24 infrared LED´s, Water resistant* IP standard IP65 * Only the camera unit is water resistant with IP standard IP65. Receiver, AC adaptors and other components are not water resistant. AFTER SALES SUPPORT 1 800 270 5071 YEAR WARRANTY MODEL: SC-1 WR...
Page 2
WARNING - To reduce a risk of fire or electric shock, do not expose the receiver and AC adaptors to rain or moisture.
Dear Customer, Congratulations on purchasing a high quality MAGINON® product. You have acquired a modern digital security camera with audio transmission, excellent technical features and accessories, which is easy to operate. Please read this information, in particular, the safety instructions.
2. Contents Preface Contents of box Contents Hazard, Safety and Warning notices Your video camera 4.1. Parts 4.2. Installation of security camera 4.2.1. Fitting stand to camera 4.2.2. Marking for drilling 4.2.3. Fixing to stone/concrete 4.2.4. Fixing to timber 4.2.5. Completing the camera installation 4.3.
Page 5
Conformity Care Disposal Fault removal (FAQ) Warranty and Service Technical Specification 11.1. Power supply 11.2. Security camera with integrated microphone 11.3. Receiver (2.4G radio AV receiver) Index...
3. Hazard, Safety and Warning notices Incorrect use of the camera and accessories can be dangerous for you and others and can damage or destroy the camera. We therefore ask you to read and strictly observe the following hazard, safety and warning notices. Intended use ...
Page 7
Hazard of electrocution in case of wet and humid conditions The receiver and any supplied components may not be exposed to dripping or spraying water. Containers filled with liquid, such as vases or glasses may also not be placed on or close to the receiver.
Page 8
Damage from heat – fire hazard Do not leave camera and receiver in places that are susceptible to considerable increases in temperature (e.g. in a vehicle). The housing and internal parts may be damaged, which in turn could cause a fire. ...
4. Your video camera 4.1. Parts 1. AC adaptors (2x) 5. Aerials (2x) 2. Security camera 6. Fixing material 3. Stand 7. AV Cinch cable 4. 4-channel receiver including base 8. Instruction Manual (not shown)
4.2. Installation of security camera Install the security camera in such a way that no sun light falls onto the lens. The stand can be connected to the underside or rear of the camera, depending on whether the camera is to be wall or ceiling mounted.
4.2.3. Fixing to stone/concrete To drill suitable holes for dowels use a ¼" drill bit when installing in masonry or concrete surfaces. After drilling, push dowels into hole until flush with surface. Then secure the stand by using the screws supplied. 4.2.4.
4.3. Connecting the receiver Note: • Caution! In order to prevent any damage, only connect the receiver to the power supply and switch on the playback device (monitor, TV) when all other parts have been connected. 4.3.1. Connecting the receiver to the playback device Using the yellow connector of the supplied AV Cinch cable connect the Video output (H) of the receiver to a suitable video input of your playback device.
4.3.2. Completing the receiver installation Screw an aerial into the aerial socket (l) at the rear of the receiver. The receiver can be operated standing upright on its stand or lying down horizontally. Remove foot (J) when using horizon- tally. Connect the cable of the power supply to the socket of the receiver (F).
5. Operation Note: • The transmission frequencies of the security camera and receiver have been facto- ry preset. The security camera transmits on the frequency of one of the available four reception channels of the receiver. After switch-on, the transmission channel of the used security camera must be selected on the receiver.
If the automatic channel changing function has been activated, the receiver changes reception channels at regular intervals so that alternating images of all connected cameras are shown on screen. Using the TIME SELECT (O) slide switch at the back of the receiver, channel changing intervals can be set.
5.5. Setting the channel on the security camera Note: • When using several security cameras ensure that each camera transmits on a separate channel. As 4 channels are provided, a maximum of 4 security cameras can be con- nected. Even if only one camera is used, changing the transmission channel may im- prove reception.
6. Conformity (FCC-Statement) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
7. Care The security camera and the receiver do not contain any serviceable components. Clean surfaces using a dry, soft cloth. In case of heavier soiling or for cleaning the lens of the security camera, use a moist soft cloth that has been well wrung out. Finally dry all parts with a soft, lint- free cloth.
Please contact our hotline before returning a defective device. Manufacturer’s address: Service address: Schenker INC., Chicago Branch supra Foto-Elektronik-Vertriebs-GmbH MAGINON® Service Center 1347 Mt. Prospect Rd. Denisstr. 28A Des Plaines, IL 60018 67663 Kaiserslautern Germany Tel.: 1 800 270 5071...
11. Technical Specification 11.1. Power supply Model: HL-12/2-8E6S Input: 100-240 V ~ 50-60 Hz, 200 mA Output: 12 V 0.5 A Protection class II 11.2. Security camera with integrated microphone Model: SC FR-W304C Input voltage: 12 V DC System: NTSC Transmission frequency 2.4 GHz Infrared LEDs with automatic activation during dusk conditions.