEXT 1. Unscrew the screw. 2. Remove the solders. 3. Remove the connector. TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0802000000.html03.10.2007 22:46:04...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0803000000.html 8.3 Clamp Plate Unit TOP PREVIOUS NEXT 1. Spread the stopper with hand to slide the tabs and remove the clamp plate unit. TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0803000000.html03.10.2007 22:46:08...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0804000000.html 8.4 Tray TOP PREVIOUS NEXT 1. Lift the tray. <Precautions in reassembling the tray> •Reassemble the tray so that it is in the backmost position. 1. Turn traverse gear until cam gear leaver comes to the lever adjusting position at the end of mechanical chassis unit.
Page 49
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0804000000.html 2. Check the position of convex phase on back of the tray, and that of concave phase on drive gear. A. Place the tray on the unit from rearward. file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0804000000.html (2 of 3)03.10.2007 22:46:11...
Page 50
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0804000000.html B. Inch the tray frontward until convex phase and concave phase mate. Caution: Make sure to mate convex phase and concave phase properly, so that the gap between turntable and tray becomes 5mm or less. TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0805000000.html 8.5 Traverse Block TOP PREVIOUS NEXT 1. Lift the traverse block while spreading the hook of the mechanical chassis unit. 2. Disengage the tabs from the holes of the mechanical chassis unit. <Precautions in reassembling the traverse block> •Take the following precautions when reassembling the traverse block.
Page 52
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0805000000.html TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0805000000.html (2 of 2)03.10.2007 22:46:16...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0806000000.html 8.6 Traverse Gear TOP PREVIOUS NEXT 1. Disengage the tabs from the traverse gear. 2. Remove the traverse gears B and C. TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0806000000.html03.10.2007 22:46:21...
Рабочий стол file:///C|/Documents and Settings/eDOK/ /DVD-S35xx/s0807000000.html 8.7 Optical Pickup Unit TOP PREVIOUS NEXT 1. Make the right turn the trigger lever. 2. Unscrew the screws. 3. Remove the spring holders and the springs. 4. Pull out the drive shaft and guide shaft. 8.7.1 Precautions in optical pickup replacement 8.7.2 Disassembling the Optical Pickup Unit 8.7.3 Cautions to Be Taken When Replacing the Optical Pickup...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0807010000.html 8.7.1 Precautions in optical pickup replacement TOP PREVIOUS NEXT The optical pickup can be damaged by static electricity from you body. Be sure to take static electricity countermeasures when working around the optical pickup. (Refer to the related page in this Manual about the countermeasures.) 1.
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0807020000.html 8.7.2 Disassembling the Optical Pickup Unit TOP PREVIOUS NEXT 1. Remove the 2 screws A and remove the TRV feed rack. 2. Remove the screw B and remove the Terminal FPC. 3. Remove the optical pickup. Fig.
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0807030000.html 8.7.3 Cautions to Be Taken When Replacing the Optical Pickup TOP PREVIOUS NEXT An antistatic flexible sheet (FPC) is connected with the new optical pickup. Replace the optical pickup according to the following procedure. 1. Install the Terminal FPC, TRV feed rack on the optical pickup. (See Fig.
Page 58
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0807030000.html Cautions to be taken when assembling the unit: Install the pickup unit so that it is located at the rear end of the guide shaft. 3. Cut the antistatic flexible sheet for the optical pickup unit. Fig.
Page 59
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0807030000.html TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0807030000.html (3 of 3)03.10.2007 22:46:39...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0808000000.html 8.8 Disassembling the Middle Chassis TOP PREVIOUS NEXT 1. Remove the holder pins. 2. Remove the tabs. 3. It lifts while pulling it in the direction of the arrow. TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0808000000.html03.10.2007 22:46:43...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0809000000.html 8.9 Disassembling the Traverse Gear A/ FG P.C.B. TOP PREVIOUS NEXT 1. Unscrew the screw. 2. Remove the traverse gear A. TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0809000000.html03.10.2007 22:46:47...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0810000000.html 8.10 Disassembling the Spindle Motor Unit TOP PREVIOUS NEXT 1. Remove the floating rubbers. TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0810000000.html03.10.2007 22:46:50...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0900000000x.html 9 Self-Diagnosis Function and Service Modes TOP PREVIOUS NEXT 9.1 Optical Pickup Breakdown Diagnosis 9.2 Service Mode Table 1 9.3 DVD Self Diagnostic Function-Error Code 9.4 Last Error Code saved during NO PLAY 9.5 Service mode table 2 9.6 Sales demonstration lock function 9.6.1 Setting 9.6.2 Cancellation...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0901000000.html 9.1 Optical Pickup Breakdown Diagnosis TOP PREVIOUS NEXT The optical pickup self-diagnosis function and tilt adjustment check function have been included in this unit. When repairing, use the following procedure for effective Self-diagnosis and tilt adjustment.Be sure to use the self-diagnosis functionbeforereplacing the optical pickup when "NO DISC"...
Page 65
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0901000000.html TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0901000000.html (2 of 2)03.10.2007 22:47:06...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0902000000.html 9.2 Service Mode Table 1 TOP PREVIOUS NEXT The service modes can be activated by pressing various button combination on the player and remote control unit. Player buttons Remote control unit buttons Application Note PAUSE Displaying the UHF display F_ _ _ Refer to section 9.3.
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0903000000.html 9.3 DVD Self Diagnostic Function-Error Code TOP PREVIOUS NEXT Error Error Content Additional error Defect 1 Defect 2 Defect 3 Defect 4 Code explanation U, H error Focus error Tray loading error Spindle servo error (Spindle servo, DV1 (IC3001) SP motor, CLV servo error) Traverse servo error...
Page 68
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0903000000.html F506 Invalid media Disc is flipped over, TOC DISC unreadable, incompatible (IC3001) (IC3001) (IC3001) disc ODC related F600 Access failure to Operation stopped management because navigation data (IC3001) (IC3001) (IC3001) information caused by is not accessible caused demodulation error by the demodulation defect...
Page 69
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0903000000.html F702 Message command Message is changed changes before it is sent as a reply to disc manager F880 Task number is not Message coming from a appropriate non-existing task F890 Sending message when Sending message to AV message is being sent task to AV task...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0904000000.html 9.4 Last Error Code saved during NO PLAY TOP PREVIOUS NEXT Error code Error Content System computer Setting task System computer internal error code F0BF 6) Cannot playback because PCND_NOPLAY PHYSICAL 0x50 DriveManager 0xDOBF physical layer is not recoginizable F0C0 8) DVD: Cannot playback because PCND_NOPLAY VIDEO 0x70...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0905000000.html 9.5 Service mode table 2 TOP PREVIOUS NEXT Pressing various button combinations on the player and remote control unit can activate the service modes. file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0905000000.html (1 of 3)03.10.2007 22:47:21...
Page 72
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0905000000.html file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0905000000.html (2 of 3)03.10.2007 22:47:21...
Page 73
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0905000000.html TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0905000000.html (3 of 3)03.10.2007 22:47:21...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0906000000.html 9.6 Sales demonstration lock function TOP PREVIOUS NEXT This function prevents discs from being lost when the unit is used for sales demonstrations by disabling the disc eject function. "LOCK" is displayed on the unit, and ordinary operation is disabled. 9.6.1 Setting 9.6.2 Cancellation TOP PREVIOUS NEXT...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0906010000.html 9.6.1 Setting TOP PREVIOUS NEXT The sales demonstration lock is set by simultaneously pressing STOP button on the player and POWER button on the remote control unit for 1 second or longer. TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0906010000.html03.10.2007 22:47:30...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0906020000.html 9.6.2 Cancellation TOP PREVIOUS NEXT The lock can be cancelled by the same procedure as used in setting. ("UNLOCK" is displayed on cancellation. Disconnecting the power cable from power outlet does not cancel the lock.) TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0907000000.html 9.7 Handling After Completing Repairs TOP PREVIOUS NEXT Use the following procedure after completing repairs. 9.7.1 Method 9.7.2 Precautions TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0907000000.html03.10.2007 22:47:37...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0907010000.html 9.7.1 Method TOP PREVIOUS NEXT Confirm that the power is turned on: 1. Press the "OPEN/CLOSE" button to close the tray. 2. Press the "POWER" button to turn off the power. 3. Disconnect the power plug from the outlet. TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0907020000.html 9.7.2 Precautions TOP PREVIOUS NEXT Do not disconnect the power plug from the outlet with the tray still open, then close the tray manually. TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s0907020000.html03.10.2007 22:47:43...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1000000000x.html 10 Servicw Precautions TOP PREVIOUS NEXT 10.1 Recovery after the dvd player is repaired 10.2 Firmware version-up of the DVD player TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1000000000x.html03.10.2007 22:47:51...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1001000000.html 10.1 Recovery after the dvd player is repaired TOP PREVIOUS NEXT When FROM or module P.C.B. is replaced, carry out the recovery processing to optimize the drive. Playback the recovery disk to process the recovery automatically. Recovery disc (Product number: RFKZD03R004) Performing recovery 1.
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1002000000.html 10.2 Firmware version-up of the DVD player TOP PREVIOUS NEXT The firmware of the DVD player may be renewed to improve the quality including operationability and playerbility to the substandard discs.processing to optimize the drive. The recovery disc has also firmware version-up. After version-up, recovery processing is executed automatically.
Page 83
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1002000000.html In such a case, replace the FROM and carry out the version-up again. TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1002000000.html (2 of 2)03.10.2007 22:48:01...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1100000000x.html 11 ADJUSTMENT PROCEDURES TOP PREVIOUS NEXT 11.1 Service Tools and Equipment 11.2 Important points in adjustment 11.2.1 Important points in optical adjustment 11.2.2 Important points in electrical adjustment 11.3 Storing and Handling Test Discs 11.4 Optical adjustment 11.4.1 Optical pickup tilt adjustment 11.4.1.1 Adjustment procedure 11.4.1.2 Important points...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1101000000.html 11.1 Service Tools and Equipment TOP PREVIOUS NEXT Application Name Number Tilt adjustment DVD test disc DVDT-S15 or DVDT-S01 Hex wrench Available on sales route. Inspection Extension cable (main P.C.B. to power supply P.C.B.) RFKZ0152 Extension cable (power supply P.C.B. to operation (R) P.C. VFK1732 Others Grease 1...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1102000000.html 11.2 Important points in adjustment TOP PREVIOUS NEXT 11.2.1 Important points in optical adjustment 11.2.2 Important points in electrical adjustment TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1102000000.html03.10.2007 22:48:12...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1102010000.html 11.2.1 Important points in optical adjustment TOP PREVIOUS NEXT Before starting optical adjustment, be sure to take anti-static measures. Optical pickup tilt adjustment is needed after replacement of the following components. 1. Optical pickup unit 2. Spindle motor unit 3.
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1102020000.html 11.2.2 Important points in electrical adjustment TOP PREVIOUS NEXT Follow the adjustment procedures described in this Manual. TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1102020000.html03.10.2007 22:48:20...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1103000000.html 11.3 Storing and Handling Test Discs TOP PREVIOUS NEXT Surface precision is vital for DVD test discs. Be sure to store and handle them carefully. 1. Do not place discs directly onto the workbench, etc., after use. 2.
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1104000000.html 11.4 Optical adjustment TOP PREVIOUS NEXT 11.4.1 Optical pickup tilt adjustment 11.4.1.1 Adjustment procedure 11.4.1.2 Important points 11.4.1.3 Check after adjustment 11.4.1.4 Procedure for screw lock TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1104000000.html03.10.2007 22:48:29...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1104010000.html 11.4.1 Optical pickup tilt adjustment TOP PREVIOUS NEXT Measurement point Adjustment point Mode Disc Tangential adjustment screw T01 (inner periphery) play DVDR-S15 or DVDT-S01 Tilt adjustment screw T43 (outer periphery) play Measuring equipment Adjustment value None (Main unit display for servicing is used.) Adjust to the minimum jitter value.
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1104010100.html 11.4.1.1 Adjustment procedure TOP PREVIOUS NEXT 1. While pressing PAUSE and OPEN/CLOSE buttons on the main unit, press "5" on the remote control unit. 2. Confirm that "J_xxx_yyy_zz" is shown on the front display. For your information: "yyy"...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1104010200.html 11.4.1.2 Important points TOP PREVIOUS NEXT 1. Make tangential adjustment first, and then make tilt adjustment. 2. Repeat adjusting two or three times to find the optimum point. 3. Finish the procedure with tilt adjustment. Jitter value depends on the model: If the jitter value changes like B, the optimum point is easy to find.
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1104010300.html 11.4.1.3 Check after adjustment TOP PREVIOUS NEXT Play test disc or any other disc to make sure there is no picture degradation in the inner, middle and outer peripheries, and no audio skipping. After adjustment is finished, lock each adjustment screw in position using screw lock.
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1104010400.html 11.4.1.4 Procedure for screw lock TOP PREVIOUS NEXT 1. After adjustment, remove top cover, tray, clamper base and traverse unit in this sequence. 2. Lay the traverse unit upside down, and fix adjustment screw with screw lock. 3.
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1200000000x.html 12 Abbreviations TOP PREVIOUS NEXT INITIAL/LOGO ABBREVIATIONS A A0~UP ADDRESS ACLK AUDIO CLOCK AD0~UP ADDRESS BUS ADATA AUDIO PES PACKET DATA ADDRESS LATCH ENABLE AMUTE AUDIO MUTE AREQ AUDIO PES PACKET REQUEST AUDIO RF SERVO AMP INVERTED INPUT SERVOAMPOUTPUT ASYNC AUDIO WORD DISTINCTION SYNC...
Page 97
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1200000000x.html D DACCK D/A CONVERTER CLOCK DEEMP DEEMPHASIS BIT ON/OFF DEMPH DEEMPHASIS SWITCHING DIG0~UP FL DIGIT OUTPUT DATA INPUT DMSRCK DM SERIAL DATA READ CLOCK DMUTE DIGITAL MUTE CONTROL DROPOUT DOUT0~UP DATAOUTPUT DATA SLICE RF (BIAS) DRPOUT DROP OUT SIGNAL DREQ DATA REQUEST...
Page 98
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1200000000x.html M MA0~UP MEMORY ADDRESS MEMORY CLOCK MCKI MEMORY CLOCK INPUT MCLK MEMORY SERIAL COMMAND CLOCK MDATA MEMORY SERIAL COMMAND DATA MDQ0~UP MEMORY DATA INPUT/OUTPUT MDQM MEMORY DATA I/O MASK MEMORYSERIALCOMMAND LOAD MPEG MOVING PICTURE EXPERTS GROUP O ODC OPTICAL DISC CONTROLLER OFTR...
Page 99
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1200000000x.html SQCX SUBCODEQ DATA READ CLOCK SRDATA SERIAL DATA SRMADR SRAM ADDRESS BUS SRMDT0~7 SRAM DATA BUS 0~7 START/STOP STAT STATUS STCLK STREAM DATA CLOCK STD0~UP STREAM DATA STENABLE STREAM DATA INPUT ENABLE STSEL STREAM DATA POLARITY SELECT STVALID STREAMDATAVALIDITY SUBC...
Page 100
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1200000000x.html X´ TAL XALE X ADDRESS LATCH ENABLE XAREQ X AUDIO DATA REQUEST XCDROM X CD ROM CHIP SELECT X CHIP SELECT XCSYNC X COMPOSITE SYNC X DATA STROBE XHSYNCO X HORIZONTAL SYNC OUTPUT XHINT XHINTERRUPTREQUEST X´ TAL OSCILLATOR INPUT XINT X INTERRUPT X MEMORY WRITE ENABLE...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1300000000x.html 13 VOLTAGE CHART TOP PREVIOUS NEXT Note: Indicated voltage values are the atandard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard. Therefore, there may exist some errors in the voltage values, depending on theinternalimpedance of the DC circuit tester. 13.1 POWER SUPPLY P.C.B.
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1301000000.html 13.1 POWER SUPPLY P.C.B. TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1301000000.html03.10.2007 22:49:09...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1302000000.html 13.2 MAIN P.C.B. TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1302000000.html03.10.2007 22:49:18...
Page 105
IC2501 Ref No. MODE STOP PLAY IC2501 Ref No. MODE STOP PLAY IC3001 Ref No. MODE STOP PLAY IC3001 Ref No. MODE STOP PLAY Ref No. IC3001 MODE STOP PLAY IC3001 Ref No. MODE STOP PLAY IC3001 Ref No. MODE STOP PLAY IC3001...
Page 106
Ref No. IC3501 MODE STOP PLAY IC3501 Ref No. MODE STOP PLAY IC4201 Ref No. MODE STOP PLAY IC4311 IC4491 IC6201 Ref No. MODE STOP -9.3 14.3 PLAY -9.1 13.0 IC6251 Ref No. MODE STOP PLAY IC6301 Ref No. MODE STOP PLAY Ref No.
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1303000000.html 13.3 OPERATION P.C.B. TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1303000000.html03.10.2007 22:49:29...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1400000000b.html 14 BLOCK DIAGRAM TOP PREVIOUS NEXT 14.1 OVERALL BLOCK DIAGRAM 14.2 POWER SUPPLY BLOCK DIAGRAM (DVD-S35GCS/GCU/GC/GCA/GD/EE/GN/PL/PX/PLA) 14.3 POWER SUPPLY BLOCK DIAGRAM (DVD-S35PLA) 14.4 SERVO BLOCK DIAGRAM 14.5 VIDEO BLOCK DIAGRAM 14.6 AUDIO BLOCK DIAGRAM TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1401000000.html 14.1 OVERALL BLOCK DIAGRAM TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1401000000.html03.10.2007 22:49:45...
Page 111
MECHANISM UNIT MAIN P.C.B. IC3001 IC4201 MIXL OPTICAL AUDIO PICK UP UNIT CONVERTER MIXR IC2501 SPINDLE MOTOR DIGITAL MOTOR AUDIO OUT DRIVE (OPTICAL) TRAVERSE IC6301 MOTOR DECODER (DV1) 16Mbit FLASH OPERATION (R) P.C.B. IC6001 IC3501 S-VIDEO OUT IC6351 VIDEO OUT VIDEO 16Kbit DRIVER...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1402000000.html 14.2 POWER SUPPLY BLOCK DIAGRAM (DVD- S35GCS/GCU/GC/GCA/GD/EE/GN/PL/PX/PLA) TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1402000000.html03.10.2007 22:49:54...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1403000000.html 14.3 POWER SUPPLY BLOCK DIAGRAM (DVD- S35PLA) TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1403000000.html03.10.2007 22:50:01...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1404000000.html 14.4 SERVO BLOCK DIAGRAM TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1404000000.html03.10.2007 22:50:11...
Page 117
RF SIGNAL MOTOR DRIVE SIGNAL TRACKING ERROR SIGNAL FOCUS ERROR SIGNAL IC2501 IC3001 (DV1) (MOTOR DRIVE) OPTICAL PICK UP UNIT VO4+ M2602 VIN5 PHOTO DETECTOR TRAVERS MOTOR LEVEL TRSDRV TRIN VO4- SHIFT VIN6 BIAS1 HEAD VIN7 OPIN+ TRDRV VIN1 VIN8 VO3+ VIN1 M2601...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1405000000.html 14.5 VIDEO BLOCK DIAGRAM TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1405000000.html03.10.2007 22:50:18...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1406000000.html 14.6 AUDIO BLOCK DIAGRAM TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1406000000.html03.10.2007 22:50:32...
Page 122
MAIN SIGNAL IC3001 IC4201 (DV1) (AUDIO D/A CONVERTER) JK4401 IC4311 MIXL OUTPUT AMP SRCK MIX L AUDIO LRCK LRCK SERIAL DATA LOW-PASS PORT ADOUT3 FILTER OVERSAMPLING ENHANCED DIGITAL FILTER A MUT FROM MULTI-LEVEL IC3001-49PIN WITH STBDAC DELTA-SIGMA FUNCTION STBDAC MODULATOR CONTROLLER SERIAL IC4311...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1500000000x.html 15 INTERCONNECTION SCHEMATIC DIAGRAM& SCHEMATIC DIAGRAM NOTES TOP PREVIOUS NEXT 15.1 INTERCONNECTION SCHEMATIC DIAGRAM 15.2 SCHEMATIC DIAGRAM NOTES TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1500000000x.html03.10.2007 22:50:44...
Page 124
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1501000000.html 15.1 INTERCONNECTION SCHEMATIC DIAGRAM TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1501000000.html03.10.2007 22:50:46...
Page 126
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1502000000.html 15.2 SCHEMATIC DIAGRAM NOTES TOP PREVIOUS NEXT This schematic diagram may be modified at any time with the development of new technology. Important safety notice: Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purpose of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc.
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1601000000.html 16.1 POWER SUPPLY SCHEMATIC DIAGRAM (DVD-S35GCS/GCU/GC/GCA/GD/PL/PX) TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1601000000.html03.10.2007 22:51:03...
Page 129
DVD-S35GCS/GCU/GC/GCA/GD/PL/PX POWER SUPPLY SCHEMATIC DIAGRAM...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1602000000.html 16.2 POWER SUPPLY SCHEMATIC DIAGRAM (DVD-S35EE/GN) TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1602000000.html03.10.2007 22:51:12...
Page 131
DVD-S35EE/GN POWER SUPPLY SCHEMATIC DIAGRAM...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1603000000.html 16.3 POWER SUPPLY SCHEMATIC DIAGRAM (DVD-S35PLA) TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1603000000.html03.10.2007 22:51:21...
Page 133
DVD-S35PLA POWER SUPPLY SCHEMATIC DIAGRAM...
Page 134
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1604000000.html 16.4 PRE SECTION (MAIN P.C.B. (1/3)) SCHEMATIC DIAGRAM (DVD-S35GCS/GCU/GC/ GCA/GD/EE/GN/PL/PLA) TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1604000000.html03.10.2007 22:51:34...
Page 135
PRE SECTION:Page DV1 SECTION:Page AV SECTION:Page DVD-S35GCS/GCU/GC/GCA/GD/EE/GN/PL/PLA PRE SECTION(MAIN P.C.B.(1/3)) SCHEMATIC DIAGRAM...
Page 136
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1605000000.html 16.5 DV1 SECTION (MAIN P.C.B. (2/3)) SCHEMATIC DIAGRAM (DVD-S35GCS/GCU/GC/ GCA/GD/EE/GN/PL/PLA) TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1605000000.html03.10.2007 22:51:44...
Page 137
PRE SECTION:Page DV1 SECTION:Page AV SECTION:Page DVD-S35GCS/GCU/GC/GCA/GD/EE/GN/PL/PLA DV1 SECTION(MAIN P.C.B.(2/3)) SCHEMATIC DIAGRAM...
Page 138
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1606000000.html 16.6 AUDIO/VIDEO SECTION (MAIN P.C.B. (3/3)) SCHEMATIC DIAGRAM (DVD-S35GCS/GCU/GC/ GCA/GD/EE/GN/PL/PLA) TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1606000000.html03.10.2007 22:51:54...
Page 139
PRE SECTION:Page DV1 SECTION:Page AV SECTION:Page DVD-S35GCS/GCU/GC/GCA/GD/EE/GN/PL/PLA AV SECTION(MAIN P.C.B.(3/3)) SCHEMATIC DIAGRAM...
Page 140
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1607000000.html 16.7 PRE SECTION (MAIN P.C.B. (1/3)) SCHEMATIC DIAGRAM (DVD-S35PX) TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1607000000.html03.10.2007 22:52:04...
Page 141
PRE SECTION:Page DV1 SECTION:Page AV SECTION:Page DVD-S35PX PRE SECTION (MAIN P.C.B.(1/3)) SCHEMATIC DIAGRAM...
Page 142
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1608000000.html 16.8 DV1 SECTION (MAIN P.C.B. (2/3)) SCHEMATIC DIAGRAM (DVD-S31PX) TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1608000000.html03.10.2007 22:52:13...
Page 143
PRE SECTION:Page DV1 SECTION:Page AV SECTION:Page DVD-S35PX DV1 SECTION (MAIN P.C.B.(2/3)) SCHEMATIC DIAGRAM...
Page 144
Рабочий стол file:///C|/Documents and Settings/eDOK/ /DVD-S35xx/s1609000000.html 16.9 AUDIO/VIDEO SECTION (MAIN P.C.B. (3/3)) SCHEMATIC DIAGRAM (DVD-S35PX) TOP PREVIOUS NEXT TOP PREVIOUS NEXT Рабочий стол file:///C|/Documents and Settings/eDOK/ /DVD-S35xx/s1609000000.html03.10.2007 22:52:22...
Page 145
PRE SECTION:Page DV1 SECTION:Page AV SECTION:Page DVD-S35PX AV SECTION (MAIN P.C.B.(3/3)) SCHEMATIC DIAGRAM...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1610000000.html 16.10 MOTOR SCHEMATIC DIAGRAM TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1610000000.html03.10.2007 22:52:31...
Page 147
DVD-S35GCS/GCU/GC/GCA/GD/EE/GN/PL/PLA/PX MOTOR SCHEMATIC DIAGRAM...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1611000000.html 16.11 OPERATION SCHEMATIC DIAGRAM TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1611000000.html03.10.2007 22:52:39...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1700000000x.html 17 PRINT CIRCUIT BOARD TOP PREVIOUS NEXT 17.1 POWER SUPPLY P.C.B. (DVD-S35GCS/GCU/GC/GCA/GD/PL/PX) 17.2 POWER SUPPLY P..B. (DVD-S35EE/GN) 17.3 POWER SUPPLY P.C.B. (DVD-S35PLA) 17.4 MAIN P.C.B. (1/2) (COMPONENT SIDE) (DVD-S35GCS/GCU/GC/GCA/GD/EE/GN/PL/PLA) 17.5 MAIN P.C.B. (2/2) (FOIL SIDE) (DVD-S35GCS/GCU/GC/GCA/GD/EE/GN/PL/PLA) 17.6 MAIN P.C.B.
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1701000000.html 17.1 POWER SUPPLY P.C.B. (DVD-S35GCS/GCU/ GC/GCA/GD/PL/PX) TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1701000000.html03.10.2007 22:52:52...
Page 152
POWER SUPPLY P.C.B. Transistors Integrated Circuits Q1021 IC1101 Q1031 IC1151 Q1051 Connectors Q1052 P1001 Q1062 PS1102 Q1116 Q1125 Q1127 Q1128 Q1155 Q1191 Transistors-resistors QR1115 QR1156 ADDRESS INFORMATION POWER SUPPLY P.C.B. DVD-S35GCS/GCU/GC/GCA/GD/PL/PX POWER SUPPLY P.C.B.(REP3560A-C)
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1702000000.html 17.2 POWER SUPPLY P..B. (DVD-S35EE/GN) TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1702000000.html03.10.2007 22:53:00...
Page 154
POWER SUPPLY P.C.B. Transistors Integrated Circuits Q1021 IC1101 Q1051 IC1151 Q1052 Connectors Q1062 P1001 Q1116 PS1102 Q1125 Q1127 Q1128 Q1155 Q1191 Transistors-resistors QR1115 QR1156 ADDRESS INFORMATION POWER SUPPLY P.C.B. DVD-S35EE/GN POWER SUPPLY P.C.B.(REP3560B-C)
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1703000000.html 17.3 POWER SUPPLY P.C.B. (DVD-S35PLA) TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1703000000.html03.10.2007 22:53:09...
Page 156
POWER SUPPLY P.C.B. Transistors Integrated Circuits Q1051 IC1021 Q1116 IC1101 Q1125 IC1151 Q1127 Connectors Q1128 P1001 Q1155 PP1101 Q1191 PS1102 Transistors-resistors QR1115 QR1156 ADDRESS INFORMATION POWER SUPPLY P.C.B. DVD-S35PLA POWER SUPPLY P.C.B.(REP3504C-1C)
Page 157
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1704000000.html 17.4 MAIN P.C.B. (1/2) (COMPONENT SIDE) (DVD- S35GCS/GCU/GC/GCA/GD/EE/GN/PL/PLA) TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1704000000.html03.10.2007 22:53:17...
Page 158
MAIN P.C.B. (1/2) DVD-S35GCS/GCU/GC/GCA/GD/EE/GN/PL/PLA (COMPONENT SIDE) MAIN P.C.B.(1/2)(REP3580F-C:GCS/GCU/GC/GCA/GD/EE/GN,REP3580D-C:PL/PLA)
Page 159
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1705000000.html 17.5 MAIN P.C.B. (2/2) (FOIL SIDE) (DVD-S35GCS/ GCU/GC/GCA/GD/EE/GN/PL/PLA) TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1705000000.html03.10.2007 22:53:25...
Page 160
* IC6351 is not supplied in the form of an individual part. When replacing, be sure to replace the main p.c.b. MAIN P.C.B. (2/2) and not IC6351 singly. (FOIL SIDE) DVD-S35GCS/GCU/GC/GCA/GD/EE/GN/PL/PLA MAIN P.C.B.(2/2)(REP3580F-C:GCS/GCU/GC/GCA/GD/EE/GN,REP3580D-C:PL/PLA)
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1706000000.html 17.6 MAIN P.C.B. ADDRESS INFORMATION TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1706000000.html03.10.2007 22:53:33...
Page 162
MAIN P.C.B.(DVD-S35GCS/GCU/GC/GCA/GD/EE/GN/PL/PLA) MAIN P.C.B.(DVD-S35PX) Transistors CP3007 F CP6314 F JK4401 Transistors CP3007 C CP6307 F TL6206 Q2101 C CP3008 F CP6315 F P2511 Q2101 C CP3008 C CP6308 F TL6207 Q4402 C CP3009 F CP6316 F PS6251 Q4402 C CP3009 C CP6309 F TL6208 Q4411...
Page 163
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1707000000.html 17.7 MAIN P.C.B. (1/2) (COMPONENT SIDE) (DVD- S35PX) TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1707000000.html03.10.2007 22:53:39...
Page 164
MAIN P.C.B. (1/2) DVD-S35PX (COMPONENT SIDE) MAIN P.C.B.(1/2)(REP3579E-C)
Page 165
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1708000000.html 17.8 MAIN P.C.B. (2/2) (FOIL SIDE) (DVD-S35PX) TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1708000000.html03.10.2007 22:53:48...
Page 166
* IC6351 is not supplied in the form of an individual part. When replacing, be sure to replace the main p.c.b. MAIN P.C.B. (2/2) and not IC6351 singly. DVD-S35PX (FOIL SIDE) MAIN P.C.B.(2/2)(REP3579E-C)
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1709000000.html 17.9 MOTOR P.C.B. TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1709000000.html03.10.2007 22:53:56...
Page 168
MOTOR P.C.B. DVD-S35GCS/GCU/GC/GCA/GD/EE/GN/PL/PLA/PX MOTOR P.C.B.(REP3501A-C)
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1710000000.html 17.10 OPERATION P.C.B. TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1710000000.html03.10.2007 22:54:03...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1801000000.html 18.1 Casing Parts& Mechanism Section Exploded View TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1801000000.html03.10.2007 22:54:20...
Page 173
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/ob_cas_v.gif file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/ob_cas_v.gif (1 of 2)03.10.2007 22:54:24...
Page 174
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/ob_cas_v.gif file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/ob_cas_v.gif (2 of 2)03.10.2007 22:54:24...
Рабочий стол file:///C|/Documents and Settings/eDOK/ /DVD-S35xx/s1802000000.html 18.2 Mechanism Section Exploded View TOP PREVIOUS NEXT TOP PREVIOUS NEXT Рабочий стол file:///C|/Documents and Settings/eDOK/ /DVD-S35xx/s1802000000.html03.10.2007 22:54:27...
Page 176
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/ob_mec_v.gif file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/ob_mec_v.gif (1 of 2)03.10.2007 22:54:30...
Page 177
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/ob_mec_v.gif file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/ob_mec_v.gif (2 of 2)03.10.2007 22:54:30...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1803000000.html 18.3 Packing& Accessories Section Exploded View TOP PREVIOUS NEXT TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1803000000.html03.10.2007 22:54:34...
Page 179
Рабочий стол file:///C|/Documents and Settings/eDOK/ /DVD-S35xx/ob_pac_v.gif Рабочий стол file:///C|/Documents and Settings/eDOK/ /DVD-S35xx/ob_pac_v.gif (1 of 2)03.10.2007 22:54:37...
Page 180
Рабочий стол file:///C|/Documents and Settings/eDOK/ /DVD-S35xx/ob_pac_v.gif Рабочий стол file:///C|/Documents and Settings/eDOK/ /DVD-S35xx/ob_pac_v.gif (2 of 2)03.10.2007 22:54:37...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1900000000p.html 19 REPLACEMENT PARTS LIST TOP PREVIOUS NEXT Notes: *Important safety notice: Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purposes of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc. are used. When replacing any of components, be sure to use only manufacture’s specified parts shown in the parts list.
Page 203
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1900000000p.html ZA1111,12 K4CZ01000027 TERMINAL ZA3002 RMCC0001 EARTH SPRING TOP PREVIOUS NEXT file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s1900000000p.html (23 of 23)03.10.2007 22:55:04...
file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s2000000000x.html 20 Schematic Diagram for printing with A4 size TOP PREVIOUS TOP PREVIOUS file:///C|/Documents and Settings/eDOK/Рабочий стол/DVD-S35xx/s2000000000x.html03.10.2007 22:55:09...
Page 205
15 INTERCONNECTION SCHEMATIC DIAGRAM & SCHEMATIC D 15.1. INTERCONNECTION SCHEMATIC DIAGRAM OPTICAL PICK UP UNIT FP5101 3.3VHFM LD+(DVD) F1(DVD) F2(DVD) GAINH/L PIN(DVD) VREF2.2(DVD) TA(DVD) TD(DVD) TC(DVD) TB(DVD) VCC5V MAIN P.C LD+(CD) T1(CD) VREF2.2(CD) FE2(CD) T2(CD) PIN(CD) P2511 MECHANISM UNIT TRAY-SW DGND TRAY OPEN...
Page 207
15.2. SCHEMATIC DIAGRAM NOTES This schematic diagram may be modified at any time with the development of new technology. Important safety notice: Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purpose of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc.
Page 216
CS/GCU/GC/GCA/GD/EE/GN/PL/PLA) PRE SECTION:Page DV1 SECTION:Page AV SECTION:Page DVD-S35GCS/GCU/GC/GCA/GD/EE/GN/PL/PLA PRE SECTION(MAIN P.C.B.(1/3)) SCHEMATIC DIAGRAM...
Page 220
VD-S35GCS/GCU/GC/GCA/GD/EE/GN/PL/PLA) PRE SECTION:Page DV1 SECTION:Page AV SECTION:Page DVD-S35GCS/GCU/GC/GCA/GD/EE/GN/PL/PLA AV SECTION(MAIN P.C.B.(3/3)) SCHEMATIC DIAGRAM...