Toyota 2011 Matrix Owner's Manual

page of 516

/ 516
Contents
Table of Contents
Bookmarks

Table of Contents

Quick Links

Abbreviation list

Abbreviation/Acronym list

ABBREVIATIONS

4WD

A/C

ABS

ACC

ALR

AWD

CRS

ECU

EDR

ELR

GAWR

GVWR

I/M

LATCH

LED

MMT

M + S

MTBE

OBD

SRS

TIN

TPMS

TRAC

VIN

VSC

488

MEANING

4 Wheel Drive

Air Conditioning

Anti-lock Brake System

Accessory

Automatic Locking Retractor

All Wheel Drive

Child Restraint System

Electronic Control Unit

Event Data Recorder

Emergency Locking Retractor

Gross Axle Weight Rating

Gross Vehicle Weight Rating

Emission inspection and maintenance

Lower Anchors and Tethers for Children

Light Emitting Diode

Methylcyclopentadienyl Manganese Tricarbonyl

Mud and Snow

Methyl Tertiary Butyl Ether

On Board Diagnostics

Supplemental Restraint System

Tire Identification Number

Tire Pressure Warning System

Traction Control

Vehicle Identification Number

Vehicle Stability Control

Table of Contents

Need help?

Do you have a question about the 2011 Matrix and is the answer not in the manual?

Questions and answers

Summary of Contents for Toyota 2011 Matrix

Page 1 Abbreviation list Abbreviation/Acronym list ABBREVIATIONS MEANING 4 Wheel Drive Air Conditioning Anti-lock Brake System Accessory Automatic Locking Retractor All Wheel Drive Child Restraint System Electronic Control Unit Event Data Recorder Emergency Locking Retractor GAWR Gross Axle Weight Rating GVWR Gross Vehicle Weight Rating Emission inspection and maintenance LATCH Lower Anchors and Tethers for Children...
Page 2: For Your Information
A wide variety of non-genuine spare parts and accessories for Toyota vehicles are currently available on the market. You should know that these parts are not covered by Toyota warranty and that Toyota is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.
Page 3 Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by a qualified service shop or by your Toyota dealer before you scrap your vehicle.
Page 4 CAUTION ■ General precautions while driving Driving under the influence: Never drive your vehicle when under the influ- ence of alcohol or drugs that have impaired your ability to operate your vehi- cle. Alcohol and certain drugs delay reaction time, impair judgment and reduce coordination, which could lead to an accident that could result in death or serious injury.
Page 5 This is a warning against anything which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your Toyota and its equipment.
Page 7: Table Of Contents
TABLE OF CONTENTS Adjusting and operating features such as door locks, Before driving mirrors, and steering column. When driving Driving, stopping and safe-driving information. Interior fea- Air conditioning and audio systems, as well as other in- tures terior features for a comfortable driving experience. Maintenance Cleaning and protecting your vehicle, performing do-it- and care...
Page 8 Pictorial index Exterior Headlights (low beam) P. 135 Headlights (high beam) and daytime ∗ Moon roof P. 59 running lights P. 135, 136 Outside rear view Hood P. 332 mirrors P. 55 Front turn signal/parking and front side marker lights P.
Page 9 Rear window defogger P. 179 Fuel filler door P. 62 ∗ Rear window wiper P. 140 Doors P. 29 Back door P. 34 License plate lights P. 135 Tires ●Rotation P. 351 ●Replacement P. 411 Stop/tail and rear side ●Inflation pressure P.
Page 10 Pictorial index Interior Seat belts SRS driver airbag P. 46 P. 71 Head restraints P. 44 Bottle holders P. 290 Power window SRS front passenger ∗ switches airbag P. 57 P. 71 Glove box Bottle holders P. 290 P. 287 Cup holders P.
Page 11 Vehicles with moon roof Vanity mirrors P. 294 Sun visors P. 293 Auxiliary box P. 291 Moon roof switches P. 59 SRS curtain shield airbags P. 71 Interior lights P. 283 Personal/interior lights P. 284 Anti-glare inside rear view mirror P.
Page 12 Pictorial index Interior Vehicles without moon roof Vanity mirrors P. 294 Sun visors P. 293 Personal lights P. 285 SRS curtain shield airbags P. 71 Interior lights P. 283 Anti-glare inside rear view mirror P. 53...
Page 13 ∗ Door lock switch P. 29 Inside door lock button P. 30 ∗ Window lock switch P. 57 ∗ Power window switches P. 57 ∗ : If equipped...
Page 14 Pictorial index Interior ∗ Power outlet P. 298 Cup holders P. 288 ∗ Power outlet P. 298 Parking brake lever P. 127 ∗ Cigarette lighter P. 297 ∗ AUX port P. 225 ∗ AUX port/USB port P. 206, 213, 225 ∗...
Page 15 Pictorial index Instrument panel Gauges and meters P. 129 Headlight switch P. 135 Turn signal lever P. 126 Emergency ∗ Fog light switch P. 137 flasher switch P. 390 Security indicator Horn Audio system P. 180 Outside rear view P. 66 P.
Page 16 Pictorial index Instrument panel Air conditioning system P. 172 Rear window and outside rear view mirror defogger ∗ ∗ switch /rear window defogger switch P. 179...
Page 17 Engine (ignition) switch P. 115 Audio remote control ∗ Telephone switches switches P. 227 P. 253 ∗ Cruise control switch P. 141 ∗ Talk switch P. 253 ∗ : If equipped...
Page 18 Pictorial index Instrument panel Clock P. 295 Shift lock override Shift lever P. 119, 124 ∗ button P. 426...
Page 19 VSC/TRAC off switch P. 145 Auxiliary box P. 291 Hood lock release lever P. 332 ∗ : If equipped...
Page 20: Before Driving
TABLE OF CONTENTS Index 1-7. Safety information Before driving Correct driving posture ..69 SRS airbags ......71 Front passenger occupant 1-1. Key information classification system... 83 Keys ........24 Child restraint systems ..88 Installing child restraints ..92 1-2.
Page 21: Interior Features
2-4. Using other driving Operating a USB memory ......213 systems Optimal use of the audio Cruise control...... 141 system......221 Driving assist systems ..145 Using the AUX port..... 225 Using the steering wheel 2-5. Driving information audio switches....227 Cargo and luggage .....
Page 22: Maintenance And Care
TABLE OF CONTENTS Index 3-5. Using the interior lights Maintenance and care Interior lights list ....282 • Interior light ...... 283 • Personal/interior lights..284 4-1. Maintenance and care • Personal lights ....285 Cleaning and protecting the vehicle exterior ... 316 3-6.
Page 23: When Trouble Arises
When trouble arises Vehicle specifications 5-1. Essential information 6-1. Specifications Emergency flashers .... 390 Maintenance data (fuel, oil level, etc.) ... 442 If your vehicle needs to be towed ......391 Fuel information....457 If you think something is Tire information ....460 wrong ........
Page 24 MATRIX 2 0 1 1 QUICK REFERENCE GUIDE...
Page 25 Owner’s Manual and supplementary manuals so you will have a better understanding of your vehicle’s capabilities and limitations. Your dealership and the entire staff of Toyota Motor Sales, U.S.A., Inc. wish you many years of satisfied driving in your new Corolla Matrix.
Page 26 Seat belts EMERGENCY FEATURES Seat belts-Shoulder belt anchor Spare tire & tools Tire Pressure Monitoring (warning) System 20 Visit your Toyota dealer for information on customizing this feature. Programmable by customer. Refer to the Owner’s Manual for instructions and more information.
Page 27 OVERVIEW Instrument panel Steering wheel controls Steering wheel audio controls Telephone controls* Voice command button* Ignition switch Cruise control* VSC/TRAC OFF switch Auxiliary storage Power outside rearview mirror control Headlight, turn signal and front fog light* controls Wiper and washer controls “AIR BAG ON”...
Page 28 Front passenger seat belt reminder light Engine immobilizer indicator Emergency flasher button Audio system Air Conditioning controls Outside rearview mirrors*/Rear window defogger button Tire Pressure Monitoring (warning) System reset Tilt and telescopic steering control Hood lock release lever * If equipped...
Page 29 (alarm will sound if speed is over 12 mph) Charging system warning AIR BAG ON and AIR BAG OFF indicator If indicator does not turn off within a few seconds of starting engine, there may be a malfunction. Have vehicle inspected by your Toyota dealer.
Page 30 Electric power steering warning Malfunction/Check Engine indicator Low fuel level warning Open door warning SRS Airbag warning Low Tire Pressure Warning Headlight low/high beam indicator Turn signal indicator Fog light indicator Slip indicator Engine immobilizer system indicator Vehicle Stability Control off indicator Traction control OFF indicator Cruise control indicator Cruise control SET indicator...
Page 31 OVERVIEW Keyless entry (if equipped) Locking operation Unlocking operation Push ONCE: Driver door TWICE: All doors NOTE: If a door is not opened within 60 seconds of unlocking, all doors will Push relock for safety. Panic button Push and hold Fuel tank door release and cap Pull Turn to open...
Page 32 Hood release Pull up latch Pull and raise hood Engine maintenance 4 cylinder (2AZ-FE) engine 4 cylinder (2ZR-FE) engine Engine coolant reservoir Engine oil filler cap Engine oil level dipstick Windshield washer fluid tank NOTE: Regularly scheduled maintenance, including oil changes, will help extend the life of your vehicle and maintain performance.
Page 33 FEATURES/OPERATIONS Auto lock/unlock (if equipped) Automatic door locks can be programmed to operate in three different modes, or turned OFF. -Doors lock when shifting from Park. -Doors unlock when shifting into Park. -Doors unlock when the driver’s door is opened within 10 seconds after setting the ignition switch to “ACC”...
Page 34 Seat adjustments-Front Seat position (forward/backward) Height crank (driver side only) Seatback angle Seats-Head restraints Rear Front Lock release button Lock release button Seat adjustments-Rear Pull Fold down...
Page 35 FEATURES/OPERATIONS Parking brake Release (2) Push (1) Pull slightly Pull (3) Lower Tilt and telescopic steering wheel Lock release lever Angle Length Hold wheel, push lever down, set angle and length, and return lever. NOTE: Do not attempt to adjust while the vehicle is in motion. Clock Hour set Minute set...
Page 36 Lights & turn signals Headlights Headlights Parking lights High beam Low beam High beam flasher Daytime Running Light system (DRL) Headlights turn on automatically upon starting engine. The brightness of the headlights will automatically change depending on the darkness of the surroundings. Front fog lights (if equipped) Turn Front fog lights come on only when the headlights are on low beam.
Page 37 FEATURES/OPERATIONS Windshield wipers & washers Front Intermittent windshield wiper frequency adjustment (if equipped) Single wipe Increase Interval wipe Slow Fast Decrease Pull to wash and wipe Rear (if equipped) Wash and wipe Wipe Interval wipe Wash and wipe NOTE: Rear wiper and washer operate only when back window is fully closed.
Page 38 Moonroof (if equipped) Sliding operation Tilting operation Recommended open position to minimize wind noise. Open Tilt Close Close Push once to open partway; again to open completely. Door-Back Lock Unlock Open Door locks-Power (if equipped) Unlock Lock...
Page 39 FEATURES/OPERATIONS Audio Type 1 functions Preset buttons - functions in other modes indicated above number Eject CD Push to Push and turn turn to ON/OFF adjust tone & balance Seek Push to skip station/ up/down CD track folder and select radio category Mode...
Page 40 Radio To preset stations Tune in the desired station and hold down a preset button (from or one of ) until you hear a beep. Push desired preset button (from or one of ) to select. To scan stations Push and hold “SCAN” to scan preset stations. Push again to hold selection.
Page 41 FEATURES/OPERATIONS Air Conditioning/Heating Airflow vent Use “ ” or “ ” mode to reduce window fogging (system automatically switches to fresh air mode). Fan speed Temperature selector For quick cooling, turn to MAX A/C position and select recirculated air mode (“ ”...
Page 42 Cruise control (if equipped) Turning system ON/OFF System ON/OFF Functions Resume Increase speed Cancel Set/Decrease speed The set speed may also be cancelled by depressing the brake pedal. The set speed may be resumed once vehicle speed exceeds 25 mph. Auxiliary storage Instrument panel Pull...
Page 43 Refer to “Using the hands-free phone system (for cellular phones),” Section 3-4 in the Owner’s Manual, or go to Toyota.LetsTalk.com for more information about phone connections and compatibility. Cup holders...
Page 44 Bottle holders Rear Front Power outlet-12V DC Designed for 12V car accessories. The ignition switch must be in the “ACC” or “ON” position. Power outlet-115V AC (if equipped) The ignition switch must be in the “ON” position.
Page 45: Safety And Emergency Features
If the tire pressure indicator flashes for more than 60 seconds and then remains on, take the vehicle to your local Toyota dealer. NOTE: The warning light may come on due to temperature changes or changes in tire pressure from natural air leakage. If the system has not been initialized recently, setting the tire pressures to factory specifications should turn off the light.
Page 46 Seat belts Take up slack Too high Keep as low on hips as possible If belt is fully extended, then retracted even slightly, it cannot be re-extended beyond that point, unless fully retracted again. This feature is used to help hold child restraint systems securely. To find more information about seat belts, and how to install a child restraint system, refer to the Owner's Manual.
Page 47 CUSTOMER EXPERIENCE CENTER 1-800-331-4331 Printed in U.S.A. 11/10 Cert no. SGSNA-COC-005612 10-TCS-04006 00505-QRG11-MAT...
Page 48: Key Information
Keep the plate in a safe place such as your wallet, not in the vehicle. In the event that a key is lost, a new key can be made by your Toyota dealer using the key number plate. (→P. 427) ■...
Page 49 1-1. Key information NOTICE ■ To prevent key damage ● Do not subject the keys to strong shocks, expose them to high tempera- tures by placing them in direct sunlight, or get them wet. ● Do not expose the keys to electromagnetic materials or attach any mate- rial that blocks electromagnetic waves to the key surface.
Page 50: Wireless Remote Control
1-2. Opening, closing and locking the doors ∗ Wireless remote control The wireless remote control can be used to lock and unlock the vehi- cle from outside the vehicle. Locks all doors Sounds an alarm (press and hold) Unlocks doors Pressing the button unlocks the driver’s door.
Page 51 When the wireless key battery is depleted ● If window tint with a metallic content or metallic objects are attached to the rear window ■ Customization that can be configured at Toyota dealer Settings (e.g. operation signal) can be changed. (Customizable features →P. 472)
Page 52 1-2. Opening, closing and locking the doors ■ Certification for wireless remote control For vehicles sold in the U.S.A. NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 53: Doors
1-2. Opening, closing and locking the doors Doors The vehicle can be locked and unlocked using the wireless remote control, key or door lock switch. ■ Wireless remote control (if equipped) →P. 26 ■ Locks the door Unlocks the door Vehicles with power door lock system: Turning the key locks and unlocks all doors.
Page 54 1-2. Opening, closing and locking the doors ■ Inside lock button Unlocks the door Locks the door The front doors can be opened by pulling the inside handle even if the lock buttons are in the lock position. Rear door child-protector lock The door cannot be opened from inside the vehicle when the locks are set.
Page 55 1-2. Opening, closing and locking the doors Automatic door locking and unlocking systems (vehicles with power door lock system) The following functions can be set or cancelled: Function Operation Shift position linked Shifting the shift lever out of P locks all door locking function doors.
Page 56 1-2. Opening, closing and locking the doors ■ Setting and canceling the functions To switch between set and canceled, follow the procedure below: Close all the doors and switch the engine switch to the “ON” STEP position. (Perform step 2 within 10 seconds.) Shift the shift lever to P or N, and STEP press and hold the driver's door...
Page 57 The doors cannot be locked when The key is in the engine switch and either of the front door is open. ■ Customization that can be configured at Toyota dealer Settings (e.g. unlocking function using a key) can be changed. (Customizable features →P. 472) CAUTION ■...
Page 58: Back Door
1-2. Opening, closing and locking the doors Back door The back door can be locked and unlocked using the wireless remote control or key. Wireless remote control (if equipped) →P. 26 Locks the back door Unlocks the back door Opens the back door ■...
Page 59 1-2. Opening, closing and locking the doors CAUTION ■ Caution while driving ● Keep the back door closed while driving. If the back door is left open, it may hit nearby objects while driving or lug- gage may be unexpectedly thrown out, causing an accident. In addition, exhaust gases may enter the vehicle, causing death or a seri- ous health hazard.
Page 60 Doing so may cause hands to be caught or the back door damper stay to break, causing an accident. ● Do not attach any accessories other than genuine Toyota parts to the back door. Such additional weight on the back door may cause the back door to fall closed again after it is opened.
Page 61 Do not touch the damper stay rod with gloves or other fabric items. ● Do not attach any accessories other than genuine Toyota parts to the back door. ● Do not place your hand on the damper stay or apply lateral forces to it.
Page 62: Adjustable Components
1-3. Adjustable components (seats, mirrors, steering wheel) Front seats Seat position adjustment lever Seatback angle adjustment lever Vertical height adjustment lever (driver’s side only) Folding down the front passenger's seat (vehicles with seatback table) Move the seat rearward. STEP...
Page 63 1-3. Adjustable components (seats, mirrors, steering wheel) Lower the head restraint and fix STEP the seatback at the most upright lock position. Pull up either seatback lock STEP release knob beside the seat- back and fold the seatback down. Active head restraints When occupant’s back...
Page 64 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Active head restraints Even small forces applied to the seatback may cause the head restraint to move. Pushing up a locked head restraint forcibly may appear the head restraint inner structure. These do not indicate problems. During rear-end collision...
Page 65 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ After returning the seatback to the upright position (vehicles with seat- back table) Make sure the seatback is securely locked by pressing forward and rear- ward on the top of the seatback. Failure to do so will prevent seat belt from operating properly.
Page 66: Rear Seats
1-3. Adjustable components (seats, mirrors, steering wheel) Rear seats The seatbacks of the rear seats can be folded down. Stow the rear outside seat belt STEP buckles and move the rear center seat belt buckle as shown. Lower the head restraints to STEP the lowest position.
Page 67 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ After returning the seatback to the upright position Observe the following precautions. Failure to do so may result in death or serious injury. ● Make sure that the seatback is securely locked in position by lightly rocking it back and forth.
Page 68: Head Restraints
1-3. Adjustable components (seats, mirrors, steering wheel) Head restraints Head restraints are provided for all seats. Pull the head restraints up. Down Lock release Push the head restraint down button while pushing the lock release button. ■ Removing the head restraints Pull the head restraint up while pushing the lock release button.
Page 69 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Adjusting the height of the head restraints Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears. ■ Adjusting the rear center seat head restraint Always raise the head restraint one level from the stowed position when using.
Page 70: Seat Belts
1-3. Adjustable components (seats, mirrors, steering wheel) Seat belts Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. ■ Correct use of the seat belts ● Extend the shoulder belt so that it comes fully over the shoulder, does come into contact with the...
Page 71 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Adjusting the height of the belt (front seats) Push the seat belt shoulder anchor down while pressing the release button. Push the seat belt shoulder anchor up. Move the height adjuster up and down as needed.
Page 72 ■ Seat belt extender If your seat belts cannot be fastened securely because they are not long enough, personalized seat belt extender is available from your Toyota dealer free of charge.
Page 73 Each seat belt should be used by one person only. Do not use a seat belt for more than one person at once, including children. ● Toyota recommends that children be seated in the rear seat and always use a seat belt and/or an appropriate child restraint system. ●...
Page 74 ● Ensure that the belt and tab are locked and the belt is not twisted. If the seat belt does not function correctly, immediately contact your Toyota dealer. ● Replace the seat assembly, including the belts, if your vehicle has been involved in a serious accident, even if there is no obvious damage.
Page 75 1-3. Adjustable components (seats, mirrors, steering wheel) NOTICE ■ When using a seat belt extender When releasing the seat belt, press on the buckle release button on the extender, not on the seat belt. This helps prevent damage to the vehicle interior and the extender itself.
Page 76: Steering Wheel
1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel The steering wheel can be adjusted to a comfortable position. Hold the steering wheel and STEP press the lever down. Adjust to the ideal position by STEP moving the steering wheel horizontally and vertically.
Page 77: Anti-Glare Inside Rear View Mirror
1-3. Adjustable components (seats, mirrors, steering wheel) Anti-glare inside rear view mirror Glare from the headlights of vehicles behind can be reduced by using the following functions. Manual anti-glare inside rear view mirror Normal position Anti-glare position Auto anti-glare inside rear view mirror In automatic mode, sensors are used to detect the headlights of vehicles behind and the reflected light is automatically reduced.
Page 78 1-3. Adjustable components (seats, mirrors, steering wheel) Adjusting the height of the rear view mirror Adjust the height of the rear view mirror by moving it up and down. ■ To prevent sensor error To ensure that the sensors operate prop- erly, do not touch or cover them.
Page 79: Outside Rear View Mirrors
1-3. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors Mirror angle can be adjusted using the switch. Select a mirror to adjust. STEP Left Right Adjust the mirror. STEP Right Down Left Folding back the mirrors Push backward to fold the mir- rors.
Page 80 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Mirror angle can be adjusted when The engine switch is in the “ACC” or “ON” position. ■ When the mirrors are fogged up (vehicles with outside rear view mirror defoggers) Turn on the mirror defoggers to defog the mirrors. (→P. 179) CAUTION ■...
Page 81: Opening And Closing The Windows
1-4. Opening and closing the windows ∗ Power windows The power windows can be opened and closed using the following switches. Closing Opening One-touch opening (driver’s window only) Pressing the switch in the opposite direction will stop win- dow travel partway. Lock switch Press the switch down to lock the passenger window switches.
Page 82 1-4. Opening and closing the windows CAUTION ■ Closing the windows Observe the following precautions. Failing to do so may result in death or serious injury. ● Check to make sure that all passengers do not have any part of their body in a position where it could be caught when a window is being operated.
Page 83: Moon Roof
1-4. Opening and closing the windows ∗ Moon roof Use the overhead switches to open, close, and tilt the moon roof up and down. ■ Opening and closing Open* The moon roof stops slightly before the fully opened posi- tion. Push the switch again to fully open.
Page 84 1-4. Opening and closing the windows ■ The moon roof can be operated when The engine switch is in the “ON” position. ■ Operating the moon roof after turning the engine OFF The moon roof can be operated for approximately 45 seconds after the engine switch is turned to the “ACC”...
Page 85 1-4. Opening and closing the windows CAUTION ■ Opening the moon roof Observe the following precautions. Failing to do so may cause death or serious injury. ● Do not allow any passengers to put their hands or heads outside the vehi- cle while it is moving.
Page 86: Refueling Opening The Fuel Tank Cap
1-5. Refueling Opening the fuel tank cap Perform the following steps to open the fuel tank cap. ■ Before refueling the vehicle Turn the engine switch OFF and ensure that all the doors and windows are closed. ■ Opening the fuel tank cap Pull up the fuel filler door STEP opener.
Page 87 1-5. Refueling Closing the fuel tank cap When replacing the fuel tank cap, turn it until a clicking sound is heard. After releasing your hand, the cap will turn slightly to the opposite direction. ■ Fuel type Unleaded gasoline (Octane rating 87 [Research Octane Number 91] or higher) ■...
Page 88 This may cause static electricity to build up, resulting in a possible ignition hazard. ■ When replacing the fuel cap Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.
Page 89 1-5. Refueling NOTICE ■ Refueling Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the exhaust systems to operate abnormally or damaging fuel system components or the vehicle's painted surface.
Page 90: Theft Deterrent System
1-6. Theft deterrent system Engine immobilizer system The vehicle's keys have built-in transponder chips that prevent the engine from starting if the key has not been previously registered in the vehicle's on-board computer. Never leave the keys inside the vehicle when you leave the vehicle. The indicator light flashes after the key has been removed from the engine switch to indi-...
Page 91 1-6. Theft deterrent system ■ Certifications for the engine immobilizer system (for vehicles sold in Canada) Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.
Page 92: Theft Prevention Labels (Except For Canada)
1-6. Theft deterrent system Theft prevention labels (except for Canada) These labels are attached to the vehicle to reduce vehicle theft by facilitating the tracing and recovery of parts from sto- len vehicles. Do not remove under penalty of law.
Page 93: Safety Information
1-7. Safety information Correct driving posture Drive in a good posture as follows: Sit upright and well back in the seat. (→P. 38) Adjust the position of the seat forward or backward to ensure the pedals can be reached easily depressed to the extent required.
Page 94 1-7. Safety information CAUTION ■ While driving ● Do not adjust the position of the driver's seat while driving. Doing so could cause the driver to lose control of the vehicle. ● Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger.
Page 95: Srs Airbags
1-7. Safety information SRS airbags The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury. Front airbags Driver airbag and front passenger airbag Can help protect the head and chest of the driver and front pas-...
Page 96 1-7. Safety information Airbag system components Front airbag sensors SRS warning light Front passenger occupant Front passenger’s seat belt classification system (ECU buckle switch and sensors) Airbag sensor assembly Side and curtain shield air- Curtain shield airbag sen- bag sensors sors Front passenger airbag Driver airbag...
Page 97 1-7. Safety information The main SRS airbag system components are shown above. The SRS airbag system is controlled by the airbag sensor assembly. The airbag sensor assembly consists of a safing sensor and an airbag sensor. In certain types of severe frontal or side impacts, the SRS airbag sys- tem triggers the airbag inflators.
Page 98 1-7. Safety information ■ If the SRS airbags deploy (inflate) ● Bruising and slight abrasions may result from contact with a deploying (inflating) SRS airbag. ● A loud noise and white powder will be emitted. ● Parts of the airbag module (steering wheel hub, airbag cover and inflator) as well as the front seats, and parts of the front and rear pillars and roof side rail, may be hot for several minutes.
Page 99 1-7. Safety information ■ SRS airbag deployment conditions (SRS side airbags and curtain shield airbags) ● The SRS side airbags and curtain shield airbags will deploy in the event of an impact that exceeds the set threshold level (the level of force corre- sponding to the impact force produced by an approximately 3300 lb.
Page 100 1-7. Safety information ● Collision from the side ● Collision from the rear ● Vehicle rollover ■ Types of collisions that may not deploy the SRS side airbags and cur- tain shield airbags The SRS side airbags and curtain shield airbag system may not activate if the vehicle is subjected to a collision from the side at certain angles, or a col- lision to the side of the vehicle body other than the passenger compartment.
Page 101 1-7. Safety information ■ When to contact your Toyota dealer In the following cases, contact your Toyota dealer as soon as possible. ● Any of the SRS airbags have been inflated. ● The front of the vehicle is damaged or...
Page 102 1-7. Safety information CAUTION ■ SRS airbag precautions Observe the following precautions regarding the airbags. Failure to do so may cause death or serious injury. ● The driver and all passengers in the vehicle must wear their seat belts properly. The SRS airbags are supplemental devices to be used with the seat belts.
Page 103 An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are the safest for infants and children.
Page 104 1-7. Safety information CAUTION ■ SRS airbag precautions ● Do not allow a child to stand in front of the SRS front passenger airbag unit or sit on the knees of a front passenger. ● Do not drive the vehicle while the driver or passenger has items resting on their knees.
Page 105 1-7. Safety information CAUTION ■ SRS airbag precautions ● Do not attach anything to areas such as the door, windshield glass, side door glass, front and rear pillars, roof side rail or assist grip. ● Do not hang coat hangers or other hard objects on the coat hooks.
Page 106 If the areas where the SRS airbags are stored, such as the steering wheel pad and front and rear pillar garnishes, are damaged or cracked, have them replaced by your Toyota dealer. ■ Modification and disposal of SRS airbag system components Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer.
Page 107: Front Passenger Occupant Classification System
1-7. Safety information Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the front passen- ger seat and activates or deactivates the devices for the front passenger.
Page 108 1-7. Safety information Conditions and operation of the front passenger occupant classification system ■ Adult “AIR BAG ON” and “AIR BAG OFF” indicator “AIR BAG lights ON” Indicator/ SRS warning light warning light Front passenger’s seat belt reminder light Flashing Front passenger airbag Side airbag on the front passenger seats...
Page 109 1-7. Safety information ■ Unoccupied “AIR BAG ON” and “AIR BAG OFF” indicator Not illuminated lights Indicator/ warning light SRS warning light Front passenger’s seat belt reminder light Front passenger airbag Deactivated Side airbag on the front passenger seats Devices Curtain shield airbag in the front Activated passenger side...
Page 110 1-7. Safety information : Never install a rear-facing child restraint system on the front pas- senger seat. A forward-facing child restraint system should only be installed on the front passenger seat when it is unavoidable. (→P. 88) : In case the indicator is not illuminated, consult this manual as for installing the child restraint system properly.
Page 111 Do not kick the front passenger seat or subject it to severe impact. Other- wise, the SRS warning light may come on to indicate a malfunction of the detection system. In this case, contact your Toyota dealer immediately. ● Child restraint systems installed on the rear seat should not contact the front seatbacks.
Page 112: Child Restraint Systems
1-7. Safety information Child restraint systems A child restraint system for a small child or baby must be properly restrained on the seat with the lap portion of the lap/shoulder belt. The laws of all 50 states of U.S.A. and Canada now require the use of child restraint systems.
Page 113 1-7. Safety information Types of child restraints Child restraint systems are classified into the following 3 types according to the age and size of the child. Rear facing ⎯ Infant seat/convertible seat Forward facing ⎯ Convertible seat Booster seat...
Page 114 ● Toyota strongly urges the use of a proper child restraint system that con- forms to the size of the child, installed on the rear seat. According to acci- dent statistics, the child is safer when properly restrained in the rear seat than in the front seat.
Page 115 1-7. Safety information CAUTION ■ Child restraint precautions ● Do not use the seat belt extender when installing a child restraint system on the front or rear passenger seat. If installing a child restraint system with the seat belt extender connected to the seat belt, the seat belt will not securely hold the child restraint system, which could cause death or seri- ous injury to the child or other passengers in the event of a sudden stop, sudden swerve or accident.
Page 116: Installing Child Restraints
1-7. Safety information Installing child restraints Follow the child restraint system manufacturer's instructions. Firmly secure child restraints to the rear seats using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder belt can be used if your child restraint system is not compatible with the LATCH (Lower Anchors and Tethers for Chil- dren) system.
Page 117 1-7. Safety information Installation with LATCH system Type A Widen the gap between STEP the seat cushion and seatback slightly. Latch the hooks of the STEP lower straps onto the LATCH anchors. If the child restraint has a STEP top tether strap, the top tether strap should be latched onto...
Page 118 1-7. Safety information Type B Widen the gap between STEP the seat cushion and seatback slightly. Latch the buckles onto STEP the LATCH anchors. If the child restraint has a STEP top tether strap, the top tether strap should be latched onto tether strap anchors.
Page 119 1-7. Safety information Installing child restraints using a seat belt (child restraint lock function belt) Rear facing ⎯ Infant seat/convertible seat ■ Place the child seat on the rear STEP seat facing the rear of the vehi- cle. Run the seat belt through the STEP child seat and insert the plate into the buckle.
Page 120 1-7. Safety information While pushing the child seat STEP down into the rear seat, allow the shoulder belt to retract until the child seat is securely in place. After shoulder belt retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.
Page 121 1-7. Safety information While pushing the child seat into STEP the rear seat, allow the shoulder belt to retract until the child seat is securely in place. After shoulder belt retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.
Page 122 1-7. Safety information Removing a child restraint installed with a seat belt Push the release button and fully retract the seat belt.
Page 123 1-7. Safety information Child restraint systems with a top tether strap Secure the child restraint using STEP the seat belt or the lower anchors, and remove the head restraint. Open the anchor bracket cover, STEP latch the hook onto the anchor bracket and tighten the top tether strap.
Page 124 1-7. Safety information CAUTION ■ When installing a booster seat Do not fully extend the shoulder belt to prevent the belt from going to ALR lock mode: (→P. 47) ALR mode causes the belt to tighten only which could cause injury or dis- comfort to the child.
Page 125 1-7. Safety information CAUTION ■ When installing a child restraint system ● When a booster seat is installed, always ensure that the shoulder belt is positioned across the center of the child's shoulder. The belt should be kept away from the child's neck, but not so that it could fall off the child's shoulder.
Page 126 1-7. Safety information...
Page 127: Driving Procedures
2-1. Driving procedures Driving the vehicle The following procedures should be observed to ensure safe driv- ing. ■ Starting the engine →P. 115 ■ Driving Automatic transmission With the brake pedal depressed, shift the shift lever to D. STEP (→P. 119) Release the parking brake.
Page 128 2-1. Driving procedures ■ Parking the vehicle Automatic transmission With the shift lever in D, depress the brake pedal. STEP Set the parking brake. (→P. 127) STEP Shift the shift lever to P. (→P. 119) STEP When parking on a hill, if necessary, block the wheels. Turn the engine switch to the “LOCK”...
Page 129 ■ Breaking in your new Toyota To extend the life of the vehicle, the following precautions are recommended to observe: ●...
Page 130 Your vehicle has a drum-in-disc type parking brake system. This type of brake system needs bedding-down of the brake shoes periodically or when- ever the parking brake shoes and/or drum are replaced. Have your Toyota dealer perform the bedding down.
Page 131 Large amounts of exhaust in the vehi- cle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the vehicle inspected by your Toyota dealer immediately. ●...
Page 132 2-1. Driving procedures CAUTION ● Do not drive the vehicle off-road. This is not a AWD vehicle designed for real off-road driving. Proceed with all due caution if it becomes unavoidable to drive off-road. ● Do not drive across river crossings or through other bodies of water. This may cause electric/electronic components to short circuit, damage the engine or cause other serious damage to the vehicle.
Page 133 2-1. Driving procedures CAUTION ● Vehicles with an automatic transmission: In order to prevent accidents due to the vehicle rolling away, always keep depressing the brake pedal while the engine is running, and apply the parking brake as necessary. ● If the vehicle is stopped on an incline, in order to prevent accidents caused by the vehicle rolling forward or backward, always depress the brake pedal and securely apply the parking brake as needed.
Page 134 The exhaust should be checked occasionally. If there is a hole or crack caused by corrosion, damage to a joint or abnormal exhaust noise, be sure to have the vehicle inspected and repaired by your Toyota dealer. Failure to do so may allow exhaust gases to enter the vehicle, resulting in death or a serious health hazard.
Page 135 2-1. Driving procedures CAUTION ■ When braking the vehicle ● When the brakes are wet, drive more cautiously. Braking distance increases when the brakes are wet, and may cause one side of the vehicle to brake differently than the other side. Also the parking brake may not securely hold the vehicle.
Page 136 2-1. Driving procedures NOTICE ■ When driving the vehicle ● Do not depress the accelerator and brake pedals at the same time during driving. If the brake pedal is depressed while driving with the accelerator pedal depressed, driving torque may be restrained. Manual transmission ●...
Page 137 If you hear a squealing or scraping noise (brake pad wear limit indica- tors) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. Rotor damage can result if the pads are not replaced when needed.
Page 138: Engine (Ignition) Switch
2-1. Driving procedures Engine (ignition) switch ■ Starting the engine Automatic transmission Check that the parking brake is set. STEP Check that the shift lever is set in P. STEP Sit in the driver’s seat and firmly depress the brake pedal. STEP Turn the engine switch to the “START”...
Page 139 2-1. Driving procedures ■ Changing engine switch position “LOCK” The steering wheel is locked and the key can be removed. (Vehicles with an automatic transmission: The key can be removed only when the shift lever is in P.) “ACC” Some electrical components such as the audio system can be used.
Page 140 2-1. Driving procedures ■ Turning the engine switch from “ACC” to “LOCK” Shift the shift lever to P (auto- STEP matic transmission) or N (man- ual transmission). (→P. 119, 124) Push in the key and turn to the STEP “LOCK” position. ■...
Page 141 2-1. Driving procedures NOTICE ■ To prevent battery discharge Do not leave the key in the “ACC” or “ON” position for long periods if the engine is not running. ■ When starting the engine 2.4 L 4-cylinder (2AZ-FE) engine ⎯ Do not crank for more than 30 sec- ●...
Page 142: Automatic Transmission
2-1. Driving procedures ∗ Automatic transmission Select a shift position appropriate for the driving conditions. ■ Shifting the shift lever Standard type Multi-mode type While the engine switch is in the “ON” position, depress the brake pedal and move the shift lever. ∗...
Page 143 2-1. Driving procedures ■ Shift position uses Function Shift position Standard type Multi-mode type Parking the vehicle or starting the engine Reversing Neutral Normal driving S mode driving (→P. 121) Position for engine braking Position for more powerful engine braking Position for maximum engine braking : Shifting to the D position allows the system to select a gear suitable...
Page 144 2-1. Driving procedures Changing shift ranges in S mode (multi-mode type) Shift the shift lever to the S position and operate the shift lever. Upshifting Downshifting The initial shift range in S mode is automatically set to 4 or 5. How- ever, the initial shift range may be set to 3 if AI-SHIFT has operated while the shift lever was in the D position.
Page 145 2-1. Driving procedures ■ Shift ranges and their functions Shift range Function A gear between 1 and 5 is automatically selected according to vehicle speed and driving conditions. A gear between 1 and 4 is automatically selected according to vehicle speed and driving conditions. A gear between 1 and 3 is automatically selected according to vehicle speed and driving conditions.
Page 146 If the “S” indicator does not come on even after shifting the shift lever to S (multi-mode type) This may indicate a malfunction in the automatic transmission system. Have the vehicle inspected by your Toyota dealer immediately. (In this situation, the vehicle will operate as if the shift lever is in D.) ■...
Page 147: Manual Transmission
2-1. Driving procedures ∗ Manual transmission ■ Shifting the shift lever Fully depress the clutch pedal before operating shift lever, and then release the clutch pedal slowly. ■ Maximum allowable speeds Observe the following maximum allowable speeds in each gear when maxi- mum acceleration is necessary.
Page 148 2-1. Driving procedures 2.4 L 4-cylinder (2AZ-FE) engine (with double wishbone rear suspension) mph (km/h) Shift position Maximum speed 31 (50) 54 (87) 83 (134) 113 (183) 1.8 L 4-cylinder (2ZR-FE) engine mph (km/h) Shift position Maximum speed 34 (55) 56 (91) 82 (132) 121 (195)
Page 149: Turn Signal Lever
2-1. Driving procedures Turn signal lever Right turn Left turn Move and hold the lever partway to signal a lane change. The right hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change.
Page 150: Parking Brake
2-1. Driving procedures Parking brake U.S.A. Canada Sets the parking brake Fully set the parking brake while depressing the brake pedal. Releases the parking brake Slightly raise the lever and lower it completely while pressing the but- ton. ■ Usage in winter time See “Winter driving tips”...
Page 151: Horn
2-1. Driving procedures Horn To sound the horn, press on or close to the mark. ■ After adjusting the steering wheel Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. (→P.
Page 152: Instrument Cluster Gauges And Meters
2-2. Instrument cluster Gauges and meters The following gauges, meters and displays illuminate when the engine switch is in the “ON” position. Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank. Outside temperature display Displays the outside air temperature.
Page 153 2-2. Instrument cluster Engine coolant temperature gauge Displays the engine coolant temperature. Automatic transmission shift position indicator lights (if equipped) →P. 119 Odometer and trip meter Odometer: Displays the total distance the vehicle has been driven. Trip meter: Displays the distance the vehicle has been driven since the meter was last reset.
Page 154 2-2. Instrument cluster Instrument panel light control The brightness of the instrument panel lights can be adjusted. Darker Brighter When the headlight switch is turned on, the brightness will be reduced slightly unless the con- trol button is turned fully clock- wise.
Page 155: Indicators And Warning Lights
2-2. Instrument cluster Indicators and warning lights The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems. Instrument cluster Center panel...
Page 156 There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer for details.
Page 157 There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer for details.
Page 158: Operating The Lights And Wipers
2-3. Operating the lights and wipers Headlight switch The headlights can be operated manually. The daytime running lights turn on. side marker, parking, tail, license plate, daytime run- ning lights and instru- U.S.A. Canada ment panel lights turn The headlights and all lights listed above (except daytime run- ning lights) turn on.
Page 159 2-3. Operating the lights and wipers Turning on the high beam headlights With the headlights on, push the lever forward to turn on the high beams. Pull the lever back to the center position to turn the high beams off. Pull the lever toward you to turn on the high beams.
Page 160: Fog Light Switch
2-3. Operating the lights and wipers ∗ Fog light switch The fog lights improve visibility in difficult driving conditions, such as in rain or fog. They can be turned on only when the headlights are on low beam. Front fog lights on ∗...
Page 161: Windshield Wipers And Washer
2-3. Operating the lights and wipers Windshield wipers and washer Wiper can be operated manually. Intermittent windshield wiper operation Low speed windshield wiper operation High speed windshield wiper operation Temporary operation Increases the intermittent windshield wiper frequency* Decreases the intermittent windshield wiper frequency* If equipped Wash/wipe operation...
Page 162 2-3. Operating the lights and wipers ■ The windshield wipers and washers can be operated when The engine switch is in the “ON” position. ■ If no windshield washer fluid sprays Check that the washer nozzles are not blocked and if there is washer fluid in the windshield washer fluid reservoir.
Page 163: Rear Window Wiper And Washer
2-3. Operating the lights and wipers ∗ Rear window wiper and washer Intermittent window wiper operation Normal window wiper oper- ation Washer/wiper dual opera- tion Wiper operate automatically. Washer/wiper dual opera- tion Wiper operate automatically. ■ The rear window wiper and washer can be operated when The engine switch is in “ON”.
Page 164: Using Other Driving
2-4. Using other driving systems ∗ Cruise control Use the cruise control to maintain a set speed without depressing the accelerator pedal. Indicators Cruise control switch ■ Setting the vehicle speed Press the “ON-OFF” button to STEP activate the cruise control. Press the button again to deactivate the cruise control.
Page 165 2-4. Using other driving systems ■ Adjusting the speed setting To change the set speed, operate the lever until the desired set speed is obtained. Increases the speed Decreases the speed Fine adjustment: Momentarily move the lever in the desired direction.
Page 166 2-4. Using other driving systems ■ Canceling and resuming the constant speed control Pulling the lever toward you cancels the constant speed control. The speed setting is also can- celed when the brakes are applied or the clutch pedal (manual transmission only) is depressed.
Page 167 If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer. CAUTION ■...
Page 168: Driving Assist Systems
2-4. Using other driving systems Driving assist systems To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. ■...
Page 169 2-4. Using other driving systems When VSC and TRAC are operating If the vehicle is in danger of slip- ping or the front wheels (2WD), or 4 wheels (AWD) spin, the indi- cator flashes to indicate that VSC/TRAC have been engaged. A buzzer (intermittent) sounds to indicate that VSC is operating.
Page 170 • The brake pedal may pulsate slightly after ABS is activated. • The brake pedal may move down slightly after ABS is activated. ■ If the slip indicator light comes on There is a malfunction in the TRAC and VSC systems. Contact your Toyota dealer and have your Toyota inspected.
Page 171 2-4. Using other driving systems ■ EPS operation sound When the steering wheel operates, a motor sound (whirring sound) may be heard. This does not indicate a malfunction. ■ Reduced effectiveness of EPS The effectiveness of EPS is reduced to prevent the system from overheating when there is frequent steering input over an extended period of time.
Page 172 The ABS and VSC systems will not function correctly if different tires are fit- ted on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels. ■ Handling of tires and suspension Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause the system to malfunction.
Page 173: Driving Information Cargo And Luggage
2-5. Driving information Cargo and luggage Take notice of the following information about storage precau- tions, cargo capacity and load. ● Stow cargo and luggage in the luggage compartment whenever possible. Be sure all items are secured in place. ● Be careful to keep the vehicle level. Placing the weight as far for- ward as possible helps maintain vehicle balance.
Page 174 2-5. Driving information (6)If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (→P. 159) Example on your vehicle Cargo capacity Total load capacity...
Page 175 2-5. Driving information CAUTION ■ Storage precautions Observe the following precautions. Failing to do so may result in death or serious injury. ● To prevent cargo and luggage from sliding forward during braking, do not stack anything in the luggage compartment. Keep cargo and lug- gage low, as close to the floor as possible.
Page 176: Vehicle Load Limits
150 lb. (68 kg) per person. ■ Towing capacity 1.8 L 4-cylinder (2ZR-FE) engine Toyota does not recommend towing a trailer with your vehicle. 2.4 L 4-cylinder (2AZ-FE) engine 1500 lb. (680 kg) ■ Cargo capacity Cargo capacity may increase or decrease depending on the weight and the number of occupants.
Page 177: Winter Driving Tips
2-5. Driving information Winter driving tips Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations ● Use fluids that are appropriate to the prevailing outside tem- peratures.
Page 178 2-5. Driving information ■ When driving the vehicle Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions. ■ When parking the vehicle Park the vehicle and move the shift lever to P (automatic trans- mission), 1 or R (manual transmission) without setting the park- ing brake.
Page 179 2-5. Driving information ■ Snow chain installation (vehicles with 16-inch and 17-inch tires) Observe the following precautions when installing and removing chains. ● Install and remove tire chains in a safe location. ● Install tire chains on the front tires only. Do not install tire chains on rear tires.
Page 180 NOTICE ■ Repairing or replacing snow tires Request repairs of and obtain replacement snow tires from Toyota dealers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.
Page 181: Trailer Towing (1.8 L 4-Cylinder [2Zr-Fe] Engine)
Toyota also does not recommend the installation of a tow hitch or the use of a tow hitch carrier for a wheelchair, scooter, bicycle, etc. Your Toyota is not designed for trailer towing or for the use of tow hitch mounted carriers.
Page 182: Trailer Towing (2.4 L 4-Cylinder [2Az-Fe] Engine)
Towing a trailer will have an adverse effect on handling, perfor- mance, braking, durability, and fuel consumption. For your safety and the safety of others, do not overload the vehicle or trailer. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. ■...
Page 183 Total trailer weight Tongue load Towing a trailer Contact your Toyota dealer for further information about additional requirements such as a towing kit, etc. Hitch Trailer hitch assemblies have different weight capacities established by the hitch manufacturer.
Page 184 ■ Break-in schedule Toyota recommends that you do not use a new vehicle or a vehicle with any new power train components (engine, transmission, differential, wheel bear- ings, etc.) to tow a trailer for the first 500 miles (800 km) of driving.
Page 185 40% in the rear. ■ Hitches ● If you wish to install a trailer hitch, contact your Toyota dealer. ● Use only a hitch that conforms to the total trailer weight requirement. ● Follow the directions supplied by the hitch manufacturer.
Page 186 ■ When installing a trailer hitch ● Use only the position recommended by your Toyota dealer. Do not install the trailer hitch on the bumper; this may cause body damage. ● Do not use axle-mounted hitches, as they can cause damage to the axle housing, wheel bearings, wheels or tires.
Page 187 2-5. Driving information ● Reversing with a trailer attached is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left. Move your hand to the right to move the trailer to right.
Page 188 2-5. Driving information ● To maintain engine braking efficiency and charging system perfor- mance when using engine braking, do not use 5th gear (manual transmission), or do not put the transmission in “D” (automatic transmission). ● Due to the added load of the trailer, your vehicle's engine may overheat on hot days (at temperatures over 85°F [30°C]) when driving up a long or steep grade.
Page 189 2-5. Driving information ● When restarting after parking on a slope: With the transmission in the P position (automatic transmis- STEP sion) or the clutch pedal (manual transmission) depressed, start the engine. On vehicles with an automatic transmission, be sure to keep the brake pedal pressed. Shift into a forward gear.
Page 190: Dinghy Towing (Automatic Transmission)
2-5. Driving information Dinghy towing (automatic transmission) Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home. NOTICE ■ To avoid serious damage to your vehicle Do not tow your vehicle with 4 wheels on the ground.
Page 191: Dinghy Towing (Manual Transmission)
2-5. Driving information Dinghy towing (manual transmission) Your vehicle can be dinghy towed in a forward direction (with 4 wheels on the ground) behind a motor home. Towing your vehicle with 4 wheels on the ground To prevent damage to your vehicle, perform the following procedures before towing.
Page 192 2-5. Driving information NOTICE ■ Dinghy towing direction Do not tow the vehicle backwards. Doing so may cause serious damage. ■ To prevent the steering from locking Ensure the engine switch is in the “ACC” position.
Page 193: Using The Air Conditioning
3-1. Using the air conditioning system and defogger Air conditioning system Heater Air outlet selection dial Temperature control dial Fan speed control dial Air intake mode switch Air conditioning system Air outlet selection dial Temperature control dial Fan speed control dial Air intake mode switch Air conditioning ON/OFF switch...
Page 194 3-1. Using the air conditioning system and defogger Adjusting the settings ■ Adjusting the temperature setting (heater) Turn the temperature control dial clockwise to increase the temper- ature. ■ Adjusting the temperature setting (air conditioning system) Turn the temperature control dial clockwise (warm) or counter- clockwise (cool).
Page 195 3-1. Using the air conditioning system and defogger Air flows to the upper body and feet. : Some models Mainly air flows to the feet. : Some models Air flows to the feet and the windshield defogger operates. The air intake is automatically switched to outside air mode.
Page 196 3-1. Using the air conditioning system and defogger Air flows to the windshield and side windows. The air intake is automatically switched to outside air mode. It is not possible to return to recircu- lated air mode when the switch is ■...
Page 197 3-1. Using the air conditioning system and defogger Adjusting the position of and opening and closing the air outlets Adjusting the position Direct air flow to the left or right, up or down. Opening and closing Open the vent Close the vent...
Page 198 3-1. Using the air conditioning system and defogger ■ For quick cooling (vehicles with air conditioning system) Turn the temperature control dial to the “MAX A/C” position and select the recirculated air mode. ■ For quick clearing of the windshield and side windows (vehicles with air conditioning system) Press to turn the air conditioning on.
Page 199 3-1. Using the air conditioning system and defogger NOTICE ■ To prevent battery discharge Do not leave the air conditioning system on longer than necessary when the engine is stopped.
Page 200: Rear Window And Outside Rear View Mirror Defoggers
3-1. Using the air conditioning system and defogger Rear window and outside rear view mirror defoggers Clear the rear window using the defogger. On/off The defoggers will automati- cally turn off after approxi- mately 15 minutes. ■ Outside rear view mirror defogger (if equipped) Turning the rear window defogger on will turn the outside rear view mirror defoggers on.
Page 201: Using The Audio System
3-2. Using the audio system Audio system types Type A: CD player and AM/FM radio (with CD changer controller) Type B: CD player and AM/FM radio (with CD changer controller)
Page 202 3-2. Using the audio system Title Page Using the radio P. 183 Using the CD player P. 190 Playing MP3 and WMA discs P. 197 Operating an iPod P. 206 Operating a USB memory P. 213 Optimal use of the audio system P.
Page 203 3-2. Using the audio system CAUTION ■ For vehicles sold in U.S.A. and Canada ● Part 15 of the FCC Rules FCC Warning: Any unauthorized changes or modifications to this equipment will void the user’s authority to operate this device. ●...
Page 204: Using The Radio
3-2. Using the audio system Using the radio Type A Power Volume Adjusting the frequency Station selector Seeking a AM/FM frequency mode buttons Scanning for receivable stations Type B Power Volume Adjusting the frequency (AM, FM mode) or channel (SAT mode) Station selector Changing Seeking a...
Page 205 3-2. Using the audio system ® Setting station presets (excluding XM Satellite Radio) ∧ Search for desired stations by turning or pressing “ ” or STEP “∨” on Press and hold the button (from or one of STEP ) the station is to be set to until you hear a beep. Type B: Each time is pressed, station pages are changed.
Page 206 3-2. Using the audio system ® Satellite Radio (type B only) ® ■ Receiving XM Satellite Radio Press STEP The display changes as follows each time is pressed. AM → FM → XM Turn to select the desired channel from all categories or STEP press “∧”...
Page 207 3-2. Using the audio system ■ Displaying text information Press Each time is pressed, the display changes in the following order: Title (song/program title) → Name (artist name/feature)/Title (song/pro- gram title). ■ Reception sensitivity ● Cargo loaded on the roof luggage carrier, especially metal objects, may ®...
Page 208 3-2. Using the audio system ® ■ Satellite Radio ® An XM Satellite Radio is a tuner designed exclusively to receive broadcasts provided under a separate subscription. Availability is limited to the 48 con- tiguous states and 10 Canadian provinces. ®...
Page 209 ANTENNA securely. CHECK There is a short-circuit in the antenna or the sur- ANTENNA rounding antenna cable. See a Toyota certified dealer. ® You have not subscribed to XM Satellite Radio. The radio is being updated with the latest encryp- ®...
Page 210 3-2. Using the audio system The channel you selected is no longer available. Wait for about 2 seconds until the radio returns to CHANNEL NOT the previous channel or “CH001”. If it does not AVAILABLE change automatically, select another channel. ®...
Page 211: Using The Cd Player
3-2. Using the audio system Using the CD player Type A Power Volume Reverse Fast-forward CD eject Repeat play Displaying text Selecting a track messages Random playback Search playback Playback Type B Power Volume Selector buttons Selecting a track CD eject Selecting a track/ Displaying text...
Page 212 3-2. Using the audio system Loading CDs ■ Loading a CD Insert a CD. Ejecting CDs ■ Ejecting a CD Press and remove the CD. Selecting a track ∧ Press “ ” to move up or “∨” to move down using until the desired track number is displayed.
Page 213 3-2. Using the audio system Selecting a CD (with a CD changer) ■ Selecting a CD to play Press ■ Scanning loaded CDs Press and hold until you hear a beep. STEP The first ten seconds of the first track on each CD will be played. To cancel, press again.
Page 214: Random Playback
3-2. Using the audio system Random playback ■ Current CD Press (RAND) or (RDM). Songs are played in random order. To cancel, press the button once more (without a CD changer), or twice more (with a CD changer). ■ All CDs (with a CD changer) Type A Press and hold (RAND) until you hear a beep.
Page 215 “WAIT” or “PLEASE WAIT”: Operation has stopped due to a high tempera- ture inside the player. Wait for a while and then press . Contact your Toyota dealer if the CD still cannot be played back. ■ Discs that can be used Discs with the marks shown below can be used.
Page 216 3-2. Using the audio system NOTICE ■ CDs and adapters that cannot be used Do not use the following types of CDs, 3 in. (8 cm) CD adapters or Dual Disc. Doing so may damage the CD player and/or the CD insert/eject function. ●...
Page 217 3-2. Using the audio system NOTICE ■ CD player precautions Failure to follow the precautions below may result in serious damage to the CDs or the player itself. ● Do not insert anything other than CDs into the CD slot. ●...
Page 218: Playing Mp3 And Wma Discs
3-2. Using the audio system Playing MP3 and WMA discs Type A Power Volume Fast-forward Selecting a file Reverse CD eject Selecting a file Selecting a folder Playback Repeat play Searching playback Displaying text messages Random playback Type B Power Volume Selecting a file Selector buttons...
Page 219 3-2. Using the audio system Loading and ejecting MP3 and WMA discs →P. 191 Selecting MP3 and WMA discs (with a CD changer) →P. 192 Selecting and scanning a folder ■ Selecting folders one at a time Press “∧” or “∨” on to select the desired folder.
Page 220 3-2. Using the audio system Fast-forwarding and reversing files Type A Press (reverse) or (fast-forward). Type B ∧ Press and hold “ ” or “∨” on Playing and pausing files (type B only) Press Repeat play ■ Repeating a file Press (RPT) or (RPT).
Page 221 3-2. Using the audio system Random playback ■ Playing files from a particular folder in random order Press (RAND) or (RDM). To cancel, press the button once more (without a CD changer), or twice more (with a CD changer). ■ Playing all of the files on a disc in random order Type A Press and hold...
Page 222 “WAIT” or “PLEASE WAIT”: Operation has stopped due to a high tempera- ture inside the player. Wait for a while and then press . Contact your Toyota dealer if the CD still cannot be played. ■ Discs that can be used Discs with the marks shown below can be used.
Page 223 3-2. Using the audio system ■ MP3 and WMA files MP3 (MPEG Audio LAYER3) is a standard audio compression format. Files can be compressed to approximately 1/10 of their original size by using MP3 compression. WMA (Windows Media Audio) is a Microsoft audio compression format. This format compresses audio data to a size smaller than that of the MP3 format.
Page 224 3-2. Using the audio system ● Compatible media Media that can be used for MP3 and WMA playback are CD-Rs and CD- RWs. Playback in some instances may not be possible, depending on the status of the CD-R or CD-RW. Playback may not be possible or the audio may jump if the disc is scratched or marked with fingerprints.
Page 225 3-2. Using the audio system ● ID3 and WMA tags ID3 tags can be added to MP3 files, making it possible to record the track title, artist name, etc. The system is compatible with ID3 Ver. 1.0, 1.1, and Ver. 2.2, 2.3 ID3 tags. (The number of characters is based on ID3 Ver.
Page 226 3-2. Using the audio system NOTICE ■ CDs that cannot be used (→P. 195) ■ CD player precautions (→P. 196)
Page 227: Operating An Ipod
3-2. Using the audio system ∗ Operating an iPod Connecting an iPod enables you to enjoy music from the vehicle speakers. ■ Connecting an iPod Open the cover and connect an iPod using an iPod cable. STEP Turn on the power of the iPod if it is not turned on. Press STEP ∗...
Page 228 3-2. Using the audio system ■ Control panel Power Volume Selector knob Selector buttons Selecting a track/ Displaying text Playback fast-forwarding messages and rewinding Playback/pause...
Page 229 3-2. Using the audio system Selecting a play mode Press (BROWSE) to select iPod menu mode. STEP Press that corresponds to the desired play mode. STEP Pressing (MORE) to change to the second selection list. ■ Play mode list First Second Third Fourth...
Page 230 3-2. Using the audio system ■ Selecting a list Turn to display the first selection list. STEP Press to select the desired item. STEP Repeat the same procedure to select the desired song name. STEP To return to the previous selection list, press Selecting songs from a song list Press (LIST).
Page 231 3-2. Using the audio system Selecting songs Turn or press “∧” or “∨” on to select the desired song. Playing and pausing songs Press Fast-forwarding and rewinding songs ∧ Press and hold “ ” or “∨” on Shuffle playback ■ Playing songs from one playlist or album in random order Press (RDM).
Page 232 3-2. Using the audio system Switching the display Press Each time is pressed, the display changes in the following order: Track title → Track title/Artist name → Track title/Album name → Track title/Elapsed time ■ About iPod ● Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Page 233 3-2. Using the audio system ■ Compatible models Model Generation Software version iPod 5th generation Ver. 1.2.0 or higher iPod nano 1st generation Ver. 1.3.0 or higher 2nd generation Ver. 1.1.2 or higher 3rd generation Ver. 1.0.0 or higher iPod touch 1st generation Ver.
Page 234: Operating A Usb Memory
3-2. Using the audio system ∗ Operating a USB memory Connecting a USB memory enables you to enjoy music from the vehicle speakers. ■ Connecting a USB memory Open the cover and connect a USB memory. STEP Turn on the power of the USB memory if it is not turned on. Press STEP ∗...
Page 235 3-2. Using the audio system ■ Control panel Power Volume Selector knob Selector buttons Selecting a folder Selecting a and file track/ Displaying text Playback fast-forwarding messages and rewinding Searching playback Playback/pause...
Page 236 3-2. Using the audio system Selecting and scanning a folder ■ Selecting a folder Press “∧” or “∨” on to select the desired folder. ■ Returning to the first file of the first folder Press and hold “∨” on until you hear a beep. ■...
Page 237 3-2. Using the audio system Fast-forwarding and rewinding files ∧ Press and hold “ ” or “∨” on Random playback ■ Playing files from a folder in random order Press (RDM). To cancel, press the button twice. ■ Playing all the files from a USB memory in random order Press (RDM) twice.
Page 238 3-2. Using the audio system ■ USB memory functions Depending on the USB memory that is connected to the system, certain functions may not be available. Disconnecting the device and reconnecting it once again may resolve some malfunctions. ■ Error messages “USB ERROR”: This indicates a problem either in the USB memory or inside the USB box or connection between them.
Page 239 3-2. Using the audio system ● MP3 and WMA files MP3 (MPEG Audio LAYER 3) is a standard audio compression format. Files can be compressed to approximately 1/10 of their original size using MP3 compression. WMA (Windows Media Audio) is a Microsoft audio compression format. This format compresses audio data to a size smaller than that of the MP3 format.
Page 240 3-2. Using the audio system ● ID3 and WMA tags ID3 tags can be added to MP3 files, making it possible to record the track title, artist name, etc. The system is compatible with ID3 Ver. 1.0, 1.1, and Ver. 2.2, 2.3, 2.4 ID3 tags.
Page 241 3-2. Using the audio system NOTICE ■ To prevent damage to a USB memory ● Do not leave a USB memory in the vehicle. The temperature inside may become high, resulting in damage to the player. ● Do not push down on or apply unnecessary pressure to the USB memory while it is connected as this may damage the USB memory or its terminal.
Page 242: Optimal Use Of The Audio System
3-2. Using the audio system Optimal use of the audio system Type A Adjusting the sound quality and ASL Type B Adjusting the sound quality and ASL Selector buttons Menu button...
Page 243 3-2. Using the audio system Using the audio control function ■ Changing sound quality modes Type A Pressing selects the mode to be changed in the following order. “BAS”→“TRE”→“FAD”→“BAL”→“ASL” Type B Press STEP Press that corresponds to the desired mode. STEP “BASS”, “TREB”, “FADE”, or “BAL”...
Page 244 3-2. Using the audio system Type B Mode Sound qual- Turn to the Turn to the Level displayed ity mode left right BASS Bass* -5 to 5 High TREB Treble* -5 to 5 Front/rear Shifts to FADE volume F7 to R7 Shifts to rear front balance...
Page 245 3-2. Using the audio system Type B Press STEP Press (MORE). STEP Press (ASL). STEP Press that corresponds to the desired mode (LOW, STEP MID, HIGH or OFF). ASL automatically adjusts the volume and tone quality according to vehicle speed. ■...
Page 246: Using The Aux Port
3-2. Using the audio system Using the AUX port This port can be used to connect a portable audio device and listen to it through the vehicle’s speakers. Type A Open the cover and connect STEP the portable audio device. Press STEP Type B...
Page 247 3-2. Using the audio system Press STEP ■ Operating portable audio devices connected to the audio system The volume can be adjusted using the vehicle's audio controls. All other adjustments must be made on the portable audio device itself. ■ When using a portable audio device connected to the power outlet Noise may occur during playback.
Page 248: Using The Steering Wheel Audio Switches
3-2. Using the audio system Using the steering wheel audio switches Some audio features can be controlled using the switches on the steering wheel. Volume Radio mode: Selects radio stations CD mode: Selects tracks, files (MP3 and WMA) and discs iPod mode: Selects songs USB memory mode: Selects files and fold-...
Page 249 3-2. Using the audio system Changing the audio source Press when the audio system is turned on. The audio source changes as follows each time is pressed. Type A FM→CD→CD changer (with a CD changer)→AUX→AM Type B FM→SAT→CD→CD changer (with a CD changer) ®...
Page 250 3-2. Using the audio system Selecting a track/file or song ® Press to select CD, iPod, USB memory or Bluetooth STEP audio mode. Press “∧” or “∨” on to select the desired track/file or song. STEP Selecting a folder or album ®...
Page 251: Using The Bluetooth
® 3-3. Using the Bluetooth audio system ® ∗ Bluetooth audio system ® The Bluetooth audio system enables you to enjoy music played on a portable digital audio player (portable player) from the vehicle speakers via wireless communication. ® This audio system supports Bluetooth , a wireless data system capable of playing portable audio music without cables.
Page 252 ® 3-3. Using the Bluetooth audio system ■ When transferring ownership of the vehicle Be sure to initialize the system to prevent personal data from being improp- erly accessed. (→P. 273) ® ■ About Bluetooth Bluetooth is a registered trademark of Bluetooth SIG.
Page 253 ® 3-3. Using the Bluetooth audio system CAUTION ■ FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Radio Frequency Radiation Exposure. This equipment complies with FCC/ IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules.
Page 254: Using The Bluetooth ® Audio System
® 3-3. Using the Bluetooth audio system ® Using the Bluetooth audio system ■ Audio unit Display Track title, Artist name, Album name, Elapsed time, “Streaming Audio”, etc. is displayed. Selects items such as menu and number Turn: Selects an item Press: Inputs the selected item Bluetooth-Audio...
Page 255 ® 3-3. Using the Bluetooth audio system ■ Microphone Vehicles with moon roof Vehicles without moon roof...
Page 256 ® 3-3. Using the Bluetooth audio system Operating the system using voice commands By following voice guidance instructions output from the speaker, ® voice commands enable the operation of the Bluetooth audio sys- tem without the need to check the display or operate ■...
Page 257 ® 3-3. Using the Bluetooth audio system ® Using the Bluetooth audio system for the first time ® Before using the Bluetooth audio system, it is necessary to register ® a Bluetooth enabled portable player in the system. Follow the proce- dure below to register (pair) a portable player: Press and hold until “BT AUDIO”...
Page 258 ® 3-3. Using the Bluetooth audio system Input the passkey into the portable player. STEP Refer to the manual that comes with the portable player for the oper- ation of the portable player. Guidance for registration completion is heard. ® If the portable player has a Bluetooth phone, the phone can be reg- istered at the same time.
Page 259 ® 3-3. Using the Bluetooth audio system ■ When using a voice command For numbers, say a combination of single digits from zero to nine. Say the command correctly and clearly. ■ Situations where the system may not recognize your voice ●...
Page 260: Operating A Bluetooth
® 3-3. Using the Bluetooth audio system ® Operating a Bluetooth enabled portable player Power Volume Selector knob Selecting an album Selecting a track/ Displaying text Playback fast-forwarding messages and reversing Playback/pause Selecting an album Press “∨” or “∧” on Selecting tracks Press “∧”...
Page 261 ® 3-3. Using the Bluetooth audio system Fast-forwarding and reversing tracks ∧ Press and hold “ ” or “∨” on Switching the display Press Each time is pressed, the display changes in the following order: Track title → Track title/Artist name → Track title/Album name → Track title/Elapsed time Using the steering wheel audio switches →P.
Page 262: Setting Up A Bluetooth ® Enabled Portable Player
® 3-3. Using the Bluetooth audio system ® Setting up a Bluetooth enabled portable player ® Registering a portable player in the Bluetooth audio system allows the system to function. The following functions can be used for reg- istered portable players: ■...
Page 263 ® 3-3. Using the Bluetooth audio system Registering a portable player Select “Pair Audio Players (Pair audio player)” using a voice com- mand or , and perform the procedure for registering a portable player. (→P. 236) Selecting a portable player to be used Select “Select Audio Player”...
Page 264 ® 3-3. Using the Bluetooth audio system Press the talk switch and say “From car” or “From audio”, and STEP select “Confirm” using a voice command or If “From car” is selected, the portable player will be automatically connected whenever the engine switch is in either the “ACC” or “ON” position.
Page 265 ® 3-3. Using the Bluetooth audio system Listing the registered portable players Select “List Audio Players” using a voice command or . The list of registered portable players will be read aloud. When listing is complete, the system returns to “BT Audio Setup”. Pressing the talk switch while the name of a portable player is being read aloud selects the portable player, and the following functions will become available:...
Page 266 ® 3-3. Using the Bluetooth audio system Deleting a registered portable player Select “Delete Audio Player” using a voice command or STEP Select the portable player to be deleted by either of the follow- STEP ing methods and select “Confirm” using a voice command or a.
Page 267: Bluetooth ® Audio System Setup
® 3-3. Using the Bluetooth audio system ® Bluetooth audio system setup ■ System setup items and operation procedures →P. 271...
Page 268: Using The Hands-Free Phone System
3-4. Using the hands-free phone system (for cellular phone) ∗ Hands-free phone system (for cellular phone) features ® This system supports Bluetooth , which allows you to make or receive calls without using cables to connect a cellular phone and the system, and without operating the cellular phone.
Page 269 3-4. Using the hands-free phone system (for cellular phone) Title Page Using the hands-free phone system ■ Operating the system using a voice command ■ Using the hands-free phone system for P. 252 the first time ■ Menu list of the hands-free phone system Making a phone call ■...
Page 270 3-4. Using the hands-free phone system (for cellular phone) ■ Conditions under which the system will not operate ® ● If using a cellular phone that does not support Bluetooth ● If the cellular phone is switched off ● If you are outside service range ●...
Page 271 3-4. Using the hands-free phone system (for cellular phone) ® ■ About Bluetooth Bluetooth is a registered trademark of Bluetooth SIG. Inc. ■ Certification for the hands-free phone system FCC ID: L2C0045TR IC ID: 3432A-0045TR MADE IN MEXICO This device complies with Part 15 of the FCC Rules and RSS-210 Rules. Operation is subject to the following two conditions;...
Page 272 3-4. Using the hands-free phone system (for cellular phone) NOTICE ■ To prevent damage to a cellular phone Do not leave a cellular phone in the vehicle. The temperature inside may become high resulting in damage to the phone.
Page 273: Using The Hands-Free Phone System (For Cellular Phone)
3-4. Using the hands-free phone system (for cellular phone) ∗ Using the hands-free phone system (for cellular phone) ■ Audio unit Display A message, name, phone number, etc. is displayed. Lower-case characters and special characters, such as an umlaut, cannot be dis- played.
Page 274 3-4. Using the hands-free phone system (for cellular phone) ■ Steering wheel telephone switches Volume The voice guidance volume cannot be adjusted using this button. Off-hook switch Turns the hands-free sys- tem on/starts a call On-hook switch Turns the hands-free sys- tem off/ends a call/refuses a call Talk switch...
Page 275 3-4. Using the hands-free phone system (for cellular phone) ■ Microphone Vehicles with moon roof Vehicles without moon roof...
Page 276 3-4. Using the hands-free phone system (for cellular phone) Operating the system using a voice command By following voice guidance instructions output from the speaker, voice commands enable the operation of the hands-free phone sys- tem without the need to check the display or operate ■...
Page 277 3-4. Using the hands-free phone system (for cellular phone) Using the hands-free phone system for the first time Before using the hands-free phone system, it is necessary to register a cellular phone in the system. The phone registration mode will be entered automatically when starting the system with no cellular phone registered.
Page 278 3-4. Using the hands-free phone system (for cellular phone) Registration to the hands-free phone system only Select “Phone Only” using a voice command or STEP ® Registration to the hands-free phone system and Bluetooth audio system at the same time Select “Int.
Page 279 3-4. Using the hands-free phone system (for cellular phone) Menu list of the hands-free phone system ■ Normal operation Second First menu Third menu Operation detail menu CallBack Dialing a number stored in (Call the incoming call history back) memory Dialing a number stored in Redial the outgoing call history...
Page 280 3-4. Using the hands-free phone system (for cellular phone) Second First menu Third menu Operation detail menu Set PIN Setting a PIN code Phonebook Lock (Phone book Locking the phone book Security lock) Phonebook Unlock (Phone Unlocking the phone book book unlock) Registering the cellular Pair Phone...
Page 281 3-4. Using the hands-free phone system (for cellular phone) ■ Using a short cut key First menu Second menu Operation detail Dialing a number registered Dial “XXX (name)” in the phone book Dial “XXX (number)” Dialing the input numbers Phone book add Adding a new number entry Changing the name of a...
Page 282 3-4. Using the hands-free phone system (for cellular phone) ■ Automatic adjustment of volume When vehicle speed reaches 50 mph (80 km/h) or more, the volume auto- matically increases. The volume returns to the previous volume setting when vehicle speed drops to 43 mph (70 km/h) or less. ■...
Page 283: Making A Phone Call
3-4. Using the hands-free phone system (for cellular phone) Making a phone call ■ Making a phone call ● Dialing by inputting a number “Dial by number” ● Dialing by inputting a name “Dial by Name (Dial by name)” ● Speed dialing ●...
Page 284 3-4. Using the hands-free phone system (for cellular phone) Dialing by inputting a name Press the talk switch and say “Dial by name”. STEP Select a registered name to be input by either of the following STEP methods: a. Press the talk switch and say a registered name. b.
Page 285 3-4. Using the hands-free phone system (for cellular phone) Transferring a phone call A call can be transferred between the cellular phone and system while dialing, receiving a call, or during a call. Use one of the follow- ing methods: a.
Page 286 3-4. Using the hands-free phone system (for cellular phone) The following operations can be performed: Dialing: Press the off-hook switch or select “Dial” using a voice command or Storing the number in the phone book: Select “Store” using a voice command or Deleting: Select “Delete”...
Page 287: Setting A Cellular Phone
3-4. Using the hands-free phone system (for cellular phone) Setting a cellular phone Registering a cellular phone in the hands-free phone system allows the system to function. The following functions can be used for reg- istered cellular phones: ■ Functions and operation procedures To enter the menu for each function, follow the steps below using a voice command or ●...
Page 288 3-4. Using the hands-free phone system (for cellular phone) Selecting the cellular phone to be used Select “Select Phone” using a voice command or STEP Pattern A Select the cellular phone to be used by either of the following STEP methods, and select “Confirm”...
Page 289 3-4. Using the hands-free phone system (for cellular phone) Select the name of the cellular phone to be changed by either STEP of the following methods: a. Press the talk switch and say the desired phone name, and select “Confirm” using a voice command or b.
Page 290 3-4. Using the hands-free phone system (for cellular phone) Deleting a cellular phone Select “Delete Phone” using a voice command or STEP Select a cellular phone to be deleted by either of the following STEP methods and select “Confirm” using a voice command or a.
Page 291 3-4. Using the hands-free phone system (for cellular phone) Turning the hands-free phone automatic connection on/off ■ Turning off the automatic connection Select “Handsfree Power” using a voice command or STEP Select “Turn off” using a voice command or STEP ■...
Page 292: Security And System Setup
3-4. Using the hands-free phone system (for cellular phone) Security and system setup To enter the menu of each setting, follow the steps below: ■ Security setting items and operation procedure ● Setting or changing the PIN (Personal Identification Number) 1.
Page 293 3-4. Using the hands-free phone system (for cellular phone) ■ Changing the PIN Select “Set PIN” using a voice command or STEP Enter the registered PIN using a voice command or STEP Enter a new PIN using a voice command or STEP When using , input the code 1 digit at a time.
Page 294 3-4. Using the hands-free phone system (for cellular phone) Setting voice guidance volume Select “Guidance Vol” using STEP Change the voice guidance volume. STEP To decrease the volume: Turn counterclockwise. To increase the volume: Turn clockwise. Initialization Select “Reset Settings” and then “Confirm” using STEP Select “Confirm”...
Page 295 3-4. Using the hands-free phone system (for cellular phone) ■ Initialization ● The following data in the system can be initialized: • Phone book • Outgoing and incoming call history • Speed dials • Registered cellular phone data • Security code ●...
Page 296: Using The Phone Book
3-4. Using the hands-free phone system (for cellular phone) Using the phone book To enter the menu of each setting, follow the steps below: ● Adding a new phone number 1. “Phonebook” → 2. “Add Entry” ● Setting speed dial 1.
Page 297 3-4. Using the hands-free phone system (for cellular phone) ■ Adding procedure Select “Add Entry” using a voice command or STEP Use one of the following methods to input a telephone num- STEP ber: Inputting a telephone number using a voice command STEP2-1 Select “By Voice (By voice)”...
Page 298 3-4. Using the hands-free phone system (for cellular phone) Inputting a phone number using STEP2-1 Select “Manual Input” using STEP2-2 Input a phone number using , and press once again. Input the phone number 1 digit at a time. Selecting a phone number from outgoing or incoming call history STEP2-1 Select “Call History”...
Page 299 3-4. Using the hands-free phone system (for cellular phone) Select the name to be registered by either of the following STEP methods, and select “Confirm” using a voice command or a. Press the talk switch and say the desired name. b.
Page 300 3-4. Using the hands-free phone system (for cellular phone) Select the desired preset button, and register the data into STEP speed dial by either of the following methods: a. Press the desired preset button, and select “Confirm” using a voice command or b.
Page 301 3-4. Using the hands-free phone system (for cellular phone) Deleting registered data Select “Delete Entry” using a voice command or STEP Select the data to be deleted by either of the following meth- STEP ods, and select “Confirm” using a voice command or a.
Page 302 3-4. Using the hands-free phone system (for cellular phone) Listing the registered data Selecting “List names” using a voice command causes a list of the registered data to be read aloud. When listing is complete, the system returns to “Phonebook”. Pressing the talk switch while the desired data is being read aloud selects the data, and the following function will be available.
Page 303: Using The Interior Lights
3-5. Using the interior lights Interior lights list Personal/interior lights or personal lights (→P. 284, 285) Interior lights (→P. 283)
Page 304: Interior Light
“DOOR” position, the lights will go off automatically after 20 minutes. ■ Customization that can be configured at Toyota dealer Settings (e.g. The time elapsed before lights turn off) can be changed. (Customizable features →P. 472) Interior light “DOOR”...
Page 305: Personal/Interior Lights
3-5. Using the interior lights Personal/interior lights Personal/interior lights (vehicles with moon roof) ■ Interior lights “DOOR” position ■ Personal lights On/off...
Page 306 3-5. Using the interior lights Personal lights Personal lights (vehicles without moon roof) On/off...
Page 307: Using The Storage Features
3-6. Using the storage features List of storage features Auxiliary boxes Glove box Bottle holders Cup holders Console box CAUTION ■ Items that should not be left in the storage spaces Do not leave glasses, lighters or spray cans in the storage spaces, as this may cause the following when cabin temperature becomes high: ●...
Page 308: Glove Box
3-6. Using the storage features Glove box and console box Glove box Pull up the lever. CAUTION ■ Caution while driving Keep the glove box closed. Injuries may result in the event of an accident or sudden braking. Console box Lift the lid while pulling the lever.
Page 309: Cup Holders
3-6. Using the storage features Cup holders Cup holders Front Rear Pull the lid to open. ■ Using the cup holder (front) to store small items Remove the holders.
Page 310 3-6. Using the storage features Cup holders ■ Adjusting the cup holder to the size of the cups or drink-cans Remove the holder and change the holder position. Small size Middle size Large size CAUTION ■ Items unsuitable for the cup holder Do not place anything other than cups or aluminum cans in the cup holders.
Page 311: Bottle Holders
3-6. Using the storage features Bottle holders Bottle holders Front Rear CAUTION ■ Items unsuitable for the bottle holder Do not place anything other than pet bottles in the bottle holders. Other items may be thrown out of the holders in the event of an accident or sudden braking and cause injury.
Page 312: Auxiliary Boxes
3-6. Using the storage features Bottle holders and auxiliary boxes NOTICE ■ When a pet bottle is in the front bottle holder (vehicles with manual window) As there is a possibility of interfering with a manual window regulator handle, pre- vent the window from opening and clos- ing, do not place a pet bottle in the holder when turning the handle.
Page 313 3-6. Using the storage features Auxiliary boxes CAUTION ■ Caution while driving Keep the auxiliary boxes closed. Injuries may result in the event of an accident or sudden braking. ■ Items unsuitable for storing (overhead console only) Do not store items heavier than 0.4 lb. (0.2 kg). Doing so may cause the auxiliary box to open and the items inside may fall out, resulting in an accident.
Page 314: Other Interior Features
3-7. Other interior features Sun visors Forward position: Flip down. Side position: Flip down, unhook, and swing to the side.
Page 315: Vanity Mirrors
3-7. Other interior features Vanity mirrors Slide the cover.
Page 316: Clock
3-7. Other interior features Clock Adjusts the hour. Adjusts the minutes. Rounds nearest hour.* *: e.g. 1:00 to 1:29 → 1:00 1:30 to 1:59 → 2:00 ■ The clock is displayed when The engine switch is in the “ACC” or “ON” position.
Page 317: Ashtrays
3-7. Other interior features ∗ Ashtrays An ashtray can be installed in a cup holder. CAUTION ■ When not in use Keep the ashtray closed. Injuries may result in the event of sudden braking, sudden swerving or an accident. ■ To prevent fire ●...
Page 318: Cigarette Lighter
3-7. Other interior features ∗ Cigarette lighter Push cigarette lighter down. The cigarette lighter will pop up when it is ready for use. ■ The cigarette lighter can be used when The engine switch is in the “ACC” or “ON” position. CAUTION ■...
Page 319: Power Outlet
3-7. Other interior features ∗ Power outlet The power outlet can be used for a following component. 12 V: Accessories that run on less than 10 A. 115 V: Accessories that uses less than 100 W. Type A (12 V) Type B (115 V) ■...
Page 320 3-7. Other interior features NOTICE ■ To avoid damaging the power outlet Close the power outlet lid when the power outlet is not in use. Foreign objects or liquids that enter the power outlet may cause a short cir- cuit. ■...
Page 321: Grocery Bag Hook
3-7. Other interior features Grocery bag hook This hook is designed to hang things like grocery bag. Cabin Press the hook. Luggage compartment...
Page 322 3-7. Other interior features NOTICE ■ Grocery bag hook weight capacity Cabin Do not hang any object heavier than 44 lb. (20 kg) on the grocery bag hook. Luggage compartment Do not hang any object heavier than 7 lb. (3 kg) on the grocery bag hooks.
Page 323: Seatback Table
3-7. Other interior features ∗ Seatback table Front passenger's seatback can be used as a temporary table only when the vehicle is stopped. Fold down the front passen- ger's seat to use the seatback table. (→P. 38) CAUTION ■ Caution while driving Observe the following precautions to avoid death or serious injury.
Page 324: Floor Mat
When installing the driver's floor mat ● Do not use floor mats designed for other models or different model year vehicles, even if they are Toyota Genuine floor mats. ● Only use floor mats designed for the driver's seat. ●...
Page 325: Luggage Compartment Feature
3-7. Other interior features Luggage compartment feature ■ Cargo hooks Cargo hooks are provided for securing loose items. ■ Tie-down belts To tighten To loosen To hook To unhook...
Page 326 3-7. Other interior features ■ Auxiliary boxes Turn knobs “UNLOCK” position, remove the deck boards.
Page 327 3-7. Other interior features ■ Grocery bag hooks (→P. 300) ■ Tonneau cover (if equipped) Remove the deck board. STEP Take out the bag. STEP Remove the tonneau cover STEP from the bag.
Page 328 3-7. Other interior features Slowly unfold the tonneau STEP cover. Attach the hook to the hook STEP brackets. Raise the rear center head STEP restraint to attach the hook.
Page 329 3-7. Other interior features Folding the tonneau cover Hold the tonneau cover with both STEP hands. Point your thumbs in opposite directions. Bend one side of the cover STEP towards you. Twist the other side in the oppo- STEP site direction, as shown in the illustration.
Page 330 3-7. Other interior features Make a small circle, then fold it STEP inward. Make sure the three circles are STEP side by side. Put it in the bag. STEP...
Page 331 3-7. Other interior features CAUTION ■ When unfolding the tonneau cover Be careful not to hit yourself when unfolding the tonneau cover. ■ Caution while driving Keep the deck boards locked. Injuries may result in the event of an accident or sudden braking.
Page 332: Compass
3-7. Other interior features ∗ Compass The compass on the inside rear view mirror indicates the direction in which the vehicle is heading. ■ Operation To turn the compass on or off, press and hold “AUTO” for 3 seconds. ■ Displays and directions Display Direction...
Page 333 3-7. Other interior features Calibrating the compass The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies according to the geographic position of the vehicle. If you cross over a map boundary shown in the illustration, the compass will deviate.
Page 334 3-7. Other interior features ■ Circling calibration Stop the vehicle in a place where it is safe to drive in a circle. STEP Press and hold “AUTO” for 9 STEP seconds. C appears on the compass dis- play. Drive the vehicle at 5 mph (8 STEP km/h) or less in a circle until a direction is displayed.
Page 335 3-7. Other interior features CAUTION ■ While driving the vehicle Do not adjust the display. Be sure to adjust the display only when the vehicle is stopped. ■ When doing the circling calibration Be sure to secure a wide space, and watch out for people and vehicles in the neighborhood.
Page 336: Maintenance And Care
4-1. Maintenance and care Cleaning and protecting the vehicle exterior Perform the following to protect the vehicle and maintain it in prime condition. ● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust.
Page 337 4-1. Maintenance and care ■ Aluminum wheels ● Remove any dirt immediately by using a neutral detergent. Do not use hard brushes or abrasive cleaners. Do not use strong or harsh chemical cleaners. Use the same mild detergent and wax as used on the paint. ●...
Page 338 ■ If the windshield washer nozzle become blocked Contact your Toyota dealer. Do not try to clear it with a pin or other object. This may damage the nozzle. ■ Cleaning the exterior lights ●...
Page 339: Maintenance And Care
4-1. Maintenance and care Cleaning and protecting the vehicle interior The following procedures will help protect your vehicle's interior and keep it in top condition: ■ Protecting the vehicle interior Remove dirt and dust using a vacuum cleaner. Wipe dirty sur- faces with a cloth dampened with lukewarm water.
Page 340 4-1. Maintenance and care ■ Caring for leather areas Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle's interior. ■ Shampooing the carpets There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam.
Page 341 4-1. Maintenance and care NOTICE ■ Cleaning detergents ● Do not use organic substances such as benzene or gasoline, acidic or alkaline solutions, dye, bleach or other detergent. Doing so may discolor the vehicle interior or cause streaks or damage to painted surfaces. ●...
Page 342: Maintenance
You can perform some maintenance procedures yourself. Please be aware that do-it-yourself maintenance may affect war- ranty coverage. The use of Toyota Repair Manuals is recommended. For details about warranty coverage, see the separate “Owner’s War- ranty Information Booklet” or “Owner’s Manual Supplement”.
Page 343 It is recommended that genuine Toyota parts be used for repair to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than a Toyota dealer performs repairs, confirm the war- ranty coverage.
Page 344: Maintenance
4-2. Maintenance CAUTION ■ Warning in handling of battery ● Engine exhaust, some of its constituents, and a wide variety of automobile components contain or emit chemicals known to the State of California to cause cancer and birth defects and other reproductive harm. Work in a well ventilated area.
Page 345: General Maintenance
Booklet” “Owner’s Manual Supplement/Scheduled Maintenance Guide”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice. Engine compartment Items Check points Check the connections. Battery (→P.
Page 346: Vehicle Interior
4-2. Maintenance Vehicle interior Items Check points • Moves smoothly (without uneven Accelerator pedal pedal effort or catching)? • Can the vehicle be held securely Automatic transmission “Park” on an incline with the shift lever in mechanism • Moves smoothly? •...
Page 347: Vehicle Exterior
4-2. Maintenance Vehicle exterior Items Check points Doors • Operate smoothly? Engine hood • The lock system works properly? • Is there any leakage after park- Fluid leaks ing? • Inflation pressure is correct? • Tire surfaces not worn or dam- aged? Tires •...
Page 348: Emission Inspection And Maintenance (I/M) Programs
If the malfunction indicator lamp comes on The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/ M test and may need to be repaired. Contact your Toyota dealer to service the vehicle. ■...
Page 349: Do-It-Yourself Maintenance
Brake fluid level (→P. 345) • Rag or paper towel • Funnel (used only for adding brake fluid) • “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non-silicate, non- amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology.
Page 350 4-3. Do-it-yourself maintenance Items Parts and tools • Fuse with same amperage rating Fuses (→P. 371) as original Radiator and condenser ⎯ (→P. 344) • Tire pressure gauge Tire inflation pressure (→P. 360) • Compressed air source • Water washer fluid containing Washer fluid (→P.
Page 351 4-3. Do-it-yourself maintenance CAUTION The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury observe the following precautions. ■ When working on the engine compartment ● Keep hands, clothing, and tools away from the moving fan and engine drive belt.
Page 352 4-3. Do-it-yourself maintenance NOTICE ■ If you remove the air cleaner Driving with the air cleaner removed may cause excessive engine wear due to dirt in the air. Also, a backfire could cause a fire in the engine compart- ment.
Page 353: Hood
4-3. Do-it-yourself maintenance Hood Release the lock from the inside of the vehicle to open the hood. Pull the hood release lever. STEP The hood will pop up slightly. Lift the auxiliary catch lever STEP and lift the hood. Hold the hood open by insert- STEP ing the supporting rod into the slot.
Page 354 4-3. Do-it-yourself maintenance CAUTION ■ Pre-driving check Check that the hood is fully closed and locked. If the hood is not locked properly, it may open while the vehicle is in motion and cause an accident, which may result in death or serious injury. ■...
Page 355: Positioning A Floor Jack
4-3. Do-it-yourself maintenance Positioning a floor jack When raising your vehicle with a floor jack, position the jack cor- rectly. Improper placement may damage your vehicle or cause injury. ■ Front 1.8 L 4-cylinder (2ZR-FE) engine 2.4 L 4-cylinder (2AZ-FE) engine...
Page 356 4-3. Do-it-yourself maintenance ■ Rear 2WD models without 18-inch tires 2WD models with 18-inch tires AWD models...
Page 357 4-3. Do-it-yourself maintenance CAUTION ■ When raising your vehicle Make sure to observe the following to reduce the possibility of death or seri- ous injury. ● Lift up the vehicle using a floor jack such as the one shown in the illustra- tion.
Page 358: Engine Compartment
4-3. Do-it-yourself maintenance Engine compartment 1.8 L 4-cylinder (2ZR-FE) engine Engine oil filler cap Battery (→P. 347) (→P. 340) Radiator (→P. 344) Engine oil level dipstick Electric cooling fan (→P. 339) Condenser (→P. 344) Brake fluid reservoir Engine coolant reservoir (→P.
Page 359 4-3. Do-it-yourself maintenance 2.4 L 4-cylinder (2AZ-FE) engine Engine coolant reservoir Fuse box (→P. 371) (→P. 343) Battery (→P. 347) Engine oil filler cap Radiator (→P. 344) (→P. 340) Electric cooling fans Engine oil level dipstick Condenser (→P. 344) (→P. 339) Washer fluid tank (→P.
Page 360 4-3. Do-it-yourself maintenance Engine oil With the engine at operating temperature and turned off, check the oil level on the dipstick. ■ Checking the engine oil Park the vehicle on level ground. After turning off the engine, STEP wait more than five minutes for the oil to drain back into the bottom of the engine.
Page 361 4-3. Do-it-yourself maintenance 2.4 L 4-cylinder (2AZ-FE) engine Full ■ Adding engine oil If the oil level is below or near the low level mark, add engine oil of the same type as already in the engine. Make sure to check the oil type and prepare the items needed before adding oil.
Page 362 Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal.
Page 363 4-3. Do-it-yourself maintenance NOTICE ■ To prevent serious engine damage Check the oil level on a regular basis. ■ When replacing the engine oil ● Be careful not to spill engine oil on the vehicle components. ● Avoid overfilling, as the engine could be damaged. ●...
Page 364: Engine Coolant
If the coolant level drops within a short time after replenishing Visually check the radiator, hoses, coolant reservoir cap, radiator cap, drain cock and water pump. If you cannot find a leak, have your Toyota dealer test the cap and check for leaks in the cooling system. ■...
Page 365 Radiator and condenser Check the radiator and condenser and remove any foreign objects. If any of the above parts are extremely dirty or you are not sure of their condition, have your vehicle checked by your Toyota dealer. CAUTION ■...
Page 366 4-3. Do-it-yourself maintenance Brake fluid ■ Checking fluid level The brake fluid level should be between the “MAX” and “MIN” lines on the tank. Make sure to check the fluid type and prepare the necessary items. ■ Adding fluid Make sure to check the fluid type and prepare the necessary items. Fluid type FMVSS No.116 DOT 3 or SAE J1703 brake fluid Items...
Page 367 4-3. Do-it-yourself maintenance Disconnect claws STEP remove the service cover. Remove the reservoir cap. STEP Add brake fluid slowly while checking the fluid level. STEP ■ Brake fluid can absorb moisture from the air Excess moisture in the fluid can cause a dangerous loss of braking effi- ciency.
Page 368 4-3. Do-it-yourself maintenance NOTICE ■ If the fluid level is low or high It is normal for the brake fluid level to go down slightly as the brake pads wear or when the fluid level in the accumulator is high. If the reservoir needs frequent refilling, it may indicate a serious problem.
Page 369 4-3. Do-it-yourself maintenance CAUTION ■ Chemicals in the battery A battery contains poisonous and corrosive sulfuric acid and may produce hydrogen gas which is flammable and explosive. To reduce the risk of death or serious injury, take the following precautions while working on or near the battery: ●...
Page 370 4-3. Do-it-yourself maintenance NOTICE ■ When recharging the battery Never recharge the battery while the engine is running. Also, be sure all accessories are turned off. Washer fluid For vehicles sold in U.S.A. If any washer does not work, the washer tank may be empty. Open the lid.
Page 371 4-3. Do-it-yourself maintenance CAUTION ■ When refilling the washer fluid Do not refill the washer fluid when the engine is hot or running, as the washer fluid contains alcohol and may catch fire if spilled on the engine etc. NOTICE ■...
Page 372: Tires
■ The tire pressure warning system (if equipped) Your Toyota is equipped with a tire pressure warning system that uses tire pressure warning valves and transmitters to detect low tire inflation pressure before serious problems arise. (→P. 404) The compact spare tire is not equipped with the tire pressure...
Page 373 ID codes must be registered in the tire pressure warning computer and the tire pressure warning system must be initialized. Have tire pressure warning valve and transmitter ID codes registered by your Toyota dealer . (→P. 354) Initializing the tire pressure warning system ■...
Page 374 4-3. Do-it-yourself maintenance ■ How to initialize the tire pressure warning system Park the vehicle in a safe place and turn the engine switch STEP OFF. While the vehicle is moving, initialization is not performed. Adjust the tire inflation pressure to the specified cold tire infla- STEP tion pressure level.
Page 375 ● A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage If you are not sure, consult with your Toyota dealer. ■ Replacing tires and wheels If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly.
Page 376 Initialization can be completed in a few minutes. However, in the follow- ing cases, the settings have not been recorded and the system will not operate properly. If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer. ●...
Page 377 4-3. Do-it-yourself maintenance ■ Tire types 1 Summer tires Summer tires are high-speed performance tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow-covered or icy roads.
Page 378 4-3. Do-it-yourself maintenance ■ Tire pressure warning system certification FCC ID: PAXPMV107J FCC ID: HYQ13BCX For vehicles sold in the U.S.A. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 379 Do not mix tires of different makes, models or tread patterns. Also, do not mix tires of remarkably different treadwear. ● Do not use tire sizes other than those recommended by Toyota. ● Do not mix differently constructed tires (radial, bias-belted or bias-ply tires).
Page 380 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire.
Page 381: Tire Inflation Pressure
4-3. Do-it-yourself maintenance Tire inflation pressure ■ Tire inflation pressure The recommended cold tire inflation pressure and tire size is dis- played on the tire and loading information label. (→P. 454)
Page 382 4-3. Do-it-yourself maintenance ■ Inspection and adjustment procedure Tire valve Tire pressure gauge Remove the tire valve cap. STEP Press the tip of the tire pressure gauge onto the tire valve. STEP Read the pressure using the graduations of the gauge. STEP If the tire inflation pressure is not at the recommended level STEP...
Page 383 Reduced driving comfort and tire life ● Reduced safety ● Damage to the drive train If a tire needs frequent refilling, have it checked by your Toyota dealer. ■ Instructions for checking tire inflation pressure When checking tire inflation pressure, observe the following: ●...
Page 384 4-3. Do-it-yourself maintenance CAUTION ■ Proper inflation is critical to save tire performance Keep your tires properly inflated. Otherwise, the following conditions may occur and result in an accident causing death or serious injury. ● Excessive wear ● Uneven wear ●...
Page 385: Wheels
● Bent wheels that have been straightened ■ Aluminum wheel precautions ● Use only Toyota wheel nuts and wrenches designed for use with your aluminum wheels. ● When rotating, repairing or changing your tires, check that the wheel nuts are still tight after driving 1000 miles (1600 km).
Page 386 4-3. Do-it-yourself maintenance ■ When replacing wheels The wheels of your Toyota, except for the compact spare tire, are equipped with tire pressure warning valves and transmitters that allow the tire pressure warning system to provide advanced warning in the event of a loss in tire inflation pressure.
Page 387: Air Conditioning Filter
4-3. Do-it-yourself maintenance Air conditioning filter The air conditioning filter must be changed regularly to maintain air conditioning efficiency. ■ Removal method Turn the engine switch OFF. STEP Open the glove box. Slide off STEP the damper. Push in each side of the glove STEP box to disconnect the claws.
Page 388 4-3. Do-it-yourself maintenance ■ Replacement method Remove the air conditioning filter and replace it with a new one. The “↑UP” marks shown on the filter should be pointing up. ■ Checking interval Replace the air conditioning filter according to the maintenance schedule. In dusty areas or areas with heavy traffic flow, early replacement may be required.
Page 389: Key Battery
4-3. Do-it-yourself maintenance Key battery (vehicles with wireless remote control) Replace the battery with a new one if it is discharged. ■ You will need the following items: ● Flathead screwdriver (To prevent damage to the key, cover the tip of the screwdriver with a rag.) ●...
Page 390 The wireless remote control will not function properly. ● The operational range is reduced. ■ Use CR2025 lithium battery ● Batteries can be purchased at your Toyota dealer, jewelers, or camera stores. ● Replace only with the same or equivalent type recommended by your Toyota dealer. ●...
Page 391 4-3. Do-it-yourself maintenance NOTICE ■ For normal operation after replacing the battery Observe the following precautions to prevent accidents. ● Always work with dry hands. Moisture may cause the battery to rust. ● Do not touch or move any other components inside the remote control. ●...
Page 392: Checking And Replacing Fuses
4-3. Do-it-yourself maintenance Checking and replacing fuses If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. Turn the engine switch OFF. STEP Open the fuse box cover. STEP Engine compartment Push the tab in and lift the lid...
Page 393 4-3. Do-it-yourself maintenance Take out the pullout tool. STEP Only type A fuse can be removed using the pullout tool. For type A and B fuses: Remove the fuse. STEP Check if the fuse has blown. STEP Type A Normal fuse Blown fuse Replace it with one of an appropriate amperage rating.
Page 394 4-3. Do-it-yourself maintenance Type C Normal fuse Blown fuse Contact your Toyota dealer. Type D Normal fuse Blown fuse Contact your Toyota dealer.
Page 395 4-3. Do-it-yourself maintenance Fuse layout and amperage ratings ■ Engine compartment Fuse Ampere Circuit CDS FAN 30 A Electric cooling fan(s) RDI FAN 40 A Electric cooling fan(s) Anti-lock brake system, vehicle sta- ABS NO. 3 30 A bility control system Anti-lock brake system, vehicle sta- ABS NO.
Page 396 4-3. Do-it-yourself maintenance Fuse Ampere Circuit 60 A Electric power steering 50 A EFI MAIN, HORN, IG2 H-LP LH LO, H-LP RH LO, H-LP H-LP MAIN 50 A LH HI, H-LP RH HI EFI NO. 2 10 A Emission control system Multiport fuel injection system/ EFI NO.
Page 397 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Interior lights, personal light, clock, DOME 10 A wireless remote control SPARE 10 A Spare fuse SPARE 30 A Spare fuse SPARE 20 A Spare fuse 30 A No circuit MAYDAY 10 A No circuit Multiport fuel injection system/ EFI MAIN 20 A...
Page 398 4-3. Do-it-yourself maintenance ■ Under the driver’s side instrument panel Fuse Ampere Circuit Parking lights, tail lights, license plate lights, multiport fuel injection TAIL 10 A system/sequential multiport fuel injection system, instrument cluster lights PANEL 7.5 A Switch illumination FR DOOR 20 A Power windows, electric moon roof RL DOOR...
Page 399 4-3. Do-it-yourself maintenance Fuse Ampere Circuit SRS airbag system, multiport fuel injection system/sequential multi- 7.5 A port fuel injection system, front passenger occupant classification system METER 7.5 A Gauge and meters Air conditioning system, rear win- HTR-IG 10 A dow defogger, PTC heater WIPER 25 A Windshield wipers...
Page 400 Never use a fuse of a higher amperage rating than indicated, or use any other object in place of a fuse. ● Always use a genuine Toyota fuse or equivalent. Never replace a fuse with a wire, even as a temporary fix. This can cause extensive damage or even fire.
Page 401: Light Bulbs
You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer.
Page 402 4-3. Do-it-yourself maintenance ■ Rear bulb locations Rear turn signal lights Back-up lights Stop/tail and rear side marker lights License plate lights...
Page 403 4-3. Do-it-yourself maintenance Replacing light bulbs ■ Headlight low beams Turn the bulb base counterclock- STEP wise. Unplug the bulb while depress- STEP ing the lock release. ■ Headlight high beams and daytime running lights Turn the bulb base counterclock- STEP wise.
Page 404 4-3. Do-it-yourself maintenance Unplug the bulb while depress- STEP ing the lock release. ■ Front fog lights (if equipped) Remove the fender liner bolts STEP and clip. Partly remove the fender liner. STEP Turn the bulb base counterclock- STEP wise.
Page 405 4-3. Do-it-yourself maintenance Unplug the bulb while depress- STEP ing the lock release. ■ Front turn signal/parking and front side marker lights Turn the bulb base counterclock- STEP wise. Remove the light bulb. STEP...
Page 406 4-3. Do-it-yourself maintenance ■ Stop/tail and rear side marker lights, rear turn signal lights and back-up lights Open the back door. STEP Left side Remove the cover. STEP Right side (type A) Remove the cover using the flat- STEP head screwdriver. To protect the cover, place a rag between the flathead screwdriver and the cover.
Page 407 4-3. Do-it-yourself maintenance Turn the bulb base counterclock- STEP wise. Rear turn signal light Back-up light Stop/tail and rear side marker light Remove the light bulb. STEP Rear turn signal light Back-up light Stop/tail and rear side marker light...
Page 408 Remove the light bulb. STEP ■ LED high mounted stoplight The high mounted stoplight consists of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced.
Page 409 4-3. Do-it-yourself maintenance ■ Condensation build-up on the inside of the lens Contact your Toyota dealer for more information in the following situations. Temporary condensation build-up on the inside of the headlight lens does not indicate a malfunction. ● Large drops of water are built up on the inside of the lens.
Page 410: Essential Information
5-1. Essential information Emergency flashers Use the emergency flashers if the vehicle malfunctions or is involved in an accident. Press the switch to flash all the turn signal lights. To turn them off, press the switch once again. NOTICE ■ To prevent battery discharge Do not leave the emergency flashers on longer than necessary when the engine is not running.
Page 411: If Your Vehicle Needs To Be Towed
If your vehicle needs to be towed If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or a commercial towing service, using a lift-type truck or a flat bed truck. Use a safety chain system for all towing, and abide by all state/pro- vincial and local laws.
Page 412 5-1. Essential information Emergency towing If a tow truck is not available, in an emergency your vehicle may be temporarily towed using a cable or chain secured to the emergency towing eyelet. This should only be attempted on hard surfaced roads for short distances at low speeds.
Page 413 5-1. Essential information Towing with a sling-type truck Do not tow with a sling-type truck to prevent body damage. Towing with a wheel-lift type truck From the front (2WD models) Release the parking brake. From the front (AWD models) Use a towing dolly under the rear wheels.
Page 414 5-1. Essential information From the rear Automatic transmission: Use a towing dolly under the front wheels. Manual transmission: We recom- mend to use a towing dolly under the front wheels. When not using a towing dolly, turn the engine switch to the “ACC”...
Page 415 5-1. Essential information CAUTION ■ Caution while towing ● Use extreme caution when towing the vehicle. Avoid sudden starts or erratic driving maneuvers which place excessive stress on the emergency towing eyelet and the cables or chains. Always be cautious of the surroundings and other vehicles while towing. ●...
Page 416 5-1. Essential information NOTICE ■ To prevent body damage when towing with a sling-type truck Do not tow with a sling-type truck, either from the front or rear. ■ To prevent causing serious damage to the transmission and Active Torque Control 4WD system (AWD models) when towing using a wheel-lift type truck (vehicles with an automatic transmission) 2WD models: Never tow this vehicle from the rear with the front wheels on the...
Page 417: If You Think Something Is Wrong
5-1. Essential information If you think something is wrong If you notice any of the following symptoms, your vehicle probably needs adjustment or repair. Contact your Toyota dealer as soon as possible. ■ Visible symptoms ● Fluid leaks under the vehicle (Water dripping from the air conditioning after use is normal.)
Page 418: Fuel Pump Shut Off System
Inspect the ground under the vehicle. If you find that fuel has leaked on to the ground, the fuel system has been damaged and is in need of repair. Do not restart the engine. Have the vehi- cle checked and repaired by your Toyota dealer.
Page 419: Event Data Recorder
5-1. Essential information Event data recorder Your vehicle has computers that monitor and control certain aspects of your vehicle. These computers assist in driving and maintaining optimal vehicle performance. Besides storing data useful for troubleshooting, there is an event data recorder (EDR) that records data in a crash or a near car crash event.
Page 420 5-1. Essential information Disclosure of the data Toyota will not disclose the data recorded in an EDR to a third party except when: ● An agreement from the vehicle's owner (or the leasing company for a leased vehicle) is obtained ●...
Page 421: Steps To Take In An Emergency
Stop the vehicle immediately. Continuing to drive the vehicle may be dangerous. The following warning indicates a possible problem in the brake sys- tem. Immediately stop the vehicle in a safe place and contact your Toyota dealer. Warning light Warning light/Details Brake system warning light (warning buzzer)* •...
Page 422 Have the vehicle inspected immediately. Failing to investigate the cause of the following warnings may lead to the system operating abnormally and possibly cause an accident. Have the vehicle inspected by your Toyota dealer immediately. Warning light Warning light/Details Malfunction indicator lamp Indicates a malfunction in: (U.S.A.)
Page 423 If it is, tighten it securely. The malfunction indicator lamp will go off after taking several driving trips. If the malfunction indicator lamp does not go off even after several trips, con- tact your Toyota dealer as soon as possible.
Page 424 5-2. Steps to take in an emergency CAUTION ■ When the electric power steering warning light comes on The steering wheel may become extremely heavy. If the steering wheel becomes heavier than usual when operating, firmly hold and operate it using more force than usual. Follow the correction procedures.
Page 425 1 minute: Have the system checked Malfunction in the tire by your Toyota dealer. pressure warning system. :Open door warning buzzer: A buzzer will sound if the vehicle reaches a speed of 3 mph (5 km/h) with any door open.
Page 426 5-2. Steps to take in an emergency buzzer sounds intermittently for 10 seconds after the vehicle has reached a speed of 12 mph (20 km/h). Then, if the seat belt is still unfastened, the buzzer will sound at a different tone for 20 more seconds. :Maintenance required reminder light: Refer to the seperate “Scheduled Maintenace Guide”...
Page 427 If there is a lot of snow or ice on the vehicle, in particular around the wheels or wheel housings. ● If non-genuine Toyota wheels are used. (Even if you use Toyota wheels, the tire pressure warning system may not work properly with some types of tires.) ●...
Page 428 Customization that can be configured at Toyota dealer The vehicle speed linked seat belt reminder buzzer can be disabled. (Customizable features →P. 472) However, Toyota recommends that the seat belt reminder buzzer be operational to alert the driver and front passen- ger that the seat belts are not fastened.
Page 429 5-2. Steps to take in an emergency CAUTION ■ Maintenance of the tires Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label (tire and load information label).
Page 430 5-2. Steps to take in an emergency CAUTION Your vehicle has also been equipped with a TPMS (tire pressure warning system) malfunction indicator to indicate when the system is not operat- ing properly. The TPMS (tire pressure warning system) malfunction indi- cator is combined with the low tire pressure telltale (tire pressure warning light).
Page 431: If You Have A Flat Tire
5-2. Steps to take in an emergency If you have a flat tire Remove the flat tire and replace it with the spare provided. ■ Before jacking up the vehicle ● Stop the vehicle on a hard, flat surface. ● Set the parking brake. ●...
Page 432 5-2. Steps to take in an emergency Taking out the jack Turn the knobs to the “UNLOCK” STEP position and remove the deck board. Detach the hook. STEP...
Page 433 5-2. Steps to take in an emergency Taking out the spare tire Turn the knobs to the “UNLOCK” STEP position and remove the deck boards. Loosen the center fastener that STEP secures the spare tire.
Page 434 5-2. Steps to take in an emergency Replacing a flat tire Chock the tires. STEP Wheel Flat tire chock posi- tions Behind the Left- rear right- hand hand side side tire Front Behind the Right- rear left- hand hand side side tire In front of...
Page 435 5-2. Steps to take in an emergency Slightly loosen the wheel nuts STEP (one turn). Turn the tire jack portion “A” by STEP hand until the notch of the jack is in contact with the jack point. The jack point guides are located under the rocker panel.
Page 436 5-2. Steps to take in an emergency Raise the vehicle until the tire is STEP slightly raised off the ground. Remove all the wheel nuts and STEP the tire. When resting the tire on the ground, place the tire so that the wheel design faces up to avoid scratching the wheel surface.
Page 437 5-2. Steps to take in an emergency Installing the tire Remove any dirt or foreign mat- STEP ter from the wheel contact sur- face. If foreign matter is on the wheel contact surface, the wheel nuts may loosen while the vehicle is in motion, and the tire may come off the vehicle.
Page 438 5-2. Steps to take in an emergency Lower the vehicle. STEP Firmly tighten each nut two or STEP three times in the order shown in the illustration. Tightening torque: 76 ft•lbf (103 N•m, 10.5 kgf•m) Stow the flat tire, tire jack and all tools. STEP Stowing the flat tire Vehicles with aluminum wheel:...
Page 439 5-2. Steps to take in an emergency Put the flat tire on the deck STEP boards with the outer side of the wheel facing up. Hook the belt clips closest to the buckles onto the front cargo hooks. Pass the belts through the center STEP hole of the wheel.
Page 440 5-2. Steps to take in an emergency Pull the ends of the belts to STEP secure the tire. ■ The compact spare tire ● The compact spare tire is identified by the label “TEMPORARY USE ONLY” on the tire sidewall. Use the compact spare tire temporarily only in an emergency.
Page 441 5-2. Steps to take in an emergency CAUTION ■ Using the tire jack Improper use of the tire jack may lead to death or serious injuries due to the vehicle suddenly falling off the jack. ● Do not use the tire jack for any purpose other than replacing tires or installing and removing tire chains.
Page 442 5-2. Steps to take in an emergency CAUTION ■ Replacing a flat tire Observe the following precautions to reduce the risk of death or serious injury: ● Never use oil or grease on the wheel bolts or wheel nuts. Oil and grease may cause the wheel nuts to be excessively tightened, leading to bolt or disc wheel damage.
Page 443 5-2. Steps to take in an emergency CAUTION ■ When the spare tire is attached The vehicle speed may not be correctly detected, and the following sys- tems may not operate correctly: ● ABS & Brake assist ● ● TRAC Also, not only can the following system not be utilized fully, it may actu- ally negatively effect the drive-train components: ●...
Page 444 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and...
Page 445: If The Engine Will Not Start
One of the following may be the cause of the problem. ● One or both of the battery terminals may be disconnected. ● The battery may be discharged. (→P. 428) Contact your Toyota dealer if the problem cannot be repaired, or if repair procedures are unknown.
Page 446: If The Shift Lever Cannot Be Shifted From P
(a system to prevent accidental operation of the shift lever). Have the vehicle inspected by your Toyota dealer. The following steps may be used as an emergency measure to ensure that the shift lever can be shifted.
Page 447: If You Lose Your Keys
5-2. Steps to take in an emergency If you lose your keys New genuine keys can be made by your Toyota dealer. Bring a mas- ter key and the key number stamped on the key number plate.
Page 448: If The Battery Is Discharged
You can call your Toyota dealer or qualified repair shop. If you have a set of jumper (or booster) cables and a second vehi- cle with a 12-volt battery, you can jump start your Toyota following the steps below. 1.8 L 4-cylinder (2ZR-FE) engine Remove the engine cover.
Page 449 Once the vehicle’s engine has started, remove the jumper STEP cables in the exact reverse order in which they were con- nected. Once the engine starts, have the vehicle checked at your Toyota dealer as soon as possible.
Page 450 Once the vehicle’s engine has started, remove the jumper STEP cables in the exact reverse order in which they were con- nected. Once the engine starts, have the vehicle checked at your Toyota dealer as soon as possible.
Page 451 5-2. Steps to take in an emergency ■ Avoiding a discharged battery ● Turn off the headlights and the audio system while the engine is turned off. ● Turn off any unnecessary electrical components when the vehicle is run- ning at a low speed for an extended period, such as in heavy traffic, etc. CAUTION ■...
Page 452 5-2. Steps to take in an emergency NOTICE ■ To prevent damage to the vehicle Do not pull- or push-start the vehicle, because the catalytic converter may overheat and become a fire hazard. ■ When handling jumper cables Be careful that the jumper cables do not become tangled in the cooling fans or any of the belts when connecting or disconnecting them.
Page 453: If Your Vehicle Overheats
Wait until the temperature of the engine (shown on the instrument cluster) begins to fall and then stop the engine. If the fans are not operating: Stop the engine and call your Toyota dealer. After the engine has cooled STEP STEP...
Page 454 Water can be used in an emer- gency if engine coolant is (→ unavailable. P. 449 Have the vehicle checked at the nearest Toyota dealer as soon as possible. ■ Overheating If you observe the following, your vehicle may be overheating.
Page 455 5-2. Steps to take in an emergency NOTICE ■ When adding engine coolant Wait until the engine has cooled down before adding engine coolant. When adding coolant, do so slowly. Adding cool coolant to a hot engine too quickly can cause damage to the engine.
Page 456: If The Vehicle Becomes Stuck
5-2. Steps to take in an emergency If the vehicle becomes stuck Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt, or snow. Stop the engine. Set the parking brake and put the shift STEP lever in P (automatic transmission) or N (manual transmis- sion).
Page 457 5-2. Steps to take in an emergency NOTICE ■ To avoid damaging the transmission and other components ● Avoid spinning the wheels and do not rev the engine. ● If the vehicle remains stuck after trying these procedures, the vehicle may require towing to be freed.
Page 458: If Your Vehicle Has To Be Stopped In An Emergency
5-2. Steps to take in an emergency If your vehicle has to be stopped in an emergency Only in an emergency, such as if it becomes impossible to stop the vehicle in the normal way, stop the vehicle using the following pro- cedure: Steadily step on the brake pedal with both feet and firmly STEP...
Page 459 5-2. Steps to take in an emergency CAUTION ■ If the engine has to be turned off while driving ● Power assist for the brakes and steering wheel will be lost, making the brake pedal harder to depress and the steering wheel heavier to turn. Decelerate as much as possible before turning off the engine.
Page 460 5-2. Steps to take in an emergency...
Page 461: Specifications Maintenance Data (Fuel, Oil Level, Etc.)
6-1. Specifications Maintenance data (fuel, oil level, etc.) Dimensions and weights 171.9 in. (4365 mm) Overall length 173.0 in. (4395 mm) Overall width 69.5 in. (1765 mm) 61.0 in. (1550 mm) Overall height 61.4 in. (1560 mm) Wheelbase 102.4 in. (2600 mm) Front 59.8 in.
Page 462 Vehicle identification number The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle. This number is stamped on the top left of the instrument panel.
Page 463 6-1. Specifications ■ Engine number The engine number is stamped on the engine block as shown. 1.8 L 4-cylinder (2ZR-FE) engine 2.4 L 4-cylinder (2AZ-FE) engine...
Page 464 6-1. Specifications Engine 1.8 L 4-cylinder (2ZR-FE) engine Model 2ZR-FE engine 4 cylinder in line, Type 4 cycle, gasoline 3.17 × 3.48 in. Bore and stroke (80.5 × 88.3 mm) Displacement 109.7 cu.in. (1798 cm Drive belt tension 143 ± 22 lbf (650 ± 100 N, 65 ± 10 kgf) Valve clearance (engine cold) Intake Automatic adjustment...
Page 465 6-1. Specifications 2.4 L 4-cylinder (2AZ-FE) engine Model 2AZ-FE engine 4 cylinder in line, Type 4 cycle, gasoline 3.48 × 3.78 in. Bore and stroke (88.5 × 96.0 mm) Displacement 144.1 cu.in. (2362 cm Drive belt tension Automatic adjustment Valve clearance (engine cold) 0.007 ⎯...
Page 466: Lubrication System
3.8 qt. (3.6 L, 3.2 Imp. qt.) ■ Engine oil selection “Toyota Genuine Motor Oil” is used in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the following grade and viscosity. Oil grade: ILSAC multigrade engine oil Recommended viscosity: 1.8 L 4-cylinder (2ZR-FE) engine...
Page 467 6-1. Specifications The 20 in 0W-20 indicates the oil viscosity when the oil is at its operating temperature. An oil with a higher viscosity may be better suited if the vehi- cle is operated at high speeds, or under extreme load conditions. 2.4 L 4-cylinder (2AZ-FE) engine SAE 5W-20 or 0W-20 SAE 5W-20 or 0W-20 engine oil...
Page 468: Cooling System
(Reference) 2.4 L 4-cylinder (2AZ-FE) engine 6.0 qt. (5.7 L, 5.0 Imp. qt.) Use either of the following. • “Toyota Super Long Life Coolant” • Similar high-quality ethylene glycol-based non-silicate, Coolant type non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology Do not use plain water alone.
Page 469: Electrical System
Recommended API grade GL-4 Recommended gear oil SAE 75W viscosity NOTICE ■ Manual transaxle gear oil Using manual transmission gear oil other than “TOYOTA Genuine Manual Transmission Gear Oil LV” may cause occurrence of idle rattling noise and bad fuel consumption.
Page 470: Automatic Transaxle
Toyota Genuine ATF WS NOTICE ■ Automatic transmission fluid type Using automatic transmission fluid other than “Toyota Genuine ATF WS” may cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimately damage the transmission of your vehicle.
Page 471 6-1. Specifications Rear differential (AWD models) Oil capacity 0.5 qt. (0.5 L, 0.4 Imp. qt.) Oil type Hypoid gear oil API GL-5 Above 0°F (-18°C): SAE 90 Recommended oil viscosity Below 0°F (-18°C): SAE 80W or 80W-90 Transfer (AWD models) Oil capacity 0.8 qt.
Page 472 6-1. Specifications Brakes 1.8 L 4-cylinder (2ZR-FE) engine 3.4 in. (87 mm) 2.4 L 4-cylinder (2AZ-FE) engine • AWD models: 3.4 in. (87 mm) Pedal clearance • 2WD models with P215/45R18 tires: 3.4 in. (87 mm) • 2WD models with tires other than the above: 3.3 in.
Page 473 6-1. Specifications Steering Free play Less than 1.2 in. (30 mm) Tires and wheels 16-inch tires P205/55R16 89H, T135/80R16 101M or Tire size T135/70R17 102M 2WD models Front: 32 psi (220 kPa, 2.2 kgf/cm bar) Rear: 32 psi (220 kPa, 2.2 kgf/cm bar) Spare: 60 psi (420 kPa, 4.2 kgf/cm Tire inflation pressure...
Page 474 6-1. Specifications 17-inch tires P215/45R17 87W, T135/80R16 101M or Tire size T135/70R17 102M 2WD models Front: 32 psi (220 kPa, 2.2 kgf/cm bar) Rear: 32 psi (220 kPa, 2.2 kgf/cm bar) Spare: 60 psi (420 kPa, 4.2 kgf/cm Tire inflation pressure bar) (Recommended cold tire AWD models...
Page 475 6-1. Specifications Light bulbs Light Bulbs Bulb No. Type Headlights Low beam 9006 High beam 9005 Front turn signal/park- ing and front side 3457NA 27/7 marker lights Front fog lights (if ⎯ Exterior equipped) ⎯ Rear turn signal lights Stop/tail and rear side 7443 21/5 marker lights...
Page 476: Fuel Information
ASTM D4814 in the U.S.A. and CGSB3.5-M93 in Canada. ■ Fuel tank opening for unleaded gasoline To help prevent incorrect fueling, your Toyota has a fuel tank opening that only accommodates the special nozzle on unleaded fuel pumps. ■...
Page 477 Toyota allows the use of oxygenate blended gasoline where the oxygen- ate content is up to 10% ethanol or 15% MTBE. ● If you use gasohol in your Toyota, be sure that it has an octane rating no lower than 87. ●...
Page 478 6-1. Specifications NOTICE ■ Notice on fuel quality ● Do not use improper fuels. If improper fuels are used the engine will be damaged. ● Do not use leaded gasoline. Leaded gasoline can cause damage to your vehicle’s catalytic converters causing the emission control system to malfunction.
Page 479: Tire Information
6-1. Specifications Tire information Typical tire symbols Full-size tire Compact spare tire Tire size (→P. 463) DOT and Tire Identification Number (TIN) (→P. 462) Uniform tire quality grading For details, see “Uniform Tire Quality Grading” that follows. Location of treadwear indicators (→P.
Page 480 6-1. Specifications Tire ply composition and materials Plies are layers of rubber-coated parallel cords. Cords are the strands which form the plies in a tire. Radial tires or bias-ply tires A radial tire has “RADIAL” on the sidewall. A tire not marked “RADIAL”...
Page 481 6-1. Specifications Typical DOT and Tire Identification Number (TIN) DOT symbol Tire Identification Number (TIN) Tire manufacturer's identifica- tion mark Tire size code Manufacturer's optional tire type code (3 or 4 letters) Manufacturing week Manufacturing year : The DOT symbol certifies that the tire conforms to applicable Federal...
Page 482 6-1. Specifications Tire size ■ Typical tire size information The illustration indicates typical tire size. Tire use (P = Passenger car, T = Temporary use) Section width (millimeters) Aspect ratio (tire height to section width) Tire construction code (R = Radial, D = Diagonal) Wheel diameter (inches) Load index (2 or 3 digits) Speed symbol...
Page 483 U.S. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading. Your Toyota dealer will help answer any questions you may have as you read this information. ■ DOT quality grades All passenger vehicle tires must conform to Federal Safety Requirements in addition to these grades.
Page 484 6-1. Specifications ■ Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speci- fied government test course. For example, a tire graded 150 would wear one and a half (1-1/2) times as well on the government course as a tire graded 100.
Page 485 6-1. Specifications Warning: The temperature grades for this tire are established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either sepa- rately or in combination, can cause heat buildup and possible tire fail- ure.
Page 486 6-1. Specifications Tire related term Meaning 150 lb. (68 kg) times the number of occupants Normal occupant specified in the second column of Table 1 that weight follows Distribution of occupants in a vehicle as speci- Occupant distribution fied in the third column of Table 1 below The combined weight of installed regular pro- duction options weighing over 5 lb.
Page 487 6-1. Specifications Tire related term Meaning The surface area of the rim not covered by the Weather side inflated tire The part of the tire that is made of steel wires, Bead wrapped or reinforced by ply cords and that is shaped to fit the rim A breakdown of the bond between components Bead separation...
Page 488 6-1. Specifications Tire related term Meaning The parting of the innerliner from cord material Innerliner separation in the carcass (a) The sidewall that contains a whitewall, bears white lettering, or bears manufac- turer, brand, and/or model name molding that is higher or deeper than the same Intended outboard molding on the other sidewall of the tire, or sidewall...
Page 489 6-1. Specifications Tire related term Meaning A layer of rubber-coated parallel cords A parting of rubber compound between adja- Ply separation cent plies A mechanical device made of rubber, chemi- cals, fabric and steel or other materials, that, Pneumatic tire when mounted on an automotive wheel, pro- vides the traction and contains the gas or fluid that sustains the load...
Page 490 6-1. Specifications Tire related term Meaning That portion of a tire that comes into contact Tread with the road A tread section running circumferentially Tread rib around a tire Tread separation Pulling away of the tread from the tire carcass The projections within the principal grooves Treadwear indicators designed to give a visual indication of the...
Page 491: Customization
Your vehicle includes a variety of electronic features that can be per- sonalized to your preferences. Programming these preferences requires specialized equipment and may be performed by your Toyota dealer. Some function settings are changed simultaneously with other functions being customized. Contact your Toyota dealer. Customized Item Function Default setting...
Page 492 6-2. Customization Customized Item Function Default setting setting Driver's door unlocked in one All doors Unlocking using a key step, all doors unlocked in one unlocked in two step steps Opening driver's door Door lock unlocks all doors (vehicles with power Shifting gears to P door lock unlocks all doors.
Page 493: Initialization Items To Initialize
6-3. Initialization Items to initialize The following items must be initialized for normal system operation in cases such as after maintenance is performed on the vehicle. Item When to initialize Reference Maintenance data After the maintenance is performed P. 323 •...
Page 494: Reporting Safety Defects For U.s. Owners
If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800-331-4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 495: Seat Belt Instructions For Canadian Owners (In French)
Seat belt instructions for Canadian owners (in French) The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions in English. Utilisation correcte des ceintures de sécurité...
Page 496 Entretien et soin ■ Ceintures de sécurité Nettoyez avec un chiffon ou une éponge humectée d'eau savonneuse tiède. Profitez l'occasion pour vérifier régulièrement que les ceintures ne sont pas effilochées, entaillées, ou ne paraissent pas exagérément usées. ATTENTION ■ Détérioration et usure des ceintures de sécurité Inspectez les ceintures de sécurité...
Page 497: Srs Airbag Instructions For Canadian Owners (In French)
SRS airbag instructions for Canadian owners (in French) The following is a French explanation of SRS airbag instructions extracted from the SRS airbag section in this manual. See the SRS airbag section for more detailed SRS airbag instructions in English. Sacs de sécurité...
Page 498 Composition du système de sacs de sécurité gonflables Capteurs sacs Témoin d'alerte SRS sécurité gonflables frontaux Contacteur de boucle de Système de classification ceinture sécurité l'occupant siège passager avant passager avant (ECU et Boîtier électronique de sacs capteurs) de sécurité gonflables Capteurs sacs Capteurs...
Page 499 Votre véhicule est équipé de SACS DE SÉCURITÉ GONFLABLES INTELLIGENTS (ADVANCED AIRBAGS) conçus selon les normes de sécurité américaines applicables aux véhicules à moteur (FMVSS208). Le système de sacs de sécurité gonflables régule la puissance de déploiement des sacs de sécurité gonflables conducteur et passager avant.
Page 500 ATTENTION ■ Précautions avec les sacs de sécurité gonflables SRS Respectez les précautions suivantes avec les sacs de sécurité gonflables. À défaut, des blessures graves, voire mortelles, pourraient s'ensuivre. ● Le conducteur et tous les passagers à bord du véhicule doivent porter leur ceinture de sécurité...
Page 501 être grièvement blessés ou tués par le déploiement d'un sac de sécurité gonflable. Installez dans un siège de sécurité enfant les enfants trop jeunes pour pouvoir utiliser la ceinture de sécurité. Toyota recommande vivement que les nourrissons et les jeunes enfants soient installés sur le siège arrière du véhicule et convenablement attachés.
Page 502 ATTENTION ■ Précautions avec les sacs de sécurité gonflables SRS ● Ne pas s'asseoir sur le bord du siège et ne pas s'appuyer contre la planche de bord. ● Ne laissez pas un enfant rester debout devant le sac de sécurité gonflable SRS passager avant ou bien s'asseoir sur les genoux du passager avant.
Page 503 ATTENTION ■ Précautions avec les sacs de sécurité gonflables SRS ●Ne fixez ni ne posez aucun objet sur la planche de bord ou la garniture centrale du volant de direction. Au déploiement des sacs de sécurité gonflables SRS conducteur et passager avant, tout objet...
Page 504 ■ Modification et mise au rebut des éléments du système de sacs de sécurité gonflables SRS Consultez impérativement votre concessionnaire Toyota si vous avez besoin d'intervenir sur votre véhicule ou de procéder à l'une des modifications suivantes. Les sacs de sécurité gonflables SRS risquent de ne pas fonctionner correctement ou de se déployer (gonfler) accidentellement, provoquant ainsi...
Page 505: Alphabetical Index
Alphabetical index Alphabetical index A/C ..........172 Antenna........186 ABS........... 145 Anti-lock brake system....145 Active Torque Control 4WD Ashtray........296 system ........145 Audio input .......225 Air conditioning filter....366 Audio system Air conditioning system Antenna.........186 Air conditioning filter ..... 366 Audio input ......225 Air conditioning AUX port........225 system........
Page 506 Alphabetical index Back door Child restraint system Back door ........34 Booster seats, definition..88 Wireless remote control ..26 Booster seats, installation ..92 Back-up lights Convertible seats, Wattage.........456 definition .......88 Battery Convertible seats, Checking .......347 installation......92 If the vehicle has a Front passenger occupant discharged battery ....428 classification system.....83 Preparing and checking...
Page 507 Alphabetical index Child-protectors ......30 Driving Cleaning Break-in tips ......106 Exterior ......... 316 Correct posture .......69 Interior ........319 Procedures......104 Seat belts ......320 Winter driving tips....154 Clock ........295 Compass ........311 Electric power steering ...145 Condenser ....... 344 Emergency flashers Console box......
Page 508 Alphabetical index Engine Floor mat ........303 Compartment ......337 Fluid Engine switch ......115 Brake........345 Hood........332 Washer........349 How to start the Fog lights engine .........115 Replacing light bulbs..... 380 Identification number.....443 Switch ........137 If the engine will not start ..425 Wattage.........
Page 509 Alphabetical index Fuel door........62 I/M test........327 Fuel filler door ......62 Identification number Fuel pump shut off system ..398 Engine ........443 Fuses........371 Vehicle ........443 Ignition switch......115 Illuminated entry system..283 Gas station information..500 Indicator lights ......132 Gauges ........129 Initialization Glove box.........
Page 510 Alphabetical index License plate lights Mirrors Replacing light bulbs .....380 Inside rear view mirror ....53 Switch........135 Side mirror heater ....179 Wattage.........456 Side mirrors......55 Light bulbs Vanity mirrors......294 Replacing ......380 Moon roof ........59 Wattage.........456 MP3 disc ........197 Lights Emergency flasher switch ..390 Noise from under vehicle..18 Fog light switch .....137...
Page 511 Alphabetical index Radiator........344 Emergency Locking Radio ........183 Retractor .......47 Rear seats How to wear your seat belt..46 Folding down ......42 How your child should wear Rear side marker lights the seat belt ......48 Replacing light bulb ....380 Pregnant women, proper seat Switch........
Page 512 Alphabetical index Side marker lights Tachometer ......129 Replacing light bulbs .....380 Tail lights Switch........135 Replacing light bulbs..... 380 Wattage.........456 Switch ........135 Side mirror Wattage......... 456 Adjusting .........55 Talk switch ....... 253 Spare tire Telephone switch..... 253 Inflation pressure....360 Theft deterrent system Storage location ....411 Engine immobilizer system ..66...
Page 513 Alphabetical index TRAC ........146 Low tire pressure warning Traction control....... 146 light ........404 Trip meter......... 129 Malfunction indicator lamp ..402 Turn signal lights Open door ......404 Replacing light bulbs .... 380 Pretensioners ......402 Switch........126 Seat belt reminder light ..404 Wattage ........
Page 514: What To Do If
What to do if... What to do if... If you have a flat tire A tire punctures P. 411 P. 425 If the engine will not start The engine does not start P. 66 Engine immobilizer system P. 428 If the battery is discharged If the shift lever cannot be shifted The shift lever cannot be P.
Page 515 What to do if... ■Warning lights Brake system warning Active Torque Control 4WD sys- light tem warning light P. 402 Maintenance required reminder light P. 401 P. 404 Charging system warn- Tire pressure warning ing light light P. 402 P. 404 Low engine oil pressure Low windshield washer fluid level warning light...
Page 516: Gas Station Information
GAS STATION INFORMATION Auxiliary catch lever Fuel filler door P. 332 P. 62 Hood lock release lever Fuel filler door opener Tire inflation pressure P. 332 P. 62 P. 454 Fuel tank capacity 13.2 gal. (50 L, 10.9 Imp. gal.) (Reference) Fuel type Unleaded gasoline only...

Toyota 2011 Matrix Owner's Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Toyota 2011 Matrix

Summary of Contents for Toyota 2011 Matrix

Table of Contents