Ruby Tech VC-400RT+ Manual
  1. Manuals
  2. Brands
  3. Ruby Tech Manuals
  4. Network Router
  5. VC-400RT+
  6. Manual

Ruby Tech VC-400RT+ Manual

Managed vdsl2 cpe router
Hide thumbs
Table of Contents

Advertisement

Quick Links

Managed VDSL2 CPE Router MANUAL Ver. A5
VC-400RT
+
M
a
n
M
a
n
M
a
n
V
C
-
4
V
C
-
4
V
C
-
4
a
g
e
d
V
D
S
S
a
g
e
d
V
D
e
d
V
D
a
g
M
A
N
M
A
N
A
M
0
0
R
T
+
T
+
0
0
R
0
0
R
T
+
L
2
C
P
E
L
2
C
P
E
S
L
2
C
P
E
U
A
L
L
U
A
N
U
A
L
o
u
t
e
r
R
R
o
u
t
e
r
R
o
u
t
e
r

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VC-400RT+ and is the answer not in the manual?

Questions and answers

Related Manuals for Ruby Tech VC-400RT+

Summary of Contents for Ruby Tech VC-400RT+

  • Page 1 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT...
  • Page 2 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Copyright Copyright © 2012 by RubyTech Deutschland GmbH.All rights reserved. Trademarks RUBYTECH is a trademark of RubyTech Deutschland GmbH. Other brand and product names are registered trademarks or trademarks of their respective holders.
  • Page 3 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Foreword: VDSL2 Router solution Attention: Be sure to read this manual carefully before using this product. Especially Legal Disclaimer, Statement of Conditions and Safty Warnings. RubyTech' VC-400RT+ is a management of the VDSL2 CPE router that leverages the extraordinary bandwidth promise of VDSL2 (max.
  • Page 4 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Safety Warnings For your safety, be sure to read and follow all warning notices and instructions before using the device.  DO NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks.

  • Page 5: Table Of Contents

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Table of Contents Table of Contents COPYRIGHT................................FOREWORD: VDSL2 ROUTER SOLUTION......................SAFETY WARNINGS ............................. 1.1 C ............................F HECK CHAPTER 2. INSTALLING THE ROUTER......................2.1 H ..........................ARDWARE NSTALLATION 2.2 P ......................... INSTALLATION EQUIREMENTS 2.3 G .............................
  • Page 6 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT 4.5.1 xDSL Status........................31 4.6 S “WAN”........................32 ELECT 4.6.1 WAN Mode Selection......................32 4.6.2 Auto Detect Setting......................33 4.6.3 WAN Channel Config......................36 4.6.4 VLAN Channel confg.......................38 4.6.5 WAN Setting........................40 4.6.6 WAN Status........................48 4.6.7 DNS..........................50 4.6.8 DDNS..........................51 4.6.9 OAM Configuration......................52 4.7 S “LAN”..........................54...
  • Page 7 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT 4.12.1 Proxy Settings......................86 4.12.2 Snooping Settings.......................87 4.12.3 Advanced Settings.......................87 4.13 IP ..........................88 4.13.1 Tunnel Mode........................89 4.14 IP 6............................90 4.14.1 IPv6 Setting.........................91 4.14.2 6RD Configuration.......................91 4.14.3 DS-Lite Configuration....................92 4.15 D ........................93 IAGNOSTICS 4.15.1 Diagnostic Test Suite....................94 APPENDIX A: CABLE REQUIREMENTS..................95 APPENDIX B: PRODUCT SPECIFICATION.................97 APPENDIX C: ROUTER MODE SELECT..................109...

  • Page 8: Installing The Router

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Chapter 1. Installing the Router 2.1 Hardware Installation This chapter describes how to install the router, and establish the network connections. The VC-400RT+ may be installed on any level surface (e.g. a table or shelf).

  • Page 9: General Rule

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT 2.3 General Rules Before making any connections to the router, please note the following rules:  Ethernet Port (RJ-45) All network connections to the router Ethernet port must be made using Category 5 UTP or above for 100 Mbps, Category 3, 4 UTP for 10Mbps. No more than 100 meters of cabling may be use between the MUX or HUB and an end node.

  • Page 10: Connecting The Router

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT 2.4 Connecting the Router The router has four Ethernet port which support connection to Ethernet operation. The devices attached to these ports must support auto-negotiation /10Base-T / 100Base-TX / 1000Base-TX unless they will always operate at half duplex. Use any of the Ethernet ports to connect to devices such as Monitor system, Server, Switch, bridge or router.

  • Page 11: Vdsl2 Application

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Notes: Be sure each twisted-pair cable (RJ-45 ethernet cable) does not exceed 100 meters (333 feet). We advise using Category 5~7 UTP/STP cables for Cable bridge or Router connections to avoid any confusion or inconvenience in the future when you attached to high bandwidth devices.

  • Page 12: Chapter 3. Hardware Description

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT  2.6.2 Connect the VC-400LT and the VC-400RT+ to LAN Devices In the setup, usually an Ethernet tester serves as a representation of the LAN side as well as a representation of the WAN side. ...

  • Page 13: Front Panel

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT 3.1 Front Panel The figure shows the front panel. (Figure 3.1) Figure 3.1 Front Panel(VC-400RT+) 3.2 Front Indicators The router has Six LED indicators. The following Table shows the description. (Table 3-1) Color Status Descriptions...

  • Page 14: Rear Panel

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT 3.3 Rear Panel The following figure shows the rear panel. (Figure 3.2) Figure 3.2 Rear Panel And the table shows the description. (Table 3-2) Table 3-2 Description of the router rear connectors Connectors Type Description...

  • Page 15: Chapter 4. Configure The Vc-400Rt+ Via Web Browser

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT  You can use the type of signal transmitted through a wire to determine which wires should be kept separate. The rule of thumb is that wiring sharing similar electrical characteristics can be bundled together.

  • Page 16: Home

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Figure 4.1 Login Password 4.1.1 Home After successful login using the username admin, the home page of VC-400RT+ is loaded in web browser for VC-400RT+. Uesr can aslo click the “Home” on the left navigation bar. The home page displays the information screen as shown in Figure 4.1.1 Figure 4.1.1 Home Information...

  • Page 17: Quick Setup

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in Home page Field Description Version Information Software Version Shows the current version of VC-400RT+ Software loaded on the device. DSL Firmware Shows the current version of xDSL firmware loaded on the device. Applicable version only for DSL platforms.
  • Page 18 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Figure 4.1.2 Quick Setup  WAN Setup When the user clicks on Quick Setup, the WAN Setup tab is displayed as shown in Figure 4.1.2.1. The WAN Setupenables the user to configure the default WAN connection. The user has to supply fields and the CPE device will take all necessary actions to ensure the default WAN is configured.
  • Page 19 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Figure 4.1.2.2 WAN setup Dynamic IP The screen contains the following details: Fields in WAN setup Dynamic IP Field Description Channel VlanId Specify VLAN Id. Connection Specify the Connection Type from the dropdown. Type ...
  • Page 20 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT  Click Configure to configure the selected WAN connection setup. Figure 4.1.2.4 WAN setup Static IP The screen contains the following details: Fields in WAN setup Static IP Field Description Channel VlanId Specify VLAN Id.

  • Page 21: Select The Menu Level

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT 4.2 Select the Menu Level There is an easy Setup for end users at the setup of VC-400RT+ with SYSTEM, Statistics, xDSL, WAN, LAN, Route, FIREWALL, NAT, QoS , Multicast, Ipsec , IPv6, Diagonstics, Quick Setup, Home, Logout for more detail configurations.

  • Page 22: Host Name Config

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT 4.3.1 Host Name Config To configure the host name of VC-400RT+, you have to enter host and domain name. Click the Host Name Config link (System > Host Name Config) on the left navigation bar. A screen is displayed as shown in Figure 4.3.1.

  • Page 23: Administrator Settings

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Fields in System Time Field Description Current System Current Time in System shown in Day, Date and Time of day. Time Select the time zone form the list of worldwide time zones in pull-down Set Time Zone options.

  • Page 24: Web Settings

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Fields in AdministratorSettings Field Description Disable Administrator Select this to disable the web prompts for user login password. Password Select User Select user type.The available options are Admin and support_user. Current Password The user should specify the current login password.

  • Page 25: Software/Firmware Upgrade

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT  4.3.5 Software/Firmware Upgrade To update the system firmware, click the Software/Firmware Upgrade link (System > Software/Firmware Upgrade) on the left navigation bar. A screen displays the current version of VC-400RT+ Software running on the device as shown in Figure 4.3.5 Figure 4.3.5 Software/Firmware Upgrade ...
  • Page 26 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Fields in Configuration Settings Field Description Backup to local host This will backup the current active configuration of CPE in Host machine. Restore from local This will load the user supplied configuration to CPE from Host machine. host ...

  • Page 27: System Log

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT  Restore Previous Backed-up Configuration As mentioned before this option allows user to restore the earlier backed up configuration in router system. This operation is handy for restoring the system to last backed-up configuration mode. The Local Host Configuration restore are shown in Figure 4.3.6.2.
  • Page 28 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in System Log Field Description Select the mode of log. The possible options are:  Local Mode: The log text is displayed in web browser itself. ...

  • Page 29: Ssl Certificate

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT For the ease of readability, the log messages of different levels are using different colors. For example: all the debug messages are shown in green colored text.  Click Download to save the file in Host Computer. ...

  • Page 30: Select "Statistics

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT When Reset or Factory Reset is clicked, a confirmation message is displayed as shown in Figure 4.3.9.1 Figure 4.3.9.1 Reset Confirmation Message  Click Ok to perform the operation on CPE.  Click cancel to exit from this page.

  • Page 31: Wan

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in LAN Statistics: Field Description Interface Name of LAN Interface (e.g. eth0, usb0 etc.) Transmit Counters:  Total packets transmitted from this interface.  Total bytes transmitted form this interface. ...

  • Page 32: Select "Xdsl

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Fields in WAN Statistics (cont’d): Field Description Transmit Counters for WAN interface:  Total packets transmitted from this interface.  Total bytes transmitted form this interface.  Total Errorneous packets transmitted on this interface. ...

  • Page 33: Select "Wan

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in xDSL Status: Field Description ATU-C System Vendor Displays the Vendor ID, Version Number and the Serial Information Number of the ATU-C (DSLAM). Displays the status of the physical xDSL Line in terms of the Status modem, mode selected, Trellis-Coded Modulation and the Latency Type...

  • Page 34: Auto Detect Setting

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Figure 4.6.1 WAN Mode Setting(Seleted Auto) Figure 4.6.1.1 WAN Mode Setting(Seleted ADSL2+ / VDSL2) The screen contains the following details: Fields in WAN Mode Setting: Field Description Failover Support Select this checkbox to enable Dual WAN support. Primary WAN Selection Choose the WAN type from the drop down list.
  • Page 35 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT User has to provide pool of VC channels or VLAN channels which will be probed one by one sequentially and upon successful detection of a channel, WAN protocol probing will be done and configured in the device.
  • Page 36 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in Auto detect Config: Field Description This displays the current configured VLAN pool for autodetect in ADSL-PTM VLAN Pool ADSL-PTM WAN mode. Add/Delete ADSL-PTM Add or delete VLAN to ADSL-PTM VLAN pool. VLAN to Pool This displays the current configured VLAN pool for autodetect in VDSL-PTM VLAN Pool...

  • Page 37: Wan Channel Config

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Fields in Auto detect Config(cont’d): Field Description L2 MII-1 VLAN Auto Select this to enable VLAN auto detection from the specified pool for Detect MII-1 WAN mode. L2 MII-0 VLAN Auto Select this to enable VLAN auto detection from the specified pool for Detect MII-0 WAN mode.
  • Page 38 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in WAN Channel Config: Field Description The ATM based WAN channels are configured through the ATM tab. Auto Detect Enable To enable Auto Detect. Channel Name User specified VCC Name.

  • Page 39: Vlan Channel Confg

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in WAN Channel Config: Field Description VC Channel Name User specified VCC Name. VCI/VPI Virtual Path Identifier and Virtual Channel Identifier Encapsulation Mode for this VCC from dropdown - LLC/SNAP or Encapsulation Mode VCMux mode.
  • Page 40 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in VLAN Display: Field Description Auto Detect Enable To enable Auto Detect. VLAN Name User specified VLAN Channel name. Displays the L2 interface names over which VLAN Channel has been Base WAN Name configured.

  • Page 41: Wan Setting

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in VLAN Creation: Field Description VLAN Channel User specified VLAN Channel name. Name Mode Name List of L2 interfaces over which VLAN Channels can be configured. VLAN identifier in range of (7 - 4095).
  • Page 42 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The last column named DEFAULT GATEWAY allows to select the WAN for relevant WAN mode setting in WAN setting web page. When the user clicks any of the radio button, he will be asked to confirm the same.
  • Page 43 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in WAN Settings – Apply – Step1: Field Description Select the WAN Channel (e.g. PVC) from drop-down, being configured Attached Channel as WAN. To get your IP Address from your service provider (means VC-400RT+ Dynamic IP Address is DHCP client on WAN) click Apply.
  • Page 44 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT 4.6.5.2 Static IP Address To configure the WAN interface to use a static IP address, select the option Static IP Address in the WAN Settings screen. A screen is displayed as shown in Figure 4.6.5.4 Figure 4.6.5.4 WAN Static IP The screen contains the following details: Fields in Static IP:...
  • Page 45 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT  Click Apply at any time during configuration to save the information that you have entered.  Click Cancel to exit from this page without saving the changes. 4.6.5.3 PPPoE To configure the WAN interface to use PPPoE, choose the option PPPoE. A screen is displayed as shown in Figure 4.6.5.5 Figure 4.6.5.5 WAN PPPoE creation The screen contains the following details:...
  • Page 46 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Fields in PPPoE WAN (WAN IPv6 Configuration): Field Description This option allows to select following modes of IPv6 configuration:  Configuration Modes Stateful DHCPv6(IA_NA and IA_PD)  SLAAC (Address Configuration) with DHCPv6 (IA_PD) This option allows to configure different DUID (DHCP Unique Identifier) types: ...
  • Page 47 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Figure 4.6.5.6 WAN PPPoA creation The screen contains the following details: Fields in PPPoA WAN: Field Description User Name To enter the username to be used in the PPPoA session. Password To enter the corresponding password for the specified username. Please retype your password To enter the password again to reconfirm.
  • Page 48 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Fields in PPPoA WAN IPv6 Configuration: Field Description This option allows to select following modes of IPv6 configuration:  Configuration Modes Stateful DHCPv6(IA_NA and IA_PD)  SLAAC (Address Configuration) with DHCPv6 (IA_PD) This option allows to configure different DUID (DHCP Unique Identifier) types: ...

  • Page 49: Wan Status

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Figure 4.6.5.7 Bridge WAN Setting The screen contains the following details: Fields in Bridge Configuration: Field Description This option allows to configure default route for relevant WAN Default WAN mode of this WAN connection. ...
  • Page 50 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Figure 4.6.6 WAN Status The screen contains the following details: Fields in WAN Status: Field Description IPv4/IPv6 Choose the appropriate tab to view the status. For the currently configured WAN interface, this gives the layer-2 WAN Channel WAN channel information (such as ATM VCC).

  • Page 51: Dns

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT When you click on the IPv6 tab in the WAN Status page, a screen is displayed as shown in Figure 4.6.6.1 Figure 4.6.6.1 WAN Status IPv6 Tab The screen contains the details as described in table of “Fields in WAN Status”. 4.6.7 DNS To configure the Domain Name Server (DNS) address, click the DNS link (WAN >...

  • Page 52: Ddns

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in DNS: Field Description Select the appropriate tab to configure IPv4 or IPv6. IPv6 IPv4/IPv6 support is currently not available for DNS configuration. Domain Name Server (DNS) Enter the DNS address of the primary DNS server.

  • Page 53: Oam Configuration

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in DDNS: Field Description Enable DDNS support Check box to enable DDNS support in CPE. WAN Interface name from dropdown for DDNS resolution. The DDNS agent WAN Interface running in CPE keeps track of changes in IP address of chosen WAN and informs DNS service provider.
  • Page 54 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in ADSL OAM F5 Test page: Field Description This table displays all active connections with following OAM parameters information:  No: Number  VPI: Virtual Path Identifier OAM F5 Setting ...

  • Page 55: Select "Lan

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Figure 4.6.9.2 Test Failed The screen contains the following details: Fields in ADSL OAM F5 Test Page: Field Description VPI/VCI Displays the selected VPI/VCI channel of the OAM F5 Setting Table. Cells Tx Count of total number of transmitted ATM cells.

  • Page 56: Lan Arp List

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT 4.7.1 LAN ARP List To view the ARP entries list that is currently present in CPE, click the LAN ARP List link (LAN > LAN ARP List) on the left navigation bar. A screen is displayed as shown in Figure 4.7.1 Figure 4.7.1 ARP List The screen contains the following details:...
  • Page 57 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in LAN Settings: Field Description IP Address Used to enter the LAN interface IP Address of CPE device. Subnet Mask To enter the LAN Subnet Mask of CPE device. MAC Address of LAN bridge device.
  • Page 58 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Field Description DHCP Server IP Pool Starting DHCPv4 pool start IPv4 address. Address IP Pool Ending DHCPv4 pool end IPv4 address. Address Lease Lease Time for every DHCP leased entry. Select from dropdown of allowed values. Time Local Domain...
  • Page 59 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in LAN Settings: Field Description Host Name Host Computer name. IP Address to be statistically reserved for this host identified by MAC IP Address address. MAC Address MAC address of Host computer for which static IP reservation is needed.
  • Page 60 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Figure 4.7.2.3 LAN Settings - IPv6 Tab (Option 2: SLAAC) Figure 4.7.2.4 LAN Settings - IPv6 Tab (Option 3: Statefull DHCPv6 Server) For LAN interface, the VC-400RT+ uses SLAAC based prefix assignment to LAN hosts. The IPv6 prefix obtained from DHCPv6 on WAN is automatically passed to LAN hosts for their IPv6 address configuration.

  • Page 61: Upnp Devices List

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Figure 4.7.2.5 Prefix Delegated view  Click Back to exit from this page. 4.7.3 UPnP Devices List To discover the UPnP Devices in LAN network, click the UPnP Devices link (LAN > UPnP Devices) on the left navigation bar.

  • Page 62: Lan Port Status

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Figure 4.7.4 All LAN Port Setting  Default value is “Auto 10/100 Full/Half”.  Click APPLY to save the information that has been entered.  Click CANCEL to exit from this page without saving the changes. 4.7.5 LAN Port Status To discover the LAN Port Status in LAN network, click the LAN Port Status link (LAN >...

  • Page 63: Static Routing

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Figure 4.8 Route Options on the Left Navigator Bar 4.8.1 Static Routing The static routing function determines the path that data follows over your network before and after it passes through your router. You can use static routing to allow different IP domain users to access the Internet through this VDSL2 Router device.

  • Page 64: Rip Support

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Notes: 1. Static Routing functionality is used to define the connected Gateway between the LAN and WAN. For example, if we want to activate the Network Time Protocol (NTP) service, and we have to define the Gateway connected to NTP server in the WAN.

  • Page 65: Routing Table List

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in Dynamic Routing: Field Description Dynamic Routing To enable or disable the Dynamic Routing (RIP) in CPE. To configure the listen mode of RIP to: ...

  • Page 66: Select "Firewall

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in Static Routing: Field Description Destination IP Destination IPv4 address for route. Subnet Mask Destination IPv4 subnet mask for route. Gateway IPv4 gateway address for this route. Routing metric is number used by the routing protocol.

  • Page 67: Firewall Setting

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Figure 4.9 Firewall Options 4.9.1 Firewall Setting To enable or disable the firewall, click the Firewall Setting link (Firewall > Firewall Setting) on the left navigation bar. A screen is displayed as shown in Figure 4.9.1 Figure 4.9.1 Firewall Setting The screen contains the following details: Fields in Firewall Setting:...

  • Page 68: Packet Filtering

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Figure 4.9.2 IPv6 Firewall Setting The screen contains the following details: Fields in UPnP Settings: Field Description The available options are Off, CPE policy, Firewall Mode High and Low.  Click APPLY for committing the desired action. ...
  • Page 69 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in Packet Filtering: Field Description IPV4/IPv6 Choose the appropriate tab to configure. To enable or disable the Packet Filter feature of VC-400RT+ CPE. Enable Packet Filter To enable, select the check box.
  • Page 70 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in“Add a Packet Filtering Rule” page: Field Description To select the protocol. The options available are ALL, TCP, Protocol UDP, ICMP, AH and ESP. The source IP can be a SINGLE address or a SUBNET, Source IP involving a range of IP addresses.

  • Page 71: Url Filtering

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in “Add a Packet Filtering Rule - IPv6” page: Field Description To specify the input interface of the packet from dropdown options. (e.g. Ingress Interface WAN1).

  • Page 72: Parental Control

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in URL Blocking: Field Description URL of the domain that needs to be blocked. For example: Domain Name www.google.com.tw Select Select this option to remove the URL entry from blocked list. ...

  • Page 73: Application Server Settings

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT  Click Apply at any time during configuration to save the information that you have entered.  Click Cancel to exit from this page without saving the changes. 4.9.6 Application Server Settings To configure the Application Server Settings, click the Application Server Settings link (Firewall >...

  • Page 74: Access Control List (Acl)

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT  Click Apply for committing the App Server settings.  Click Cancel to exit from this page without saving the changes. 4.9.7 Access Control List (ACL) To configure the access control list, click the ACL link (Firewall > ACL) on the left navigation bar. This can be used for allowing specified IP addresses to access the VC-400RT+ CPE from WAN.

  • Page 75: Nat Settings

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Figure 4.10 NAT Options 4.10.1 NAT Settings To configure Network Address Translation (NAT), click the NAT Settings link (NAT > NAT Settings) on the left navigation bar. A screen is displayed as shown in Figure 4.10.1 Figure 4.10.1 Network Address Translation (NAT) Settings The screen contains the following details: Fields in Network Address Translation:...
  • Page 76 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Figure 4.10.2 Virtual Server The screen contains the following details: Fields in Virtual Server Page: Field Description Application Configured Application Name for Virtual Server rule. Name Private IP Private IP address of Virtual Server rule. Remote IP Remote IP address of Virtual Server rule.
  • Page 77 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Figure 4.10.2.1 Virtual Server Add The screen contains the following details: Fields in Virtual Server - Add: Field Description Specify Application name from dropdown or custom name for Virtual Application Name Server rule. Protocol Specify Virtual Server protocol - TCP or UDP or Both i.e.

  • Page 78: Port Triggering

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT 4.10.3 Port Triggering To configure Port Triggering, click the Port Triggering link (NAT > Port Triggering) on the left navigation bar. A screen is displayed as shown in Figure 4.10.3 Figure 4.10.3 Port Triggering The screen contains the following details: Fields in Port Triggering: Field...
  • Page 79 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT When you click Add button in the Port Triggering page, a screen is displayed as shown in Figure 4.10.3.1. Figure 4.10.3.1 Port Triggering Add The screen contains the following details: Fields in Port Triggering: Field Description Application...

  • Page 80: Dmz

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT 4.10.4 DMZ To configure the DMZ (Demilitarized Zone), click the DMZ link (NAT > DMZ) on the left navigation bar. Upon configuration of DMZ all traffic sent towards RG would be unconditionally forwarded to DMZ Lan Host.

  • Page 81: Qos Settings

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT 4.11.1 QoS Settings To configure the Quality of Service (QoS) Settings, click the QoS Settings link (QoS > QoS Settings) on the left navigation bar. A screen is displayed as shown in Figure 4.11.1 Figure 4.11.1 QoS Settings The screen contains the following details: Fields in QoS Settings:...

  • Page 82: Queue Config

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT 4.11.2 Queue Config To configure the Queu e Config, click the Queue Config link (QoS > Queue Config) on the left navigation bar. A screen is displayed as shown in Figure 4.11.2 Figure 4.11.2 Queue Config he screen contains the following details: Fields in Queue Config - Upstream...
  • Page 83 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT hen you click Add b utton in the Port Triggering page, a screen is displayed as shown in Figure 4.11.2.1. Figure 4.11.2.1 Add/Modify a Queue Entry he screen contains the following details: Fields in Add/Modify a Queue Entry: Field Description...

  • Page 84: Class Config

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT 4.11.3 Class Config To classify the upstrea m traffic. Click the Class Config link (QoS > Class Config) on the left avigation bar. A screen is displayed as shown in Figure 4.11.3 Figure 4.11.3 Class Config The screen contains the fo llowing details:...
  • Page 85 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Figure 4.11.3.1 Add/Modify a Classifier Rule (DSCP Based) Figure 4.11.3.1 Add/Modify a Classifier Rule(MFC Based)
  • Page 86 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in Add/Modify a Classifier Rule: Field Description This is the name of Classifier. This is an Unique identifier for an Classifier Name instance of classifier rule. Enable This is used to enable or disable the QoS Classifier entry.

  • Page 87: Multicast

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT  Click Apply for applying the changes.  Click CANCEL to exit from this page without saving the changes. 4.12 Multicast You can view Multicast on the left navigation bar of the VC-400RT+ CPE homepage. The menu below includes the sub-menus of Proxy Settings, Snooping Settings and Advanced Settings.

  • Page 88: Snooping Settings

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT  Click Apply at any time during configuration to save the information that you have entered.  Click CANCEL to exit from this page without saving the changes. 4.12.2 Snooping Settings To configure the Multicast Snooping settings, click the Snooping Settings link (Multicast > Snooping Settings) on the left navigation bar.

  • Page 89: Ipsec

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in Multicast Advanced Settings: Field Description IPv4/IPv6 Choose the appropriate tab to configure either for IPv4 or IPv6. To enable or disable Fast-Leave support in IGMPv3/IGMPv2. The fast-leave is not to wait till group membership timers on multicast routers have Fast Leave...

  • Page 90: Tunnel Mode

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT 4.13.1 Tunnel Mode When you click the Tunnel Mode link (IPsec > Tunnel Mode) on the left navigation bar, a screen is displayed as shown in Figure 4.13.1 Figure 4.13.1 IPsec Tunnel Configuration When you click Add button in the IPsec Tunnel Configuration page, a screen is displayed as shown in Figure 4.13.1.1 Figure 4.13.1.1 Add IPSec Tunnel Mode Configuration...
  • Page 91 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in Add IPSec Add Configuration: Field Description Tunnel IPsec Tunnel name Name AUTH_ME This is the authentication method. THOD Shared secret string used for tunnel authentication. Secret IKE Mode IKE v1 or v2 algorithm...

  • Page 92: Ipv6 Setting

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT 4.14.1 IPv6 Setting To enable or disable IPv6 functionality in CPE, click the IPv6 Setting link on the left navigation bar. A screen is displayed as shown in Figure 4.14.1. By default IPv6 is not enabled. Figure 4.14.1 IPv6 Setting The system wide IPv6 feature can be enabled or disabled through this web page.

  • Page 93: Ds-Lite Configuration

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in 6RD Configuration: Field Description General Settings Enable 6rd To enable or disable 6rd functionality in CPE. tunnel Select WAN interface form dropdown on which 6rd tunnel WAN Interface to be created.

  • Page 94: Diagnostics

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT The screen contains the following details: Fields in DS-Lite Configuration: Field Description General Settings Enable DS-Lite tunnel To enable/disable DS-Lite functionality in CPE. Select WAN interface from dropdown on which WAN Interface DS-Lite tunnel has to be created.

  • Page 95: Diagnostic Test Suite

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT 4.15.1 Diagnostic Test Suite To configure the Diagnostic Test Suite settings, click the Diagnostic Test Suite link (Diagnostics > Diagnostic Test Suite) on the left navigation bar. A screen is displayed as shown in Figure 4.15.1 Figure 4.15.1 Diagnostic Test Suite The screen contains the following details:...

  • Page 96: Appendix A: Cable Requirements

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Appendix A: Cable Requirements A.1 Ethernet Cable A CAT 3~7 UTP (unshielded twisted pair) cable is typically used to connect the Ethernet device to the router. A 10Base-T cable often consists of four pairs of wires, two of which are used for transmission.
  • Page 97 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT A.2 Telephone wire Standard telephone wire of any gauge or type-flat, twisted or quad is used to connect the Modem to the telephone network. A telephone cable typically consists of three pairs of wires, one of which is used for transmission.

  • Page 98: Appendix B: Product Specification

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Appendix B: Product Specification Key Features & Benefits  Support ATM and PTM transmission mode auto detection ( ADSL Annex B backward compatible)  Supports high bandwidth up to 100Mbps symmetric over line ports ...
  • Page 99 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Product Specification IEEE802.3/802.3u/802.3z standards Standard: ITU-T G992.1/G992.3/G992.5/G993.1/G997.1/G993.2 standards 4 x RJ-45 10/100/1000Mbps Ethernet port 1 x RJ-11/Terminal Block connector for VDSL2 line port Physical Interface: 1 x RJ-11 connector for POTS/ISDN device 1 x console port(RS232C/115200bps) Full duplex: IEEE 802.3x Flow control:...

  • Page 100: Appendix C: Router Mode Select

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Appendix C: Router Mode select This appendix describes how to select the router mode, The VC-400RT+ default mode is switch(bridged mode), please refer to the following steps to select the router mode or switch mode. ...

  • Page 101: Appendix D: Vc-400Lt/Vc-400Rt+ Performance Table

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Figure C-3 Config WAN Type  Click Apply for applying the changes.  Click CANCEL to exit from this page without saving the changes. Appendix D: VC-400LT/VC-400RT+ Performance Table  Test Environment: Test Items Descriptions VDSL2 CO Router x 1...
  • Page 102 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT  Compatibility Table(VC-400LT / VC-400RT+): The following shows the band profile and band plan compatibility table: Band Profile List Band Plan List VDSL2 Profile8a Annex A M1_EU32 VDSL2 Profile8b Annex A M9_EU64 VDSL2 Profile8c Annex B 997-M2x-A (B05) VDSL2 Profile8d...
  • Page 103 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Profile: 8A - Annex B-997-M2x-M Profile: 8B- Annex B-997-M2x-A Cable Length Cable Length US [Mbps] US [Mbps] (meters) [Mbps] (meters) [Mbps] 58.01 23.54 58.59 27.93 33.69 3.81 37.01 8.11 1000 1000 1600 20.80 0.67 1700...
  • Page 104 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Profile: 12A- Annex B 998-M2x-B Profile: 12B- Annex A M1_EU32 Cable Length Cable Length US [Mbps] US [Mbps] (meters) [Mbps] (meters) [Mbps] 85.55 33.01 85.74 32.42 75.20 26.37 78.13 24.02 33.50 2.83 31.64 3.42 1200...
  • Page 105 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Profile: 12B- Annex B 998-M2x-NUS0 Profile: 17A- Annex A M1_EU32 Cable Length Cable Length US [Mbps] US [Mbps] (meters) [Mbps] (meters) [Mbps] 85.84 33.59 33.79 81.54 31.25 1000 48.54 5.08 74.71 24.41 25.59 0.78 1500...
  • Page 106 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Profile: 17B- Annex B 998-M2x-B Profile: 30A- Annex A M1_EU32 Cable Length Cable Length US [Mbps] US [Mbps] (meters) [Mbps] (meters) [Mbps] 33.89 83.89 48.63 5.27 29.98 1000 1200 36.13 1.56 1000 46.88 2.83 29.30...
  • Page 107 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Appendix E: Troubleshooting Diagnosing the Router’s Indicators The router can be easily monitored through its comprehensive panel indicators. These indicators assist the network manager in identifying problems the hub may encounter. This section describes common problems you may encounter and possible solutions.
  • Page 108 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT 3. Symptom: VDSL Link cannot be established. Cause: VDSL setting failure or phone cable length is over the specification limit. Please make sure that the phone wire must be connected between VC-400LT(CO) and VC-400RT+ (CPE) when both are power on.
  • Page 109 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT 5. Question: What is SNR(Signal-to-Noise)? (Only reference) Signal-to-noise ratio (often abbreviated SNR or S/N) is a measure used in science and engineering that compares the level of a desired signal to the level of background noise. It is defined as the ratio of signal power to the noise power.
  • Page 110 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT We need to set up a default gateway on a NV-600 pair which are in Bridge mode, as they 8. Question: want to manage the units from a different network. When the application is used within the LAN, the switch(bridged) mode is not necessary to set up a gateway .However, if the application crosses various network segments (LAN to WAN or WAN to LAN), you must set up a gateway to connect different network segment.

  • Page 111: Appendix E: Troubleshooting

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT System Diagnostics Power and Cooling Problems If the POWER indicator does not turn on when the power cord is plugged in, you may have a problem with the power outlet, power cord, or internal power supply as explained in the previous section.

  • Page 112: Appendix F: Compliance Information

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Appendix F: Compliance Information FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a computing device, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
  • Page 113 Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT FCC Warning This equipment has been tested to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

  • Page 114: Warranty

    Managed VDSL2 CPE Router MANUAL Ver. A5 VC-400RT Warranty The original product that the owner delivered in this package will be free from defects in material and workmanship for one year parts after purchase. There will be a minimal charge to replace consumable components, such as fuses, power transformers, and mechanical cooling devices.

Table of Contents