Toyota PT398-00100 Installation Manual
  1. Manuals
  2. Brands
  3. Toyota Manuals
  4. Remote Starter
  5. PT398-00100
  6. Installation manual
Toyota PT398-00100 Installation Manual

Toyota PT398-00100 Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
TOYOTA
TUNDRA
Preparation
Part Number: PT398-00100
PT398-00100-AA
Conflicts
Do not install into vehicles without RKE system.
Recommended Sequence of Application
Item #
Accessory
1
TVIP/RES Any TVIP or RES system
2
XM Radio

Kit Contents

Item #
Quantity
Description
1
1
Wire Harness
2
1
RES ECU Mounting Bracket
3
1
RES ECU Mounting Plate
4
1
Gateway ECU Bracket (See Page 2
for details)

Hardware Bag Contents

Item #
Quantity
Description
1
1
RES ECU
2
1
Gateway ECU
3
2-4
Small Foam Tape Strips (1 per.)
(See page 2 for details)
4
1
Large Foam Tape Strips (2 per)
5
25
Wire Ties
6
2
M6 Flange Nut
7
4
Window Warning Labels
(English/Spanish)
8
4
Key Labels (English/Spanish)
9
4
Key Tags (English/Spanish)
10
2
Engine Room Warning Labels
(English/Spanish)
11
1
Owner's Manual
Additional Items Required For Installation
Item #
Quantity
Description
1
1
Hood Switch Kit (08586-oc920)
for vehicles without factory alarm.
(1 V4 Hood Latch, 2 Nut Covers)
2
1
V4 Adapter Kit (PT398-34112)
NOTE: Refer to Page 18 to
determine if you will need this kit.
3
1
Black Electrical Tape
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this
accessory should follow approved guidelines to ensure a quality installation.
These guidelines can be found in the "Accessory Installation Practices" document.
This document covers such items as:
Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.)
Safety (eye protection, rechecking torque procedure, etc.)
Vehicle Disassembly/Reassembly (panel removal, part storage, etc.)
Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.)
Please see your Toyota dealer for a copy of this document.
Issue: E
04/07/10
2010 -
REMOTE ENGINE STARTER (RES)
NOTE: Part number of this accessory may not be the same as
the part number shown.

Recommended Tools

Personal & Vehicle
Protection
Safety Glasses
Safety Gloves
Vehicle Protection
Special Tools
Terminal Tension Blade
Installation Tools
Screwdriver
Nylon Panel Removal Tool
Side Cutters
Torque Wrench
Utility Knife
Tape
Wrench
Socket
Special Chemicals
Cleaner
Glass Cleaner

Legend

STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of
injury.
CAUTION: A process that must be carefully observed
in order to reduce the risk of damage to the
accessory/vehicle and to ensure a quality installation.
TOOLS & EQUIPMENT: Used in Figures calls out the
specific tools and equipment recommended for this
process.
REVISION MARK: This mark highlights a change in
installation with respect to previous issue.
SAFETY TORQUE: This mark indicates that torque is
related to safety.
Page 1 of 42 pages
TVIP V4
Notes
(Optional)
Blankets, Parts Boxes, etc.
Notes
Toyota SST # 00002-025BL-01
Or Sumitomo P/N 319-0000
Notes
#2 Phillips, Flat blade,
Jeweler's
e.g. Panel Pry Tool #1 Toyota
SST # 00002-06001-01
36 in•lbf (4.7 N•m),
71 in•lbf (8 N•m),
88.5 in•lbf (10 N•m)
Clear
10mm
10mm, Extension
Notes
VDC Approved Cleaner
Household Glass Cleaner

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PT398-00100 and is the answer not in the manual?

Questions and answers

Related Manuals for Toyota PT398-00100

Summary of Contents for Toyota PT398-00100

  • Page 1 Safety (eye protection, rechecking torque procedure, etc.) Vehicle Disassembly/Reassembly (panel removal, part storage, etc.) Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.) Please see your Toyota dealer for a copy of this document. Page 1 of 42 pages Issue: E...
  • Page 2 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) CAUTION: This kit will only work for Phase 3 Vehicles. If the Vehicle is Phase 4 you will need to use PT398-34110. See below for how to identify Phase 3 and Phase 4 If the Vehicle’s Key does not have “G”...
  • Page 3 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) CAUTION: There are three kits available for the 10MY Tundra. Two of the Kits have the same part number but different contents. The third Kit has a –AA part number.
  • Page 4 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) Page 4 of 44 pages Issue: E 04/07/10...
  • Page 5 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) Page 5 of 44 pages Issue: E 04/07/10...
  • Page 6 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) Page 6 of 44 pages Issue: E 04/07/10...
  • Page 7 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) 1. Vehicle Disassembly. (Driver’s Side) (a) Place the Vehicle in Park and set the Parking Brake before disconnecting the Battery. ELECTRONIC TILT ADJUST ONLY: Fully extend the Steering Wheel’s Tilt and Telescope positions.
  • Page 8 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) (c) Remove the Driver’s Side Step Cover. Nylon Panel Removal Tool (Fig. 1-3) Step Cover (1) Begin by protecting the Vehicle Interior with Blankets. Fig. 1-3 (d) Remove the Driver’s Side Cowl Cover.
  • Page 9 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) (h) Remove the 2 Screws that secure the Lower Phillips Screwdriver Steering Column Cover. (Fig. 1-7) (1) Insert the key into the Ignition and turn it to “ON.” (2) Turn the Steering Wheel left then right to gain access to the 2 screws securing the Cover.
  • Page 10 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) (n) Wrap the Airbag in a blanket and place on a box to avoid tension on the harness. (Fig. 1-11) Metal Substructure TVIP Box Fig. 1-11 2. Vehicle Disassembly. (Passenger’s Side) Nylon Panel Removal Tool (a) Remove the Passenger’s Step Cover.
  • Page 11 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) (d) Open the Glove Box. (Fig. 2-4) Nylon Panel Removal Tool (e) Remove the Passenger’s Dash Side Cover. (Fig. 2-4) (f) Close the Glove Box. Dash Side Cover Fig. 2-4 10mm Socket, Phillips Screwdriver Fig.
  • Page 12 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) 10mm Socket Fig. 2-7 (i) Dislodge the Passenger’s Knee Airbag. (Fig. 2-7) (1) Remove 3 Bolts. (j) Wrap the Airbag in a blanket and place on a box to avoid tension on the harness.
  • Page 13 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) (l) Remove the Glove Box. (Fig. 2-10) Phillips Screwdriver (1) Open the Glove Box. (2) Remove 2 Screws. Screws (x2) Fig. 2-10 FOR USE ON B-CAB VEHICLES (step m) CAUTION: Verify that the negative battery terminal is disconnected.
  • Page 14 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) Confirm the following: [1] Does the Vehicle have a Hood Switch Installed? If the Hood Switch 2P If the Hood Switch Connector is not connected, 2P Connector is connected, install the Hood Switch.
  • Page 15 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) Flat Blade Screwdriver (c) Remove 1 Nut Cover. (Fig 3-3) (1) Discard the Nut Cover. Nut Cover Fig. 3-3 (d) Remove the 2 Bolts and 1 Nut from the 10mm Socket Hood Latch.
  • Page 16 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) (h) Disconnect the Vehicle Hood Latch from the Hood Latch Cable. (Fig. 3-7) (1) Pull the Cable upwards and out of the notch in the Vehicle Hood Latch Casing.
  • Page 17 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) 10mm Socket, Phillips Screwdriver (n) Insert the Pin into the plastic cover. (Fig. 3-11) (o) Reinstall the Plastic Cover. (Fig. 3-11) (1) Replace the Nut Cover with 1 Nut Cover supplied in the kit.
  • Page 18 Utility Knife 5. Gateway ECU Preparation and Installation. 3/4 Foam Tape For kits w/Part number PT398-00100-AA ONLY (a) Apply 3/4 small piece of Foam Tape to the Gateway ECU as shown. (Fig. 5-1) (b) Attach the Gateway ECU Bracket to the Bracket Gateway ECU as shown.
  • Page 19 (h) Secure the 3P Connectors and the V4 Harness to the Vehicle Harness with 1 Wire Tie. (Fig. 5-5) Fig. 5-5 For kits w/Part Number PT398-00100 ONLY (i) Secure the 3P Connectors to the Vehicle Side Cutter Harness with 1 Wire Tie. (Fig. 5-6) Fig.
  • Page 20 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) NOTE: Some kits with this part number will Utility Knife have a Gateway ECU Bracket and 3 Small Foam Tapes. For this kit you will discard the Bracket and add 1 Small Foam Tape.
  • Page 21 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) (p) Carefully remove the Tape securing the Utility Knife Connector Block upper portion of the Passenger’s Side Cowl Area. (Fig. 5-11) (q) Dislodge any Pre-wire Connectors from the Vehicle Harness.
  • Page 22 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) FOR VEHICLES WITH ONE 22P CONNECTOR ONLY (steps t-x) MUST USE V4 Adapter Kit (PT398-34112) (t) Carefully remove the Tape securing the Vehicle’s 22P Connector. (Fig. 5-11) Fig. 5-11 (u) Remove the Connector Block from the Vehicle’s 22P Connector.
  • Page 23 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) (w) Connect the 5P Adaptor Connectors in between the V4’s 5P Connectors. Then connect the V4 Adaptor’s 22P Connector to the Vehicle’s Connector Block. (Fig. 5-14) Fig. 5-14 (x) Secure the 5P Connectors and the 22P Side Cutter Connectors to the Vehicle’s Harness using 2...
  • Page 24 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) (y) Use 1 Wire Tie to secure the Connectors Side Cutter and the Harness to the Vehicle Harness. (Fig. 5-14) (z) Re-tape any Pre-wire Connectors to the Vehicle Harness.
  • Page 25 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) 6. RES ECU Preparation and Installation. (a) Attach the RES ECU Bracket to the RES ECU as shown. (Fig. 6-1) Fig. 6-1 (b) Attach 2 pieces of Large Foam Tape to the sides of the RES ECU as shown.
  • Page 26 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) (f) Connect the V4 Harness’s 8P and 20P Connectors to the RES ECU. (Fig. 6-5) Fig 6-5 (g) Route the V4 Harness as shown securing it Side Cutter to the Vehicle Harness with 3 Wire Ties.
  • Page 27 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) 10mm Socket USE ONLY FOR VEHICLES WITH iPod Interface ECU (step k) (k) Dislodge the iPod Interface ECU. (Fig. 6-9) (1) Remove 1 Nut. Fig. 6-9 Side Cutter (l) Route the V4 Harness behind the Center Brace towards the Driver’s Side Area.
  • Page 28 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) USE ONLY FOR VEHICLES WITH Side Cutter MANUAL STEERING TILT (steps c-h) Wire Tie (c) Secure the V4 Harness to the Vehicle Vehicle 8P Connector Harness with 1 Wire Tie as shown.
  • Page 29 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) Side Cutter USE ONLY FOR VEHICLES WITH ELECTRONIC STEERING TILT. (steps i-q) Vehicle 8P Connector White Cable (i) Secure the V4 Harness to the Vehicle V4 8P Connector Routing Box Harness with 2 Wire Ties as shown.
  • Page 30 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) (p) Use 1 Wire Tie to secure the 8P Connectors Side Cutter Wire Ties (x2) to the Vehicle Harness. (Fig. 7-9) V4 Harness (q) Use 2 Wire Ties to secure the V4 Harness to the Vehicle Harness.
  • Page 31 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) 9. Registration (Vehicles without Immobilizer) (steps a-n) Refer to Addendum I for additional information. (a) Open the Hood. (Fig. 9-1) Fig. 9-1 (b) Temporarily reconnect the Vehicle’s Negative Battery Negative Battery Cable.
  • Page 32 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) (g) Start the Engine. (Fig. 9-5) (h) After 10 seconds stop the Engine. (Fig. 9-5) (1) The hazard lights flash 1 time. Fig. 9-5 If this procedure failed, the Hazard Lights won’t Diagnostic flash or will flash 2 times.
  • Page 33 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) If this procedure failed, the hazard Lights flash 3 Diagnostic Connectors times. Disconnect the V4 Harness’s White 1P Connectors in the Passenger’s Side Cowl Area. (Fig. 9-9) Start again from step c.
  • Page 34 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) 10. Registration (Vehicles with Immobilizer) (steps a-x) Refer to Addendum I for additional information. (a) Open the Hood. (Fig. 10-1) Fig. 10-1 Negative (b) Temporarily reconnect the Vehicle’s Battery Negative Battery Cable.
  • Page 35 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) (h) Start the Engine. (Fig. 10-5) (i) After 10 seconds stop the Engine. (Fig. 10-5) (1) The hazard lights flash 1 time. Fig. 10-5 If this procedure failed, the Hazard Lights won’t Diagnostic flash or will flash 2 times.
  • Page 36 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) (p) Insert the Key into the ignition. (Fig. 10-9) (q) Remove and insert the Key into the ignition 6 times. (Fig. 10-9) (r) Close the Driver's Door. (Fig. 10-9) (s) Open and close the Driver's Door 7 times ending in Close position.
  • Page 37 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) Diagnostic If this procedure failed, registration has failed. Connectors Disconnect the V4 harness’s White 1P Connector from the Passenger’s Side Cowl Area. (Fig. 10-11) Start again from step c.
  • Page 38 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) 11. Tags and Label Installation. For US Vehicles use the English Labels and Dispose of the Spanish Labels. For Mexico Vehicles use the Spanish Labels and Dispose of the English Labels.
  • Page 39 TOYOTA TUNDRA 2010 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) (g) Use Household Glass Cleaner to clean the Clear Tape inside of the Front Door Windows. (Fig. 11-4) (h) Use a piece of Clear Tape to lift the Label off its protective backing.
  • Page 40 TOYOTA TUNDRA 2010– TVIP V4 CHECKLIST – these points MUST be checked to ensure a quality installation. REMOTE ENGINE STARTER (RES Accessory Function Checks Close the hood, enter the vehicle and close all doors. Place the shift lever in the “P” (Park) position, set the parking brake and make sure the Vehicle is off.
  • Page 41 TOYOTA TUNDRA 2010– TVIP V4 CHECKLIST – these points MUST be checked to ensure a quality installation. REMOTE ENGINE STARTER (RES Vehicle Function Checks Function Function Enter the Vehicle Steering Wheel Column Adjusts Without Interference Horn Start the Vehicle Starter...
  • Page 42 TOYOTA TUNDRA 2010– TVIP V4 CHECKLIST – these points MUST be checked to ensure a quality installation. REMOTE ENGINE STARTER (RES Function Function HVAC Remove the short pin after Function check. Store Here Issue: E 04/07/10 Page 42 of 44...
  • Page 43 TOYOTA TUNDRA 2007 - TVIP V4 Addendum I REMOTE ENGINE STARTER (RES) Page 43 of 44 pages Issue: E 04/07/10...
  • Page 44 TOYOTA TUNDRA 2007 - TVIP V4 Addendum I REMOTE ENGINE STARTER (RES) Page 44 of 44 pages Issue: E 04/07/10...

This manual is also suitable for:

Pt398-00100-aa

Table of Contents