Toyota 2014 Venza Owner's Manual
Hide thumbs Also See for 2014 Venza:
Table of Contents

Advertisement

TABLE OF CONTENTS
1
Before driving
2
When driving
Interior
3
features
Maintenance
4
and care
When trouble
5
arises
Vehicle
6
specifications
7
For owners
Index
VENZA_OM_OM73019U_(U)
Adjusting and operating features such as door locks,
mirrors, and steering column
Driving, stopping and safe-driving information
Air conditioning and audio systems, as well as other in-
terior features for a comfortable driving experience
Cleaning and protecting your vehicle, performing do-it-
yourself maintenance, and maintenance information
What to do if the vehicle needs to be towed, gets a flat
tire, or is involved in an accident
Detailed vehicle information
Reporting safety defects for U.S. owners, and seat belt
and SRS airbag instructions for Canadian owners
Alphabetical listing of information contained in this
manual
1

Advertisement

Table of Contents
loading

Summary of Contents for Toyota 2014 Venza

  • Page 1 TABLE OF CONTENTS Adjusting and operating features such as door locks, Before driving mirrors, and steering column When driving Driving, stopping and safe-driving information Interior Air conditioning and audio systems, as well as other in- features terior features for a comfortable driving experience Maintenance Cleaning and protecting your vehicle, performing do-it- and care...
  • Page 2: Table Of Contents

    TABLE OF CONTENTS Index For information regarding the equipment listed below, refer to the “Navigation System Owner’s Manual” or “Display Audio System Owner’s Manual”. • Navigation system • Rear view monitor system • Audio system 1-4. Opening and closing the Before driving windows and moon roof Power windows.....
  • Page 3 2-3. Operating the lights and When driving wipers Headlight switch ....208 Automatic High Beam..212 2-1. Driving procedures Fog light switch....219 Driving the vehicle....160 Windshield wipers and Engine (ignition) switch washer......221 (vehicles with smart Rear window wiper and key system).......
  • Page 4 TABLE OF CONTENTS Index 3-4. Using the storage features Interior features List of storage features ..309 • Glove box ......310 • Console boxes....311 3-1. Using the air conditioning • Overhead console .... 313 system and defogger • Cup holders ...... 314 •...
  • Page 5 Maintenance and care When trouble arises 4-1. Maintenance and care 5-1. Essential information Cleaning and protecting Emergency flashers.... 430 the vehicle exterior.... 346 If your vehicle needs Cleaning and protecting to be towed....... 431 the vehicle interior..... 349 If you think something is wrong......
  • Page 6 TABLE OF CONTENTS Index Vehicle specifications Index 6-1. Specifications Abbreviation list ....548 Maintenance data (fuel, oil level, etc.) ... 486 Alphabetical index.... 550 Fuel information ....500 Tire information ....504 What to do if..... 559 6-2. Customization Customizable features ..
  • Page 7 VENZA_OM_OM73019U_(U)
  • Page 8 Pictorial index Exterior  Windshield wipers P. 221 Moon roof P. 100 Hood P. 363 Outside rear view mirrors P. 92 Side turn signal lights P. 183 Fog lights P. 219 Headlights P. 208 Daytime running lights P. 210 Front turn signal lights P.
  • Page 9 Rear window defogger P. 296 Tail lights P. 208 Fuel filler door P. 104 Rear window wiper P. 225 Side doors P. 50 Back door License plate Tires P. 56 light P. 208 ●Rotation P. 382 ●Replacement P. 453 Rear view monitor system * ●Inflation pressure P.
  • Page 10 Pictorial index Interior Head restraints P. 78 Seat belts P. 81 SRS driver airbag P. 118 Power window switches P. 96 SRS front passenger airbag P. 118 Floor mats Rear seats P. 70 P. 328 Glove box P. 310 Console boxes P.
  • Page 11 Assist grips P. 327 Personal/interior lights P. 306, 307 Personal/interior lights SRS curtain shield airbags P. 306, 307 P. 118 Vanity mirrors P. 321 Garage door opener switches P. 332  Moon roof switches P. 100 Overhead console P. 313 Sun visors P.
  • Page 12 Pictorial index Interior  Driving position memory switches P. 73 Inside lock button P. 51 Door lock switch P. 51 Power window switches P. 96 Window lock switch P. 96 VENZA_OM_OM73019U_(U)
  • Page 13  Shift lever P. 178 Seat heater switches P. 324 Shift lock override button P. 467 Auxiliary box P. 317 Console box Cup holders P. 311 P. 314 AUX port/USB port Auxiliary box P. 317 P. 304 Power outlet P. 322 ...
  • Page 14: Instrument Panel

    Pictorial index Instrument panel Headlight switch P. 208 Windshield wipers and washer switch P. 221 Turn signal lever Rear window wiper and washer switch P. 183 P. 225 Fog light switch P. 219 Engine (ignition) switch (vehicles with smart key system) P.
  • Page 15 VSC OFF switch P. 240 Intuitive parking assist switch P. 231  Power back door switch P. 57 Outside rear view mirror switches P. 93 Auxiliary box P. 317  Power back door main switch P. 59  : If equipped : Refer to “Navigation System Owner’s Manual”...
  • Page 16 Pictorial index Instrument panel Telephone switch * Audio remote control switches Talk switch Cruise control switch P. 227 Engine (ignition) switch (vehicles without smart key system) P. 175 Emergency flasher Multi-information display switches switch P. 430 P. 192, 204 VENZA_OM_OM73019U_(U)
  • Page 17 Air conditioning system P. 286 Rear window defogger switch P. 296  : If equipped : Refer to “Navigation System Owner’s Manual” or “Display Audio System Owner’s Manual”. VENZA_OM_OM73019U_(U)
  • Page 18 Pictorial index Luggage compartment  Power back door switch P. 58 Back door handle P. 57 Luggage cover P. 330 Luggage compartment light P. 307 Shopping bag Shopping bag hook P. 330 hook P. 330 Rear seat lever P. 71 Auxiliary box P.
  • Page 19 Power outlet P. 322 Rear seat lever P. 71  : If equipped VENZA_OM_OM73019U_(U)
  • Page 20: For Your Information

    Accessories, spare parts and modification of your Toyota A wide variety of non-genuine spare parts and accessories for Toyota vehi- cles are currently available in the market. You should know that Toyota does not warrant these products and is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.
  • Page 21 ● Cruise control system ● Anti-lock brake system ● SRS airbag system ● Seat belt pretensioner system Be sure to check with your Toyota dealer for precautionary measures or spe- cial instructions regarding installation of a mobile two-way radio system. VENZA_OM_OM73019U_(U)
  • Page 22 Furthermore, these computers do not record con- versations, sounds or pictures. ● Data usage Toyota may use the data recorded in these computers to diagnose malfunc- tions, conduct research and development, and improve quality. Toyota will not disclose the recorded data to a third party except: •...
  • Page 23 Event data recorder This vehicle is equipped with an event data recorder (EDR). The main pur- pose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed.
  • Page 24 ● Disclosure of the EDR data Toyota will not disclose the data recorded in an EDR to a third party except when: • An agreement from the vehicle’s owner (or the lessee for a leased vehicle) is obtained • In response to an official request by the police, a court of law or a govern- ment agency •...
  • Page 25 CAUTION ■ General precautions while driving Driving under the influence: Never drive your vehicle when under the influ- ence of alcohol or drugs that have impaired your ability to operate your vehi- cle. Alcohol and certain drugs delay reaction time, impair judgment and reduce coordination, which could lead to an accident that could result in death or serious injury.
  • Page 26 This is a warning against anything which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your Toyota and its equipment.
  • Page 27: Before Driving

    Before driving 1-1. Key information 1-4. Opening and closing the windows and moon roof Keys ........28 Power windows ....96 1-2. Opening, closing and locking Moon roof......100 the doors Sunshade......103 Smart key system ....30 1-5. Refueling Wireless remote control ......
  • Page 28: 1-1. Key Information

    1-1. Key information Keys The following keys are provided with the vehicle. Vehicles with smart key system Electronic keys • Operating the smart key system (P. 30) • Operating wireless remote control function (P. 45) Mechanical keys Key number plate Vehicles without smart key system Keys Operating the wireless remote...
  • Page 29 Keep the plate in a safe place such as your wallet, not in the vehicle. In the event that a key is lost, a new key can be made at your Toyota dealer using the key number plate. (P. 468) ■...
  • Page 30: 1-2. Opening, Closing And Locking The Doors

    1-2. Opening, closing and locking the doors  Smart key system The following operations can be performed simply by carrying the electronic key on your person, for example in your pocket. (The driver should always carry the electronic key.) Locks and unlocks the doors (P. 31) Locks and unlocks the doors (P.
  • Page 31 1-2. Opening, closing and locking the doors Unlocking and locking the doors Front door handle Grip the driver’s door handle to unlock the door. Grip the passen- ger’s door handle to unlock all the doors. Make sure to touch the sensor on the back of the handle.
  • Page 32 1-2. Opening, closing and locking the doors Back door Press the unlock button to unlock the door. The door cannot be unlocked for 3 seconds after the door is locked. Lock the back door again when you leave the vehicle. The back door will not lock automatically after it has been opened and then closed.
  • Page 33 1-2. Opening, closing and locking the doors Antenna location and effective range ■ Antenna location Antennas outside cabin Antennas inside cabin Antenna outside luggage com- partment VENZA_OM_OM73019U_(U)
  • Page 34 1-2. Opening, closing and locking the doors ■ Effective range (areas within which the electronic key is detected) When locking or unlock- ing the doors The system can be oper- ated when the electronic key is within about 2.3 ft. (0.7 m) of an outside door handle.
  • Page 35 1-2. Opening, closing and locking the doors ■ Operation signals A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: Once; Unlocked: Twice) ■ When the door cannot be locked using the topside sensor area If the door will not lock even when the topside sensor area is touched, try touch- ing both the topside and underside sen-...
  • Page 36 1-2. Opening, closing and locking the doors ■ Switching the door unlock function It is possible to set which doors the entry function unlocks. STEP Turn the “ENGINE START STOP” switch OFF. STEP When the indicator on the key surface is turned off, press and hold for approximately 5 seconds while pressing the key.
  • Page 37 1-2. Opening, closing and locking the doors ■ Battery-saving function In the following circumstances, the entry function is disabled in order to pre- vent the vehicle and electronic key batteries from discharging. ● When the entry function has not been used for 2 weeks or more ●...
  • Page 38 1-2. Opening, closing and locking the doors ■ To operate the system properly Make sure to carry the electronic key when operating the system. Do not get the electronic key too close to the vehicle when operating the system from outside of the vehicle.
  • Page 39 1-2. Opening, closing and locking the doors ● Even if the electronic key is not inside the vehicle, it may be possible to start the engine if the electronic key is near the window. ● The doors may unlock or lock if a large amount of water splashes on the door handle, such as in the rain or in a car wash when the electronic key is within the effective range.
  • Page 40 1-2. Opening, closing and locking the doors ■ When the vehicle is not driven for extended periods To prevent theft of the vehicle, do not leave the electronic key within 6 ft. (2 m) of the vehicle. ■ Security feature If a door is not opened within approximately 60 seconds after the vehicle is unlocked, the security feature automatically locks the vehicle again.
  • Page 41 1-2. Opening, closing and locking the doors Alarm Situation Correction procedure The “ENGINE START STOP” switch was turned to ACCESSORY mode Turn the “ENGINE while the driver’s door was START STOP” switch open (or the driver’s door OFF and close the was opened while the Interior alarm driver’s door...
  • Page 42 1-2. Opening, closing and locking the doors Alarm Situation Correction procedure The electronic key has a Replace the electronic low battery key battery An attempt was made to Interior alarm start the engine without the Start the engine with pings once electronic key being the electronic key present, or the electronic...
  • Page 43 1-2. Opening, closing and locking the doors ■ If the smart key system does not operate properly ● Locking and unlocking the doors: Use the mechanical key. (P. 469) ● Starting the engine (P. 470) ■ When the electronic key battery is fully depleted P.
  • Page 44 (P. 33) The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your Toyota dealer for details, such as the frequency of radio waves and timing of emitting the radio waves.
  • Page 45: Wireless Remote Control

    1-2. Opening, closing and locking the doors Wireless remote control The wireless remote control can be used to lock and unlock the vehi- cle from outside the vehicle. Vehicles with smart key system Locks all doors Unlocks all doors Pressing the button unlocks the driver’s door.
  • Page 46 1-2. Opening, closing and locking the doors Vehicles without smart key system Locks all doors Pressing holding: Sounds alarm (P. 114) Unlocks all doors Pressing the button unlocks the driver’s door. Pressing the button again within 3 seconds unlocks the other doors. Pressing holding: Opens...
  • Page 47 1-2. Opening, closing and locking the doors ■ Door lock buzzer If a door or back door is not fully closed, a buzzer sounds continuously for 10 seconds if an attempt to lock the door is made. Fully close the door to stop the buzzer, and lock the vehicle once more.
  • Page 48 1-2. Opening, closing and locking the doors ■ Conditions affecting operation Vehicles with smart key system P. 35 Vehicles without smart key system The wireless remote control function may not operate normally in the fol- lowing situations. ●Near a TV tower, radio station, electric power plant, airport or other facility that generates strong radio waves ●When carrying a portable radio, cellular phone or other wireless com- munication device...
  • Page 49 1-2. Opening, closing and locking the doors ■ Certification for wireless remote control For vehicles sold in the U.S.A. NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Page 50: Side Doors

    1-2. Opening, closing and locking the doors Side doors The vehicle can be locked and unlocked using the entry function, wireless remote control, key or door lock switch. ■ Entry function (vehicles with smart key system) P. 30 ■ Wireless remote control P.
  • Page 51 1-2. Opening, closing and locking the doors ■ Door lock switch Locks all doors Unlocks all doors ■ Inside lock button Locks the door Unlocks the door The front doors can be opened by pulling the inside handles even if the lock buttons are in the lock position.
  • Page 52 1-2. Opening, closing and locking the doors Locking the driver’s doors from the outside without a key STEP Move the inside lock button to the lock position. STEP Close the door. Vehicles with smart key system The door cannot be locked if the “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode, or the electronic key is left inside the vehicle.
  • Page 53 1-2. Opening, closing and locking the doors Automatic door locking and unlocking systems The following functions can be set or canceled: Function Operation Shift position linked Shifting the shift lever out of “P” locks all door locking function doors. Shift position linked Shifting the shift lever to “P”...
  • Page 54 1-2. Opening, closing and locking the doors STEP Vehicles with smart key system: Close all the doors and switch the “ENGINE START STOP” switch to IGNITION ON mode. (Perform STEP within 20 sec- onds.) Vehicles without smart key system: Close all the doors and switch the engine switch to the “ON” STEP position.
  • Page 55 1-2. Opening, closing and locking the doors ■ Impact detection door lock release system In the event that the vehicle is subject to a strong impact, all the doors are unlocked. Depending on the force of the impact or the type of accident, however, the system may not operate.
  • Page 56: Back Door

    1-2. Opening, closing and locking the doors Back door The back door can be opened using the back door opener. The back door can be locked and unlocked using the entry function (vehicles with smart key system), wireless remote control or door lock switch. In addition, the power back door (if equipped) can be opened using the power back door switch or wireless remote control.
  • Page 57 1-2. Opening, closing and locking the doors ■ Opening the back door from inside the vehicle (vehicles with power back door) Push and hold the switch to open/close. Pressing switch again while the power back door is operating will cause the opera- tion to reverse.
  • Page 58 1-2. Opening, closing and locking the doors Power back door switch (vehicles with power back door) Push the switch to close. Pressing the switch again while the power back door is closing will cause it to open again. However, the reverse operation cannot be performed for the first second after pressing the switch to close the door.
  • Page 59 1-2. Opening, closing and locking the doors Canceling the power back door system (vehicles with power back door) Turn the main switch to disable the power back door system. Inoperative Operative The back door cannot be oper- ated even with the wireless remote control or power back door switch.
  • Page 60 1-2. Opening, closing and locking the doors ■ The power back door can be opened/closed when (vehicles with power back door) Vehicles with smart key system ● The “ENGINE START STOP” switch is in IGNITION ON mode, and the shift lever is in “P”. ●...
  • Page 61 1-2. Opening, closing and locking the doors CAUTION ■ While driving ● Keep the back door closed while driving. If the back door is left open, it may hit near-by objects while driving or lug- gage may be unexpectedly thrown out, causing an accident. In addition, exhaust gases may enter the vehicle, causing death or a seri- ous health hazard.
  • Page 62 1-2. Opening, closing and locking the doors CAUTION ■ Operating the back door Observe the following precautions. Failure to do so may cause parts of the body to be caught, resulting in death or serious injury. ● Remove any heavy loads, such as snow and ice, from the back door before opening it.
  • Page 63 If a bicycle carrier or similar heavy object is attached to the back door, it may suddenly shut again after being opened, causing someone’s hands, head or neck to be caught and injured. When installing an accessory part to the back door, using a genuine Toyota part is recommended. ■ Back door closer ●...
  • Page 64 When installing an accessory part to the back door, using a genuine Toyota part is recom- mended. VENZA_OM_OM73019U_(U)
  • Page 65 Do not touch the damper stay rod with gloves or other fabric items. ● Do not attach any accessories other Damper stay than genuine Toyota parts to the back door. ● Do not place your hand on the damper stay or apply lateral forces to it.
  • Page 66 1-2. Opening, closing and locking the doors NOTICE ■ To prevent back door closer malfunction Do not apply excessive force to the back door while the back door closer is operating. ■ To prevent damage to the power back door (vehicles with power back door) ●...
  • Page 67: Adjustable Components (Seats, Mirrors, Steering Wheel)

    1-3. Adjustable components (seats, mirrors, steering wheel) Front seats Power seat Seat position fore/aft control switch Seatback angle control switch Seat cushion (front) angle control switch (driver’s side only) Vertical height control switch (driver’s side only) Lumbar support control switch Manual seat Seat position fore/aft adjust- ment lever...
  • Page 68 1-3. Adjustable components (seats, mirrors, steering wheel) Active head restraints When the occupant’s lower back presses against the seatback during a rear-end collision, the head restraint moves slightly for- ward and upward to help reduce the risk of whiplash on the seat occupant.
  • Page 69 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Seat adjustment ● Be careful that the seat does not hit passengers or luggage. ● Do not recline the seat more than necessary when the vehicle is in motion to reduce the risk of sliding under the lap belt. If the seat is too reclined, during an accident the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury.
  • Page 70: Rear Seats

    1-3. Adjustable components (seats, mirrors, steering wheel) Rear seats Seatback angle adjustment lever Pull up the lever until the lock is completely released. Folding down the rear seatbacks ■ Before folding down the rear seatbacks Stow the seat belt buckles and STEP lower the head restraints to the lowest position.
  • Page 71 1-3. Adjustable components (seats, mirrors, steering wheel) Pass the outer seat belts and STEP plates through the seat belt hangers. This prevents the shoulder belt from being damaged. Make sure that the seat belts are removed from the hangers before using them.
  • Page 72 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Seat adjustment Do not recline the seat more than necessary when the vehicle is in motion, to reduce the risk of sliding under the lap belt. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of an accident.
  • Page 73: Driving Position Memory

    1-3. Adjustable components (seats, mirrors, steering wheel)  Driving position memory Your preferred driving position (the position of the driver’s seat and angle of the outside rear view mirrors) can be memorized and recalled by pressing a button. It is also possible to set this function to activate automatically when the doors are unlocked.
  • Page 74 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Recalling the memorized position STEP Check that the shift lever is in P. STEP Vehicles with smart key system: Turn the “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system: Turn the engine switch is in the “ON”...
  • Page 75 1-3. Adjustable components (seats, mirrors, steering wheel) Power easy access system The auto away/return function enables easy access by activat- ing when the driver attempts to enter or exit the vehicle. Auto away function (exiting the vehicle) When all of the following actions have been performed, the seat will move backward: ●...
  • Page 76 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Operating the driving position memory after turning the “ENGINE START STOP” switch off (vehicles with smart key system) or the key is removed from the engine switch (vehicle without smart key system) Memorized seat positions can be activated up to 180 seconds after the driver’s door is opened and another 60 seconds after it is closed again.
  • Page 77 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Seat adjustment caution Take care during seat adjustment so that the seat does not strike the rear passenger or squeeze your body against the steering wheel. VENZA_OM_OM73019U_(U)
  • Page 78: Head Restraints

    1-3. Adjustable components (seats, mirrors, steering wheel) Head restraints Head restraints are provided for all seats. Front and rear outboard seats Vertical adjustment Pull the head restraint up. Lock Down release button Push the head restraints down while pressing the lock release button.
  • Page 79 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Adjusting the height of the head restraints Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears. ■ Adjusting the rear center seat head restraint Always raise the head restraint one level from the stowed position when using.
  • Page 80 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Head restraint precautions Observe the following precautions regarding the head restraints. Failure to do so may result in death or serious injury. ● Use the head restraints designed for each respective seat. ●...
  • Page 81: Seat Belts

    1-3. Adjustable components (seats, mirrors, steering wheel) Seat belts Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. ■ Correct use of the seat belts Extend the shoulder belt so that it comes fully over the shoulder, does come into contact with the...
  • Page 82 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Adjusting the height of the belt (front seats) Down Move the height adjuster up and down as needed until you hear a click. Seat belt pretensioners (front seats) The pretensioner helps the seat belt to quickly restrain the occu- pant by retracting the seat belt when the vehicle is subjected to...
  • Page 83 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Emergency locking retractor (ELR) The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend, and you can move around fully.
  • Page 84 Each seat belt should be used by one person only. Do not use a seat belt for more than one person at the same time, including children. ● Toyota recommends that children should be seated in the rear seat and always use a seat belt and/or an appropriate child restraint system. ●...
  • Page 85 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Pregnant women Obtain medical advice and wear the seat belt in the proper way. (P. 81) Women who are pregnant should position the lap belt as low as possible over the hips in the same manner as other occu- pants.
  • Page 86 ● Do not attempt to install, remove, modify, disassemble or dispose of a seat belt. Have any necessary repairs carried out by your Toyota dealer. Inap- propriate handling of the pretensioner may cause it to activate or operate improperly and may cause death or serious injury.
  • Page 87 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Using a seat belt extender ● Do not wear the seat belt extender, if you can fasten the seat belt without the extender. ● Do not use the seat belt extender when installing a child restraint system, because the belt will not securely hold the child restraint system, increas- ing the risk of death or serious injury in the event of a sudden stop, sudden swerve or an accident.
  • Page 88: Steering Wheel

    1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel The steering wheel can be adjusted to a comfortable position. Hold the steering wheel and STEP press the lever down. Adjust to the ideal position by STEP moving the steering wheel horizontally and vertically.
  • Page 89: Inside Rear View Mirror

    1-3. Adjustable components (seats, mirrors, steering wheel) Inside rear view mirror The rear view mirror’s position can be adjusted to enable sufficient confirmation of the rear view in accordance with the driver’s seating posture. Adjusting the height of rear view mirror Adjust the height of the rear view mirror by moving it up and down.
  • Page 90 1-3. Adjustable components (seats, mirrors, steering wheel) Automatic anti-glare function Responding to the level of brightness of the headlights of vehicles behind, the reflected light is automatically reduced. Changing automatic anti-glare function mode ON/OFF When the automatic anti-glare function is in ON mode, the indi- cator illuminates.
  • Page 91 1-3. Adjustable components (seats, mirrors, steering wheel) ■ To prevent sensor error To ensure correct functioning of the sen- sors, do not touch or cover the sensors. CAUTION ■ While driving Do not adjust the position of the mirror. Doing so may lead to mishandling of the vehicle and an accident, or result- ing in death or serious injury.
  • Page 92: Outside Rear View Mirrors

    1-3. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors Mirror angle can be adjusted using the switch. Select a mirror to adjust. STEP Left Right Adjust the mirror. STEP Right Down Left Folding back the mirrors (power type) Press the switch to fold the mir- rors.
  • Page 93 1-3. Adjustable components (seats, mirrors, steering wheel) Folding back the mirrors (manual type) Push backward to fold the mir- rors. Blind Spot Mirrors The Blind Spot Mirrors increase the view of surrounding area to assist the driver when checking surrounding area before chang- ing lanes.
  • Page 94 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Mirror angle can be adjusted when Vehicles with smart key system The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ACC” or “ON” position. ■...
  • Page 95 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ While driving Observe the following precautions. Failing to do so may result in losing control of the vehicle and cause an acci- dent, resulting in death or serious injury. ● Do not adjust the mirrors. ●...
  • Page 96: Opening And Closing The Windows And Moon Roof Power Windows

    1-4. Opening and closing the windows and moon roof Power windows The power windows can be opened and closed using the following switches. One-touch closing Closing One-touch opening Opening :To stop the window partway, operate the switch in the opposite direction. Lock switch Press the switch down to lock passenger window switches.
  • Page 97 1-4. Opening and closing the windows and moon roof ■ The power windows can be operated when Vehicles with smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ON” position. ■...
  • Page 98 If you release the switch while the window is moving, start again from the beginning. If the window continues to close but then re-open slightly even after performing the above procedure correctly, have the vehicle inspected by your Toyota dealer. ■ Customization Settings (e.g.
  • Page 99 1-4. Opening and closing the windows and moon roof CAUTION ■ Closing the windows Observe the following precautions. Failing to do so may result in death or serious injury. ● Check to make sure that all passengers do not have any part of their body in a position where it could be caught when a window is being operated.
  • Page 100: Moon Roof

    1-4. Opening and closing the windows and moon roof  Moon roof Use the overhead switches to open, close, and tilt the moon roof up and down. ■ Opening and closing Open The moon roof stops slightly before the fully open position to reduce wind noise.
  • Page 101 1-4. Opening and closing the windows and moon roof ■ The moon roof can be operated when Vehicles with smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ON” position. ■...
  • Page 102 To ensure the initialization is complete, make sure opening, closing, tilting up and down functions work properly. If the moon roof does not fully close even after performing the above proce- dure correctly, have the vehicle inspected by your Toyota dealer. CAUTION ■...
  • Page 103: Sunshade

    1-4. Opening and closing the windows and moon roof  Sunshade The sunshade can be opened and closed manually. Front Slide the sunshade. The front sunshade will open automatically when the moon roof is opened. (P. 100) Rear Slide the sunshade. ...
  • Page 104: 1-5. Refueling

    1-5. Refueling Opening the fuel tank cap Perform the following steps to open the fuel tank cap. ■ Before refueling the vehicle ● Vehicles with smart key system Turn the “ENGINE START STOP” switch off and ensure that all the doors and windows are closed. ●...
  • Page 105 1-5. Refueling Hang the fuel tank cap on the STEP back of the fuel filler door. Closing the fuel tank cap When replacing the fuel tank cap, turn it until a clicking sound is heard. After releasing your hand, the cap will turn slightly to the opposite direction.
  • Page 106 1-5. Refueling CAUTION ■ Refueling the vehicle Observe the following precautions while refueling the vehicle. Failure to do so, may result in death or serious injury. ● Touch the vehicle or some other metal surface to discharge any static electricity. Sparks resulting from discharging static electricity may cause the fuel vapors to ignite.
  • Page 107 Do not top off the fuel tank ■ When replacing the fuel tank cap Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.
  • Page 108: Theft Deterrent System Engine Immobilizer System

    1-6. Theft deterrent system Engine immobilizer system The vehicle’s keys have built-in transponder chips that prevent the engine from starting if the key has not been previously registered in the vehicle’s on-board computer. Never leave the keys inside the vehicle when you leave the vehicle. Vehicles with smart key sys- tem: The indicator light flashes after...
  • Page 109 1-6. Theft deterrent system ■ System maintenance The vehicle has a maintenance-free type engine immobilizer system. ■ Conditions that may cause the system to malfunction ● If the key is in contact with a metallic object. ● If the key is in close proximity to or touching a key to the security system (key with a built-in transponder chip) of another vehicle.
  • Page 110 1-6. Theft deterrent system ● For vehicles sold in Canada Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. NOTICE ■...
  • Page 111: Alarm

    1-6. Theft deterrent system  Alarm The system sounds the alarm and flashes lights when forcible entry is detected. ■ Triggering of the alarm The alarm is triggered in the following situations when the alarm is set. ● A locked door is unlocked or opened in any way other than by using the entry function (vehicles with smart key system), the wireless remote control door lock function or the mechanical key.
  • Page 112 1-6. Theft deterrent system ■ Deactivating or stopping the alarm Do one of the following to deactivate or stop the alarm. ● Unlock the doors using the entry function (vehicles with smart key system) or the wireless remote control. ● Start the engine. (The alarm will be deactivated or stopped after a few seconds.) ■...
  • Page 113 1-6. Theft deterrent system ■ Triggering of the alarm The alarm may be triggered in the following situations. (Stopping the alarm deactivates the alarm system.) ● The doors are unlocked using the mechanical key. ● A person inside the vehicle opens a door or hood.
  • Page 114 1-6. Theft deterrent system ■ Panic mode Vehicles with smart key system When is pressed for longer than about one second, an alarm will sound for about 60 seconds and the vehicle lights will flash or come on to deter any person from trying to break into or damage your vehicle.
  • Page 115: Theft Prevention Labels (U.s.a.)

    1-6. Theft deterrent system Theft prevention labels (U.S.A.) These labels are attached to the vehicle to reduce vehicle theft by facilitating the tracing and recovery of parts from sto- len vehicles. Do not remove under penalty of law. ITY16C012 VENZA_OM_OM73019U_(U)
  • Page 116: Safety Information Correct Driving Posture

    1-7. Safety information Correct driving posture Drive with a good posture as follows: Sit upright and well back in the seat. Adjust the position of the seat forward or backward to ensure the pedals can be reached easily depressed to the extent required.
  • Page 117 1-7. Safety information CAUTION ■ While driving ● Do not adjust the position of the driver’s seat. Doing so could cause the driver to lose control of the vehicle. ● Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger.
  • Page 118: Srs Airbags

    1-7. Safety information SRS airbags The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury. Front airbags Driver airbag/front passenger airbag Can help protect the head and chest of the driver and front pas-...
  • Page 119 1-7. Safety information Side and curtain shield airbags Side airbags Can help protect the torso of the front seat occupants. Curtain shield airbags Can help protect primarily the head of front and rear outboard seat occupants. VENZA_OM_OM73019U_(U)
  • Page 120 1-7. Safety information Airbag system components Front passenger airbag Driver airbag Curtain shield airbag Side and curtain shield airbag sensor Seat belt pretensioners and force limiters Driver’s seat belt buckle switch Side airbag Driver’s seat position sensor “AIR BAG ON/OFF” indicator light Knee airbag Front passenger occupant...
  • Page 121 1-7. Safety information Your vehicle is equipped with “ADVANCED AIRBAGS” designed based on the US motor vehicle safety standards (FMVSS208). The airbag sensor assembly (ECU) controls airbag deployment based on information obtained from the sensors etc. shown in the system com- ponents diagram above.
  • Page 122: Front Passenger

    1-7. Safety information ■ SRS airbag deployment conditions (front airbags) ● The SRS front airbags will deploy in the event of an impact that exceeds the set threshold level (the level of force corresponding to an approxi- mately 12 - 18 mph [20 - 30 km/h] frontal collision with a fixed wall that does not move or deform).
  • Page 123 1-7. Safety information ■ Conditions under which the SRS airbags may deploy (inflate), other than a collision The SRS front airbags may also deploy if a serious impact occurs to the underside of your vehicle. Some examples are shown in the illustration. ●...
  • Page 124 1-7. Safety information ■ Types of collisions that may not deploy the SRS airbag (side airbags and curtain shield airbags) The SRS side airbag and curtain shield airbag system may not activate if the vehicle is subjected to a collision from the side at certain angles, or a colli- sion to the side of the vehicle body other than the passenger compartment.
  • Page 125: Front Passenger

    1-7. Safety information ■ When to contact your Toyota dealer In the following cases, the vehicle will require inspection and/or repair. Con- tact your Toyota dealer as soon as possible. ● Any of the SRS airbags have been inflated. ●...
  • Page 126 1-7. Safety information ● The surface of the seats with the side airbag is scratched, cracked, or other- wise damaged. ● The portion of the front, center and rear pillars or roof side rail garnishes (pad- ding) containing the curtain shield air- bags inside is scratched, cracked or otherwise damaged.
  • Page 127 1-7. Safety information CAUTION ■ SRS airbag precautions Observe the following precautions regarding the airbags. Failure to do so may cause death or serious injury. ● The driver and all passengers in the vehicle must wear their seat belts properly. The SRS airbags are supplemental devices to be used with the seat belts.
  • Page 128: Front Passenger

    An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are the safest for infants and children.
  • Page 129: Front Passenger

    1-7. Safety information CAUTION ■ SRS airbag precautions ● Do not sit on the edge of the seat or lean against the dashboard. ● Do not allow a child to stand in front of the SRS front passenger airbag unit or sit on the knees of a front passenger.
  • Page 130: Front Passenger

    1-7. Safety information CAUTION ■ SRS airbag precautions ● Do not attach anything to or lean any- thing against areas such as the dash- board or steering wheel pad or lower portion of the instrument panel. These items can become projectiles when SRS driver, front passenger and knee airbags deploy.
  • Page 131 Wash off any residue as soon as possible to prevent skin irritation. ● If the areas where the SRS airbags are stored, such as the steering wheel pad and front, center and rear pillar garnishes, are damaged or cracked, have them replaced by your Toyota dealer. VENZA_OM_OM73019U_(U)
  • Page 132 Modification and disposal of SRS airbag system components Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer. The SRS airbag may malfunction or deploy (inflate) accidentally, causing death or serious injury.
  • Page 133: Front Passenger Occupant Classification System

    1-7. Safety information Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the front passen- ger seat and activates or deactivates the devices for front passenger. SRS warning light Front passenger’s seat belt reminder light “AIR BAG ON”...
  • Page 134 1-7. Safety information Condition and operation in the front passenger occupant classi- fication system ■ Adult “AIR BAG ON” and “AIR BAG OFF” “AIR BAG indicator lights ON” Indicator/ warning light SRS warning light Front passenger’s seat belt reminder light Flashing Front passenger airbag Side airbag on the front passenger seat...
  • Page 135 1-7. Safety information ■ Unoccupied “AIR BAG ON” and “AIR BAG OFF” Not illumi- indicator lights nated Indicator/ warning light SRS warning light Front passenger’s seat belt reminder light Front passenger airbag Deactivated Side airbag on the front passenger seat Activated Curtain shield airbag Devices...
  • Page 136 1-7. Safety information ■ System malfunction “AIR BAG ON” and “AIR BAG OFF” “AIR BAG indicator lights OFF” Indicator/ warning light SRS warning light Front passenger’s seat belt reminder light Front passenger airbag Deactivated Side airbag on the front passenger seat Devices Curtain shield airbag Activated...
  • Page 137 1-7. Safety information CAUTION ■ Front passenger occupant classification system precautions Observe the following precautions regarding front passenger occupant clas- sification system. Failure to do so may cause death or serious injury. ● Wear the seat belt properly. ● Make sure the front passenger’s seat belt tab has not been left inserted into the buckle before someone sits in the front passenger seat.
  • Page 138 Do not kick the front passenger seat or subject it to severe impact. Other- wise, the SRS warning light may come on to indicate a malfunction in the detection system. In this case, contact your Toyota dealer immediately. ● Child restraint systems installed on the rear seat should not contact the front seatbacks.
  • Page 139: Child Restraint Systems

    1-7. Safety information Child restraint systems A child restraint system for a small child or baby must itself be prop- erly restrained on the seat with the lap portion of the lap/shoulder belt. The laws of all 50 states of the U.S.A. and Canada now require the use of child restraint systems.
  • Page 140 1-7. Safety information Types of child restraints Child restraint systems are classified into the following 3 types according to the age and size of the child. Rear facing  Infant seat/convertible seat Forward facing  Convertible seat VENZA_OM_OM73019U_(U)
  • Page 141 1-7. Safety information Booster seat ■ When installing the child restraint system on the front passenger seat When you have to use a child restraint system on the front passenger seat, adjust the following: ● The seatback to the most upright posi- tion ●...
  • Page 142 ● Toyota strongly urges the use of a proper child restraint system that con- forms to the size of the child, installed on the rear seat. According to acci- dent statistics, the child is safer when properly restrained in the rear seat than in the front seat.
  • Page 143 1-7. Safety information CAUTION ■ Child restraint precautions ● Do not use the seat belt extender when installing a child restraint system on the front or rear passenger seat. If installing a child restraint system with the seat belt extender connected to the seat belt, the seat belt will not securely hold the child restraint system, which could cause death or seri- ous injury to the child or other passengers in the event of a sudden stop, sudden swerve or an accident.
  • Page 144 1-7. Safety information CAUTION ■ When the child restraint system is not in use ● Keep the child restraint system properly secured on the seat even if it is not in use. Do not store the restraint unsecured in the passenger compart- ment.
  • Page 145: Installing Child Restraints

    1-7. Safety information Installing child restraints Follow the child restraint system manufacturer’s instructions. Firmly secure child restraints to the rear seats using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder belt can be used if your child restraint system is not compatible with the LATCH (Lower Anchors and Tethers for Chil- dren) system.
  • Page 146 1-7. Safety information Anchor bracket (for top tether strap) Anchor brackets are provided for all rear seats. Installation with LATCH system Fold the seatback while pulling STEP the lever. Return the seatback and secure it as upright as possi- ble (1st lock position). Adjust the seatback to the 3rd lock position.
  • Page 147 1-7. Safety information Type A STEP Widen the gap between the seat cushion and seatback slightly. STEP Latch the hooks of the lower straps onto the LATCH anchors. The bars are installed in the clearance between the seat cushion and seatback. STEP If the child restraint has a top tether strap, the top...
  • Page 148 1-7. Safety information Type B STEP Widen the gap between the seat cushion and seatback slightly. STEP Latch the buckles onto the LATCH anchors. The bars are installed in the clearance between the seat cushion and seatback. STEP If the child restraint has a top tether strap, the top tether strap should be latched...
  • Page 149 1-7. Safety information Installing child restraints using a seat belt (child restraint lock function belt) Rear-facing  Infant seat/convertible seat ■ Place the child restraint system STEP on the rear seat facing the rear of the vehicle. Run the seat belt through the STEP child restraint system and insert the plate into the buckle.
  • Page 150 1-7. Safety information Fully extend the shoulder belt STEP and then allow it to retract slightly in order to activate the ALR lock mode. Lock mode allows the seat belt to retract only. While pushing the child restraint STEP system down into the rear seat, allow the shoulder belt to retract until the child restraint system is securely in place.
  • Page 151 1-7. Safety information Forward-facing Convertible seat ■ Place the child restraint system STEP on the seat facing the front of the vehicle. Run the seat belt through the STEP child restraint system and insert the plate into the buckle. Make sure that the belt is not twisted.
  • Page 152 1-7. Safety information Fully extend the shoulder strap STEP and then allow it to retract slightly into the ALR lock mode. Lock mode allows the seat belt to retract only. While pushing the child restraint STEP system into the rear seat, allow the shoulder belt to retract until the child restraint system is securely in place.
  • Page 153 1-7. Safety information ■ Booster seat Place the booster seat on the STEP seat facing the front of the vehi- cle. Sit the child in the booster seat. STEP Fit the seat belt to the booster seat according to the manufac- turer’s instructions and insert the plate into the buckle.
  • Page 154 1-7. Safety information Removing a child restraint installed with a seat belt Press the buckle release button and fully retract the seat belt. Child restraint systems with a top tether strap STEP Secure the child restraint using a seat belt or lower anchors, and do the following.
  • Page 155 1-7. Safety information Open the anchor bracket cover, STEP latch the hook onto the anchor bracket and tighten the top tether strap. Make sure the top tether strap is securely latched. Outside only: Adjust the head STEP restraint to the downmost posi- tion.
  • Page 156 1-7. Safety information CAUTION ■ When installing a child restraint system Follow the directions given in the child restraint system installation manual and fix the child restraint system securely in place. If the child restraint system is not correctly fixed in place, the child or other passengers may be seriously injured or even killed in the event of sudden braking, sudden swerving or an accident.
  • Page 157 1-7. Safety information CAUTION ■ When installing a child restraint system ● When installing a child restraint system in the rear center seat, adjust both seatbacks at the same angle. Otherwise, the child restraint system cannot be securely restrained and this may cause death or serious injuries in the event of sudden braking, sudden swerving or an accident.
  • Page 158 1-7. Safety information CAUTION ■ Do not use a seat belt extender If a seat belt extender is used when installing a child restraint system, the seat belt will not securely hold the child restraint system, which could cause death or serious injury to the child or other passengers in the event of sud- den braking, sudden swerving or an accident.
  • Page 159: When Driving

    When driving 2-1. Driving procedures 2-3. Operating the lights and wipers Driving the vehicle.... 160 Headlight switch....208 Engine (ignition) switch (vehicles with smart Automatic High Beam ..212 key system)....171 Fog light switch ....219 Engine (ignition) switch Windshield wipers and (vehicles without smart washer ......
  • Page 160: 2-1. Driving Procedures

    2-1. Driving procedures Driving the vehicle The following procedures should be observed to ensure safe driv- ing. ■ Starting the engine P. 171, 175 ■ Driving STEP With the brake pedal depressed, shift the shift lever to “D”. (P. 178) STEP Release the parking brake.
  • Page 161 2-1. Driving procedures STEP Vehicles with smart key system: Turn the “ENGINE START STOP” switch off and stop the engine. Vehicles without smart key system: Turn the engine switch to the “LOCK” position and stop the engine. STEP Lock the door, making sure that you have the key on your person.
  • Page 162 Your vehicle has a drum-in-disc type parking brake system. This type of brake system needs bedding-down of the brake shoes periodi- cally or whenever the parking brake shoes and/or drums are replaced. Have your Toyota dealer perform the bedding-down. ■ Operating your vehicle in a foreign country Comply with the relevant vehicle registration laws and confirm the availability of the correct fuel.
  • Page 163 Large amounts of exhaust in the vehi- cle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the vehicle inspected by your Toyota dealer immediately. VENZA_OM_OM73019U_(U)
  • Page 164 2-1. Driving procedures CAUTION ● Do not shift the shift lever to “P” while the vehicle is moving. Doing so can damage the transmission and may result in a loss of vehicle control. ● Do not shift the shift lever to “R” while the vehicle is moving forward. Doing so can damage the transmission and may result in a loss of vehicle control.
  • Page 165 2-1. Driving procedures CAUTION ● Do not adjust the position of the steering wheel, the seat, or the inside or outside rear view mirrors while driving. Doing so may result in a loss of vehicle control that can cause accidents that may result in death or serious injury.
  • Page 166 2-1. Driving procedures CAUTION ■ When the vehicle is stopped ● Do not race the engine. If the vehicle is in any gear other than “P” or “N”, the vehicle may acceler- ate suddenly and unexpectedly, and may cause an accident. ●...
  • Page 167 The exhaust should be checked occasionally. If there is a hole or crack caused by corrosion, damage to a joint or abnormal exhaust noise, be sure to have the vehicle inspected and repaired by your Toyota dealer. Failure to do so may allow exhaust gases to enter the vehicle, resulting in death or a serious health hazard.
  • Page 168 2-1. Driving procedures CAUTION ■ When braking the vehicle ● When the brakes are wet, drive more cautiously. Braking distance increases when the brakes are wet, and may cause one side of the vehicle to brake differently than the other side. Also the parking brake may not securely hold the vehicle.
  • Page 169 If you hear a squealing or scraping noise (brake pad wear limit indica- tors) Have your Toyota dealer check and replace the brake pads as soon as pos- sible. The rotor damage can result if the pads are not replaced when needed.
  • Page 170 Short in electrical components ● Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following. ● Brake function ●...
  • Page 171: Engine (Ignition) Switch (Vehicles With Smart Key System)

    2-1. Driving procedures Engine (ignition) switch (vehicles with smart key system) Performing the following operations when carrying the electronic key on your person starts the engine or changes “ENGINE START STOP” switch modes. ■ Starting the engine STEP Check that the parking brake is set. STEP Check that the shift lever is set in “P”.
  • Page 172 2-1. Driving procedures ■ Changing “ENGINE START STOP” switch mode Modes can be changed by pressing the “ENGINE START STOP” switch with the brake pedal released. (The mode changes each time the switch is pressed.) Emergency flashers can be used. ACCESSORY mode Some electrical components such as the audio system can...
  • Page 173 ■ If the engine does not start The engine immobilizer system may not have been deactivated. (P. 108) Contact your Toyota dealer. ■ When the “ENGINE START STOP” switch indicator flashes in amber The system may be malfunctioning. Have the vehicle inspected by your Toyota dealer immediately.
  • Page 174 TION ON mode for long periods without the engine running. ■ When starting the engine ● Do not race a cold engine. ● If the engine becomes difficult to start or stalls frequently, have your vehi- cle checked by your Toyota dealer immediately. VENZA_OM_OM73019U_(U)
  • Page 175: Engine (Ignition) Switch (Vehicles Without Smart Key System)

    2-1. Driving procedures Engine (ignition) switch (vehicles without smart key system) ■ Starting the engine STEP Check that the parking brake is set. STEP Check that the shift lever is set in “P”. STEP Sit in the driver’s seat and firmly depress the brake pedal. STEP Turn the engine switch to the “START”...
  • Page 176 2-1. Driving procedures ■ Turning the key from “ACC” to “LOCK” STEP Shift the shift lever to “P”. STEP Push in the key and turn to the “LOCK” position. ■ When the steering lock cannot be released When starting the engine, the engine switch may seem stuck in the “LOCK”...
  • Page 177 2-1. Driving procedures CAUTION ■ When starting the engine Always start the engine while sitting in the driver’s seat. Do not depress the accelerator pedal while starting the engine under any circumstances. Doing so may cause an accident resulting in death or serious injury. ■...
  • Page 178: Automatic Transmission

    2-1. Driving procedures Automatic transmission Select a shift position appropriate for the driving conditions. ■ Shifting the shift lever Vehicles with smart key system: While the “ENGINE START STOP” switch is in IGNITION ON mode, depress the brake pedal and move the shift lever.
  • Page 179 2-1. Driving procedures ■ Shift position uses Shift position Function Parking the vehicle or starting the engine Reversing Neutral Normal driving S mode driving (P. 180) : Shifting to the D position allows the system to select a gear suitable for the driving conditions.
  • Page 180 2-1. Driving procedures Changing shift ranges in S mode Shift the shift lever to the S mode driving position and operate the shift lever. Upshifting Downshifting The initial shift range in S mode is set automatically to 5 or 4 accord- ing to vehicle speed.
  • Page 181 2-1. Driving procedures ■ Shift ranges and their functions ● Automatically selecting gears between 1 and 6 according to vehicle speed and driving condition. (However the gear is limited according to selected shift range.) ● You can choose from 6 levels of engine braking force. ●...
  • Page 182 S mode driving position This may indicate a malfunction in the automatic transmission system. Have the vehicle inspected by your Toyota dealer immediately. (In this situation, the transmission will operate in the same manner as when the shift lever is in D.) ■...
  • Page 183: Turn Signal Lever

    2-1. Driving procedures Turn signal lever Right turn Left turn Move and hold the lever partway to signal a lane change. The right hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change.
  • Page 184: Parking Brake

    2-1. Driving procedures Parking brake Sets the parking brake (Depressing the pedal again releases the parking brake.) U.S.A. Canada : Fully depress the parking brake pedal with your left foot while depressing the brake pedal with your right foot. ■ Usage in winter time P.
  • Page 185: Horn

    2-1. Driving procedures Horn To sound the horn, press on or close to the mark. ■ After adjusting the steering wheel Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. (P.
  • Page 186: 2-2. Instrument Cluster

    2-2. Instrument cluster Gauges and meters Vehicles with smart key system The following gauges, meters and display illuminate when the “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system The following gauges, meters and displays illuminate when the engine switch is in the “ON”...
  • Page 187 2-2. Instrument cluster Odometer/trip meter and trip meter reset button Switches between odometer and trip meter displays. Pushing and hold- ing the button will reset the trip meter when the trip meter is being dis- played. Odometer and trip meter Odometer: Displays the total distance the vehicle has been driven.
  • Page 188 2-2. Instrument cluster NOTICE ■ To prevent damage to the engine and its components ● Do not let the indicator needle of the tachometer enter the red zone, which indicates the maximum engine speed. ● The engine may be overheating if the engine coolant temperature gauge is in the red zone (“H”).
  • Page 189: Indicators And Warning Lights

    2-2. Instrument cluster Indicators and warning lights The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems. For the purpose of explanation, the following illustration displays all indicators and warning lights illuminated.
  • Page 190 2-2. Instrument cluster ■ Indicators The indicators inform the driver of the operating state of the vehicle’s various systems. Turn signal indicator Cruise control “SET” (P. 183) indicator (P. 227) 1, 2 Headlight high beam Slip indicator (P. 239) indicator (P. 209) Headlight indicator VSC OFF indicator (P.
  • Page 191 Have the vehicle inspected by your Toyota dealer. : The indicator flashes to indicate that the system is operating.
  • Page 192: Multi-Information Display (Tft Type)

    2-2. Instrument cluster Multi-information display (TFT type) The multi-information display presents the driver with a variety of driving-related data, including the clock and current outside temper- ature. ● Clock (P. 197) Indicates and sets the time. ● Outside temperature Indicates the outside temperature. The temperature range that can be displayed is from -40°F (-40°C) to 122°F (50°C).
  • Page 193 2-2. Instrument cluster Switching the display “INFO” button “SELECT RESET” button To reset the functions below, press the “SELECT RESET” but- ton. • Average Fuel Economy • Average Speed • Trip Timer “SETUP” button Trip information Display items can be switched by pressing the “INFO” button. ■...
  • Page 194 2-2. Instrument cluster ■ Distance to Empty Displays the estimated maximum distance that can be driven with the quantity of fuel remaining. ● This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that dis- played.
  • Page 195 2-2. Instrument cluster ■ Trip Timer Displays the elapsed time since the timer was reset. The timer only functions when the engine is running. The timer can be started and paused by pressing the “SELECT RESET” button, and reset by pressing and holding the “SELECT RESET” button when the trip timer is displayed.
  • Page 196 2-2. Instrument cluster Setting up the displays STEP Press the “SETUP” button while the vehicle is stopped. The “Custom Settings” screen is displayed on the multi-information display. If left idle for approximately 10 seconds, the display will revert to the previous screen.
  • Page 197 2-2. Instrument cluster ■ Setting the clock STEP Select “Clock” on the “Display Settings” screen, and press the “SELECT RESET” button. Press the “INFO” button to adjust STEP the hours and the “SETUP” but- ton to adjust the minutes. Press and hold the buttons to adjust the time more quickly.
  • Page 198 2-2. Instrument cluster ■ Selecting the language STEP Select “Language” on the “Display Settings” screen, and press the “SELECT RESET” button. Select the language you want to STEP read by pressing the “INFO” or “SETUP” button. Press the “SELECT RESET” but- ton to set the language.
  • Page 199 2-2. Instrument cluster When a 2-line layout is selected STEP STEP , the “Layout” screen is displayed. First, using the “INFO” and “SETUP” buttons, select the item you wish to display in the first line, and then press the “SELECT RESET” button. Using the “INFO”...
  • Page 200 2-2. Instrument cluster ● Setting the brightness Select “Brightness” STEP “Screen Settings” screen, and press the “SELECT RESET” but- ton. Press the “INFO” or “SETUP” STEP button to adjust the brightness. +: Brighter -: Darker Press the “SELECT RESET” but- ton to exit screen.
  • Page 201 2-2. Instrument cluster ● Setting the contrast Select “Contrast” on the “Screen STEP Settings” screen, and press the “SELECT RESET” button. Press the “INFO” or “SETUP” STEP button to adjust the contrast. +: Strengthen -: Weaken Press the “SELECT RESET” but- ton to exit screen.
  • Page 202 2-2. Instrument cluster ■ If the vehicle is moved while settings are being changed on the multi- information display If the vehicle speed exceeds approxi- mately 3 mph (5 km/h) while the settings are being changed, “Please Stop Vehicle to Change Settings” will be displayed on the multi-information display, and setting mode will exit after several seconds.
  • Page 203 2-2. Instrument cluster ■ When “--”, “E” or “F” is displayed on the outside temperature display The system may be malfunctioning. Take your vehicle to your Toyota dealer. ■ Outside temperature display In the following situations, the correct outside temperature may not be dis- played, or the display may take longer than normal to change.
  • Page 204: Multi-Information Display (Lcd Type)

    2-2. Instrument cluster Multi-information display (LCD type) The multi-information display presents the driver with a variety of driving-related data, including the clock and current outside temper- ature. ● Clock (P. 206) Indicates and sets the time. ● Outside temperature Indicates the outside temperature. The temperature range that can be displayed is from -40°F (-40°C) to 122°F (50°C).
  • Page 205 2-2. Instrument cluster Switching the display “INFO-CLOCK” button “RESET-H” button To reset the functions below, press the “RESET-H” button. • Average fuel consumption • Average vehicle speed “US/M-M” button Trip information Display items can be switched by pressing the “INFO-CLOCK” but- ton.
  • Page 206 2-2. Instrument cluster ■ Driving range (RANGE) Displays the estimated maximum distance that can be driven with the quantity of fuel remaining. ● This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that dis- played.
  • Page 207 ■ When “--”, “E” or “F” is displayed on the outside temperature display The system may be malfunctioning. Take your vehicle to your Toyota dealer. ■ Outside temperature display In the following situations, the correct outside temperature may not be dis- played, or the display may take longer than normal to change.
  • Page 208: 2-3. Operating The Lights And Wipers

    2-3. Operating the lights and wipers Headlight switch The headlights can be operated manually or automatically. Turning the end of the lever turns on the lights as follows. Type A The daytime running lights turn on. (Type B only) The headlights, park- ing lights, daytime run- ning lights and so on turn on and off auto-...
  • Page 209 2-3. Operating the lights and wipers Turning on the high beam headlights With the headlights on, push the lever forward to turn on the high beams. Vehicles with Automatic High Beam: When the light switch is in position, the Automatic High Beam system will be acti- vated.
  • Page 210 2-3. Operating the lights and wipers ■ Daytime running light system ● To make your vehicle more visible to others, the high beam headlights turn on automatically at a reduced intensity (vehicles with halogen head- lights) or the LED daytime running lights turn on automatically (vehicles with discharge headlights) whenever the engine is started and the park- ing brake is released.
  • Page 211 2-3. Operating the lights and wipers Vehicles without smart key system ● When the headlights are on: The headlights and tail lights turn off 30 seconds after a door is opened and closed if the engine switch has been switched to “ACC” or “LOCK” position. ●...
  • Page 212: Automatic High Beam

    2-3. Operating the lights and wipers  Automatic High Beam The Automatic High Beam uses an in-vehicle camera sensor to assess the brightness of streetlights, the lights of oncoming and preceding vehicles, etc., and automatically turns high beam on or off as necessary.
  • Page 213 2-3. Operating the lights and wipers ■ Turning the high beam on/off manually Switching to low beam Pull the lever to original posi- tion. Switching to high beam Turn the light switch to position. VENZA_OM_OM73019U_(U)
  • Page 214 2-3. Operating the lights and wipers ■ High beam automatic turning on or off conditions When all of the following conditions are fulfilled, high beam will be automatically turned on (after approximately 1 second): ● Vehicle speed is above approximately 20 mph (32 km/h). ●...
  • Page 215 2-3. Operating the lights and wipers ■ Limitations of the Automatic High Beam Do not rely on the Automatic High Beam. Always drive safely, taking care to observe your surroundings and turning high beam on or off manually if nec- essary.
  • Page 216 2-3. Operating the lights and wipers ● In the situations below, the system may not be able to correctly detect the surrounding brightness levels, and may flash or expose nearby pedestri- ans to the high beam. Therefore, you should consider turning the high beam on or off manually rather than relying on the Automatic High Beam system.
  • Page 217 2-3. Operating the lights and wipers ■ If the Automatic High Beam indicator flashes... It may indicate a malfunction in the system. Contact your Toyota dealer. ■ Customization The Automatic High Beam can be turned off. (Customizable features P. 519) ■...
  • Page 218 Do not install a parking tag or any other accessories near or around the inside rear view mirror and the camera sensor. ● Do not overload the vehicle. ● Do not modify the vehicle. ● Do not replace windshield with a non-genuine windshield. Contact your Toyota dealer. VENZA_OM_OM73019U_(U)
  • Page 219: Fog Light Switch

    2-3. Operating the lights and wipers Fog light switch The fog lights improve visibility in difficult driving conditions, such as in rain or fog. The fog lights can be used when the headlights are on low beam. Type A VENZA_OM_OM73019U_(U)
  • Page 220 2-3. Operating the lights and wipers Type B VENZA_OM_OM73019U_(U)
  • Page 221: Windshield Wipers And Washer

    2-3. Operating the lights and wipers Windshield wipers and washer Wiper intervals can be adjusted for intermittent operation (when is selected). Type A Intermittent wiper operation speed wiper operation High speed wiper operation Temporary operation Increases the intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency VENZA_OM_OM73019U_(U)
  • Page 222 2-3. Operating the lights and wipers Wash/wipe operation Wipers operate automatically. Type B Intermittent wiper operation speed wiper operation High speed wiper operation Temporary operation VENZA_OM_OM73019U_(U)
  • Page 223 2-3. Operating the lights and wipers Increases the intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency Wash/wipe operation Wipers operate automatically. VENZA_OM_OM73019U_(U)
  • Page 224 2-3. Operating the lights and wipers ■ The windshield wiper and washer can be operated when Vehicles with smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ON” position. ■...
  • Page 225: Rear Window Wiper And Washer

    2-3. Operating the lights and wipers Rear window wiper and washer Type A Intermittent window wiper operation Normal window wiper operation Washer/wiper dual operation Washer/wiper dual operation VENZA_OM_OM73019U_(U)
  • Page 226 2-3. Operating the lights and wipers Type B Intermittent window wiper operation Normal window wiper operation Washer/wiper dual operation Washer/wiper dual operation ■ The rear window wiper and washer can be operated when Vehicles with smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ON”...
  • Page 227: Using Other Driving Systems Cruise Control

    2-4. Using other driving systems Cruise control Use the cruise control to maintain a set speed without depressing the accelerator pedal. Indicators Cruise control switch ■ Set the vehicle speed STEP Press the “ON-OFF” button to activate the cruise control. Cruise control indicator will come on.
  • Page 228 2-4. Using other driving systems ■ Adjusting the speed setting To change the set speed, operate the lever until the desired set speed is obtained. Increases speed Decreases speed Fine adjustment: Momentarily move the lever in the desired direction. Large adjustment: Hold the lever in the desired direction.
  • Page 229 2-4. Using other driving systems ■ Canceling and resuming the constant speed control Pulling the lever toward you cancels the constant speed control. The speed setting is also can- celed when the brakes are applied. Pushing lever resumes constant speed control. Resuming is available when the vehicle speed is more than approximately 25 mph (40 km/h).
  • Page 230 If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer. CAUTION ■...
  • Page 231: Intuitive Parking Assist

    2-4. Using other driving systems  Intuitive parking assist The distance from your vehicle to nearby obstacles when parallel parking or maneuvering into a garage is measured by the sensors and communicated via the multi-information display and a buzzer. Always check the surrounding area when using this system. ■...
  • Page 232 2-4. Using other driving systems Display When the sensors detect an obstacle, a graphic is shown on the multi information display depending on the position and distance to the obstacle. Front corner sensor operation Rear corner sensor operation Back sensor operation VENZA_OM_OM73019U_(U)
  • Page 233 2-4. Using other driving systems The distance display and buzzer When a sensor detects an obstacle, the direction of and the approxi- mate distance to the obstacle are displayed and the buzzer sounds. ■ Corner sensor operation and distance to an obstacle The system operates when the vehicle approaches within the fol- lowing distances to an obstacle.
  • Page 234 2-4. Using other driving systems ■ Back sensor operation and distance to an obstacle The system operates when the vehicle approaches within the fol- lowing distances to an obstacle. The indicator flashes and the buzzer sounds when the system is operating. Approximate distance to obstacle Indicator and buzzer / Color 4.9 to 2.0 ft.
  • Page 235 2-4. Using other driving systems Detection range of the sensors Approximately 1.6 ft. (50 cm) Approximately 4.9 ft. (150 cm) Approximately 2.0 ft. (60 cm) The diagram shows the detection range of the sensors. Note that the sensors cannot detect obsta- cles that are extremely close to the vehicle.
  • Page 236 • The vehicle is approaching a tall or curved curb. • In harsh sunlight or intense cold weather. • A non-genuine Toyota suspension (lowered suspension etc.) is installed. In addition to the examples above, there are instances in which, because of their shapes, signs and other objects may be judged by the sensor to be closer than they are.
  • Page 237 2-4. Using other driving systems ■ Certification (Canada only) This ISM device complies with Canadian ICES-001. CAUTION ■ Caution when using the Intuitive parking assist Observe the following precautions. Failing to do so may result in the vehicle being unable to be driven safely and possibly cause an accident.
  • Page 238: Driving Assist Systems

    2-4. Using other driving systems Driving assist systems To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. ■...
  • Page 239 2-4. Using other driving systems ■ Active Torque Control 4WD (if equipped) Automatically switches from front-wheel drive to AWD (All- Wheel Drive) according to driving conditions, helping to ensure reliable handling and stability. Examples of conditions where the system will switch to AWD are when cornering, going uphill, starting off or accelerating, and when the road surface is slippery due to snow or rain etc.
  • Page 240 2-4. Using other driving systems Disabling the TRAC system If the vehicle gets stuck in mud, dirt or snow, the TRAC system may reduce power from the engine to the wheels. Pressing to turn the system off may make it easier for you to rock the vehicle in order to free it.
  • Page 241 2-4. Using other driving systems ■ When the “TRAC OFF” indicator light comes on even if the VSC OFF switch has not been pressed TRAC and hill-start assist control cannot be operated. Contact your Toyota dealer. ■ Automatic reactivation of TRAC and VSC...
  • Page 242 2-4. Using other driving systems ■ EPS operation sound When the steering wheel is operated, a motor sound (whirring sound) may be heard. This does not indicate a malfunction. ■ Reduced effectiveness of EPS system The effectiveness of EPS system is reduced to prevent the system from overheating when there is frequent steering input over an extended period of time.
  • Page 243 In addition, make sure that the tires are inflated to the speci- fied tire pressure level. The ABS and VSC will not function correctly if different tires are fitted on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels. ■ Handling of tires and suspension Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause the system to malfunction.
  • Page 244: Hill-Start Assist Control

    2-4. Using other driving systems Hill-start assist control Hill-start assist control helps to prevent the vehicle from rolling backwards when starting on incline or slippery slope. To engage hill-start assist con- trol, further depress the brake pedal when the vehicle is stopped completely.
  • Page 245 • The shift lever is moved to “P”. • The parking brake is applied. • The brake pedal is depressed again. ■ If the slip indicator comes on... It may indicate a malfunction in the system. Contact your Toyota dealer. CAUTION ■ Hill-start assist control ●...
  • Page 246: Driving Information Utility Vehicle Precautions

    2-5. Driving information Utility vehicle precautions This vehicle belongs to the utility vehicle class, which has higher ground clearance and narrower tread in relation to the height of its center of gravity. Utility vehicle feature ● Specific design characteristics give it a higher center of gravity than ordinary passenger cars.
  • Page 247 2-5. Driving information CAUTION ■ Utility vehicle precautions Always observe the following precautions to help minimize the risk of serious personal injury or damage to your vehicle: ● In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.
  • Page 248 2-5. Driving information Off-road driving Your vehicle is not designed to be driven off-road. However, in the event that off-road driving cannot be avoided, please observe the fol- lowing precautions to help avoid the areas prohibited to vehicles. ● Drive your vehicle only in areas where off-road vehicles are permit- ted to travel.
  • Page 249 2-5. Driving information CAUTION ■ Off-road driving precautions Always observe the following precautions to help minimize the risk of serious personal injury or damage to your vehicle: ● Drive carefully when off the road. Do not take unnecessary risks by driving in dangerous places.
  • Page 250 2-5. Driving information NOTICE ■ To prevent the water damage Take all necessary safety measures to ensure that water damage to the engine or other components does not occur. ● Water entering the engine air intake will cause severe engine damage. ●...
  • Page 251: Cargo And Luggage

    2-5. Driving information Cargo and luggage Take notice of the following information about storage precau- tions, cargo capacity and load. ● Stow cargo and luggage in the luggage compartment when- ever possible. Be sure all items are secured in place. ●...
  • Page 252 2-5. Driving information Capacity and distribution Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) — (Total weight of occupants) Steps for Determining Correct Load Limit— (1) Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.”...
  • Page 253 2-5. Driving information Calculation formula for your vehicle Cargo capacity Total load capacity (vehicle capacity weight) (P. 486) When 2 people with the combined weight of A lb. (kg) are riding in your vehicle, which has a total load capacity (vehicle capacity weight) of B lb.
  • Page 254 2-5. Driving information CAUTION ■ Things that must not be carried in the luggage compartment The following things may cause a fire if loaded in the luggage compart- ment. ● Receptacles containing gasoline ● Aerosol cans ■ Storage precautions Observe the following precautions. Failing to do so may result in death or serious injury.
  • Page 255 2-5. Driving information CAUTION ■ Weight of the load ● Do not exceed the maximum axle weight rating or the total vehicle weight rating. ● Even if the total load of occupant’s weight and the cargo load is less than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking control which may cause death or serious injury.
  • Page 256: Vehicle Load Limits

    2-5. Driving information Vehicle load limits Vehicle load limits include total load capacity, seating capacity, Trailer Weight Rating (TWR) and cargo capacity. Total load capacity (Vehicle capacity weight): P. 486 ■ Total load capacity means the combined weight of occupants, cargo and luggage.
  • Page 257 2-5. Driving information ■ Total load capacity and seating capacity These details are also described on the tire and loading information label. (P. 389) CAUTION ■ Overloading the vehicle Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.
  • Page 258: Winter Driving Tips

    2-5. Driving information Winter driving tips Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations ● Use fluids that are appropriate to the prevailing outside tem- peratures.
  • Page 259 2-5. Driving information ■ Before driving the vehicle Perform the following according to the driving conditions. ● Do not try to forcibly open a window or move a wiper that is frozen. Pour warm water over the frozen area to melt the ice. Wipe away the water immediately to prevent it from freezing.
  • Page 260 2-5. Driving information Selection tire chains Use the correct tire chain size when mounting the tire chains. Chain size is regulated for each tire size. Side chain: 0.12 in. (3.0 mm) 1.18 in. (30.0 mm) 0.39 in. (10.0 mm) Cross chain: 0.16 in.
  • Page 261 2-5. Driving information CAUTION ■ Driving with snow tires Observe the following precautions to reduce the risk of accidents. Failing to do so may result in a loss of vehicle control and cause death or serious injury. ● Use tires of the size specified for your vehicle. ●...
  • Page 262 NOTICE ■ Repairing or replacing snow tires Request repairs of and obtain replacement snow tires from Toyota deal- ers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the operation of the tire pressure warning valves and transmitters.
  • Page 263: Trailer Towing

    To tow a trailer safely, use extreme care and drive the vehicle in accordance with your trailer’s characteristics and operating condi- tions. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. Contact your Toyota dealer for further information about additional requirements such as a towing kit, etc.
  • Page 264 2-5. Driving information Towing related terms ■ GCWR (Gross Combination Weight Rating) 2GR-FE engine (Without towing package) and 1AR-FE engine The maximum allowable gross combination weight. The gross combination weight is the sum of the total vehicle weight (including the occupants, cargo and any optional equipment installed on the vehicle) and the weight of the trailer being towed (including the...
  • Page 265 2-5. Driving information ■ GVWR (Gross Vehicle Weight Rating) 2GR-FE engine (Without towing package) and 1AR-FE engine The maximum allowable gross vehicle weight. The gross vehicle weight is the total weight of the vehicle. When towing a trailer, it is the sum of the vehicle weight (including the occupants, cargo and any optional equipment installed on the vehicle) and the...
  • Page 266 2-5. Driving information ■ GAWR (Gross Axle Weight Rating) 2GR-FE engine (Without towing package) and 1AR-FE engine The maximum allowable gross Front GAWR axle weight. The gross axle weight is the load placed on each axle (front and rear). Rear GAWR 2GR-FE engine (With towing package) Front GAWR Rear GAWR...
  • Page 267 2-5. Driving information ■ TWR (Trailer Weight Rating) 2GR-FE engine (Without towing package) and 1AR-FE engine The maximum allowable gross (With brakes) trailer weight. The gross trailer weight is the sum of the trailer weight and the weight of the cargo in the trailer.
  • Page 268 2-5. Driving information ■ Unbraked TWR (Unbraked Trailer Weight Rating) The trailer weight rating for tow- (Without brakes) ing a trailer without a trailer ser- vice brake system. ■ Tongue Weight 2GR-FE engine (Without towing package) and 1AR-FE engine The load placed on the trailer hitch ball.
  • Page 269 2-5. Driving information Weight limits ● The gross trailer weight must never exceed TWR described in the table. (P. 270) ● The gross combination weight must never exceed the GCWR described in the table. (P. 270) ● The gross vehicle weight must never exceed the GVWR indi- cated Certification...
  • Page 270 2-5. Driving information GCWR, TWR and Unbraked TWR Confirm that the gross trailer weight, gross combination weight, gross vehicle weight, gross axle weight and tongue weight are all within the limits.  ■ GCWR and TWR Vehicles without towing package Driving Engine GCWR...
  • Page 271 2-5. Driving information Trailer Tongue Weight ● A recommended tongue weight varies in accordance with the types of trailers or towing as described below. ● To ensure the recommended values shown below, the trailer must be loaded by referring to the following instructions. •...
  • Page 272 Toyota hitch/bracket for your vehicle. For details, contact your Toyota dealer. ● If you wish to install a trailer hitch, contact your Toyota dealer. ● Use only a hitch that conforms to the gross trailer weight require- ment of your vehicle.
  • Page 273 2-5. Driving information Selecting trailer ball Use the correct trailer ball for your application. Trailer ball load rating Matches or exceeds the gross trailer weight rating of the trailer. Ball diameter Matches the size of the trailer coupler. Most couplers stamped with the required trailer ball size.
  • Page 274 2-5. Driving information Positions for towing hitch receiver and hitch ball Weight carrying ball position: 46.5 in. (1180 mm) Hitch receiver pin hole posi- tion: 39.2 in. (996.5 mm) Connecting trailer lights Please consult your dealer when installing trailer lights, as incorrect installation may cause damage to the vehicle’s lights.
  • Page 275 ● Speed limits for towing a trailer vary by state or province. Do not exceed the posted towing speed limit. ● Toyota recommends that the vehicle-trailer speed limit is 65 mph (104 km/h) on a flat, straight, dry road. Do not exceed this limit, the posted towing speed limit or the speed limit for your trailer as set forth in your trailer owner’s manual, whichever is lowest.
  • Page 276 2-5. Driving information ● As stopping distance is increased when towing a trailer, vehicle-to- vehicle distance should be increased. For each 10 mph (16 km/h) of speed, allow at least one vehicle and trailer length. ● Avoid sudden braking as you may skid, resulting in the trailer jack- knifing and a loss of vehicle control.
  • Page 277 2-5. Driving information ● Avoid holding the brake pedal down too long or applying the brakes too frequently. This could cause the brakes to overheat and result in reduced braking efficiency. ● Due to the added load of the trailer, your vehicle’s engine may overheat on hot days (at temperatures over 85°F [30°C]) when driving up a long or steep grade.
  • Page 278 2-5. Driving information ● When restarting after parking on a slope: STEP With the transmission in P, start the engine. Be sure to keep the brake pedal pressed. STEP Shift into a forward gear. If reversing, shift into R. STEP Release the parking brake and brake pedal, and slowly pull or back away from the wheel blocks.
  • Page 279 Break-in schedule If your vehicle is new or equipped with any new power train components (such as an engine, transmission, differential or wheel bearing), Toyota rec- ommends that you do not tow a trailer until the vehicle has been driven for over 500 miles (800 km).
  • Page 280 2-5. Driving information ■ Maintenance ● If you tow a trailer, your vehicle will require more frequent maintenance due to the additional load. (See “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.) ● Retighten the fixing bolts of the towing ball and bracket after approxi- mately 600 miles (1000 km) of trailer towing.
  • Page 281 2-5. Driving information CAUTION ■ Trailer towing precautions To tow a trailer safely, use extreme care and drive the vehicle in accordance with the trailer’s characteristics and operating conditions. Failure to do so could cause an accident resulting in death or serious injury. Vehicle stability and braking performance are affected by trailer stability, brake setting and performance, and the hitch.
  • Page 282 2-5. Driving information CAUTION ■ To avoid accident or injury ● Do not use cruise control when towing. ● Slow down and downshift before descending steep or long downhill grades. Do not make sudden downshifts while descending steep or long downhill grades.
  • Page 283 NOTICE ■ When installing a trailer hitch Use only the position recommended by your Toyota dealer. Do not install the trailer hitch on the bumper; this may cause body damage. ■ Do not directly splice trailer lights Do not directly splice trailer lights.
  • Page 284: Dinghy Towing

    2-5. Driving information Dinghy towing Your vehicle is not designed to be dinghy towed (with four wheels on the ground) behind a motor home. NOTICE ■ To avoid serious damage to your vehicle Do not tow your vehicle with four wheels on the ground.
  • Page 285: Interior Features

    Interior features 3-1. Using the air conditioning 3-4. Using the storage features system and defogger List of storage features ......309 Automatic air • Glove box....... 310 conditioning system ..286 • Console boxes ....311 Rear window • Overhead console..313 defogger......
  • Page 286: Using The Air Conditioning System And Defogger Automatic Air Conditioning System

    3-1. Using the air conditioning system and defogger Automatic air conditioning system Airflow and outlets are automatically adjusted according to the tem- perature setting. Control panel Fan speed Changes the air Driver’s side temperature control outlets used dial and automatic mode switch Passenger’s side temperature control dial...
  • Page 287 3-1. Using the air conditioning system and defogger Multi-information display (TFT type) Automatic mode indicator Airflow display Driver’s side Passenger’s side temperature temperature setting display setting display Air conditioning on indicator Fan speed display The settings display will differ according to the situation. If pressed while in automatic mode, the status of all settings will be dis- played for a number of seconds.
  • Page 288 3-1. Using the air conditioning system and defogger Using the automatic mode STEP Press The air conditioning system will begin to operate. In outside air or recirculated air mode, air outlets, fan speed and air conditioning on/ off are automatically adjusted according to the temperature setting. “AUTO”...
  • Page 289 3-1. Using the air conditioning system and defogger Adjusting the settings ■ Adjusting the temperature setting Turn the temperature control dial clockwise (warm) or counter- clockwise (cool). The air conditioning system switches between dual and simulta- neous modes each time is pressed.
  • Page 290 3-1. Using the air conditioning system and defogger ■ Adjusting the fan speed Press “” (increase) or “” (decrease) on The fan speed is shown on the display. (7 levels) Pressing the button while in automatic mode will place the fan speed into manual mode.
  • Page 291 3-1. Using the air conditioning system and defogger Air flows to the upper body and feet. Mainly air flows to the feet. Air flows to the feet and the windshield defogger operates. ■ Switching between outside air and recirculated air modes Press The mode switches between outside air mode (indicator off) and recirculated air mode (indicator on) each time the button is pressed.
  • Page 292 3-1. Using the air conditioning system and defogger Defogging the windshield Press The air conditioning system con- trol operates automatically. Recirculated air mode will auto- matically switch to outside air mode. It is not possible to return to recirculated air mode when the switch is on.
  • Page 293 3-1. Using the air conditioning system and defogger Front side outlets Direct air flow to the left or right, up or down. Turn the knob to open or close the vent. Rear center outlets Direct air flow to the left or right, up or down.
  • Page 294 3-1. Using the air conditioning system and defogger ■ Using the automatic mode Fan speed is adjusted automatically in accordance with the temperature set- ting and ambient conditions. As a result, the following may occur. ● Immediately after is pressed, the fan may stop for a while until warm or cool air is ready to flow.
  • Page 295 3-1. Using the air conditioning system and defogger ■ When outside temperature reaches approximately 32°F (0°C) The air conditioning system may not operate even when is pressed. ■ Air conditioning odors ● During use, various odors from inside and outside the vehicle may enter into and accumulate in the air conditioning system.
  • Page 296: Rear Window Defogger

    3-1. Using the air conditioning system and defogger Rear window defogger Clear the rear window using the defogger. On/off The defogger will automatically turn off after 15 or 60 minutes. This operation time changes according to the ambient tem- perature and vehicle speed. Pressing the switch again also turns the defogger off.
  • Page 297 3-1. Using the air conditioning system and defogger CAUTION ■ Outside rear view mirror defoggers and windshield wiper de-icer Do not touch the rear view mirror surfaces, the glass at the lower part of the windshield or to the side of the front pillars, as they can become very hot and burn you.
  • Page 298: 3-2. Using The Audio System

    3-2. Using the audio system Audio system types Vehicles with Display Audio system Type A Type B Refer to the “Display Audio System Owner’s Manual”. VENZA_OM_OM73019U_(U)
  • Page 299 3-2. Using the audio system Vehicles with a navigation system Canada Refer to the “Navigation System Owner’s Manual”. VENZA_OM_OM73019U_(U)
  • Page 300 3-2. Using the audio system Steering wheel switches Some audio features can be controlled using the switches on the steering wheel. For details, refer to the “Display Audio System Owner’s Manual” or “Navigation System Owner’s Manual”. Operation may differ and usage may not be possible with audio/navi- gation systems that are not compatible with the steering switches in this vehicle.
  • Page 301 3-2. Using the audio system ■ ® About Bluetooth (vehicles with Display Audio system) Bluetooth is a registered trademark of Bluetooth SIG. Inc. The Bluetooth wordmark and logo are owned by Bluetooth SIG. and permission has been granted to use the trademark of licensee Panasonic Corporation.
  • Page 302 3-2. Using the audio system CAUTION Properly shielded a grounded cables and connectors must be used for connection to host computer and / or peripherals in order to meet FCC emission limits. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
  • Page 303 3-2. Using the audio system CAUTION Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
  • Page 304: Using The Aux Port/Usb Port

    3-2. Using the audio system Using the AUX port/USB port This port can be used to connect a portable audio device and listen to it through the vehicle’s speakers. Open the cover. STEP STEP Connect the portable audio device. ■ Operating portable audio devices connected to the audio system The volume can be adjusted using the vehicle’s audio controls.
  • Page 305: 3-3. Using The Interior Lights

    3-3. Using the interior lights Interior lights list Your Toyota is equipped with the illuminated entry system to assist in entering the vehicle. Due to the function of the system, the lights shown in the following illustration automatically turn on/off accord-...
  • Page 306: Personal/Interior Light Main Switch

    3-3. Using the interior lights Personal/interior light main switch Personal/interior lights “ENGINE START STOP” switch light (vehicles with smart key system) or engine switch light (vehicles without smart key sys- tem) Door courtesy lights Luggage compartment light Outer foot lights Personal/interior light main switch “OFF”...
  • Page 307: Personal/Interior Lights

    3-3. Using the interior lights Personal/interior lights and luggage compartment light Personal/interior lights Front On/off The illuminated entry system is activated even if the light is turned off when the personal/inte- rior light main switch is in door position. Rear On/off The illuminated entry system is activated even if the light is...
  • Page 308 3-3. Using the interior lights ■ Adjusting the rear personal/interior lights angle Push the edge of the light lens. ■ To prevent the battery from being discharged Vehicles with smart key system If the personal/interior lights and “ENGINE START STOP” switch light remain on when the door is not fully closed and the personal/interior light main switch is in door position, the lights will go off automatically after 20 minutes.
  • Page 309: 3-4. Using The Storage Features

    3-4. Using the storage features List of storage features Bottle holders Door pockets Auxiliary boxes Overhead console Console boxes Glove box Cup holders VENZA_OM_OM73019U_(U)
  • Page 310: Glove Box

    3-4. Using the storage features Glove box CAUTION ■ Items that should not be left in the storage spaces Do not leave glasses, lighters or spray cans in the storage spaces, as this may cause the following when cabin temperature becomes high: ●...
  • Page 311: Console Boxes

    3-4. Using the storage features Console boxes Console boxes Front Press the tab and slide to open. Rear Pull up the lever to release the lock. Slide the armrest fully rear- ward. Lift the armrest to open. VENZA_OM_OM73019U_(U)
  • Page 312 3-4. Using the storage features Console boxes ■ When using the rear console box lid as an armrest If necessary, the console box lid can slide forward. Pull the lid forward while pulling up the lever. ■ Tray in the rear console box The tray slides forward/backward and can be removed.
  • Page 313: Overhead Console

    3-4. Using the storage features Overhead console Overhead console Push the lid. The overhead console is useful temporarily storing small items. CAUTION ■ While driving Do not leave the overhead console open. Items may fall out and cause injury. VENZA_OM_OM73019U_(U)
  • Page 314: Cup Holders

    3-4. Using the storage features Cup holders Cup holders Front Rear Pull down the armrest and open the lid. VENZA_OM_OM73019U_(U)
  • Page 315 3-4. Using the storage features Cup holders ■ Adjusting size of the front cup holder Remove the adapter. CAUTION ■ Items unsuitable for the cup holder Do not place anything other than cups or aluminum cans in the cup holders. Other items may be thrown out of the holders in the event of an accident or sudden braking and cause injury.
  • Page 316: Bottle Holders

    3-4. Using the storage features Bottle holders Bottle holders For front seats For rear seats NOTICE ■ Items that should not be stowed in the bottle holders Put the cap on before stowing a bottle. Do not place open bottles in the bot- tle holders, or glasses and paper cups containing liquid.
  • Page 317: Auxiliary Boxes

    3-4. Using the storage features Auxiliary boxes Auxiliary boxes Type A (driver’s side instrument panel) Push down the knob. Type B (front console) Lift the lid. Type C (front console) Lift the lid. VENZA_OM_OM73019U_(U)
  • Page 318 3-4. Using the storage features Auxiliary boxes Type D (front passenger’s side instrument panel) ■ Coin holder (type A) Nickels, quarters and dimes can be stored separately. VENZA_OM_OM73019U_(U)
  • Page 319 3-4. Using the storage features Auxiliary boxes ■ Cable pass-through (type B and C) Type B The auxiliary boxes of the front console are provided with a hole that allows cables to be passed from the power outlet and AUX port/USB port. For type B, push in the push bar before routing the cables.
  • Page 320: 3-5. Other Interior Features

    3-5. Other interior features Sun visors Forward position: Flip down. Side position: Flip down, unhook, and swing to the side. VENZA_OM_OM73019U_(U)
  • Page 321: Vanity Mirror

    3-5. Other interior features Vanity mirror Slide the cover. The light turns on when the cover is opened. VENZA_OM_OM73019U_(U)
  • Page 322: Power Outlets

    3-5. Other interior features Power outlets The power outlets can be used for 12V accessories that run on less than 10A. Console box Front passenger’s side instrument panel Luggage compartment VENZA_OM_OM73019U_(U)
  • Page 323 3-5. Other interior features ■ The power outlets can be used when Vehicles with smart key system The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ACC” or “ON” position. NOTICE ■...
  • Page 324: Seat Heaters

    3-5. Other interior features  Seat heaters For driver’s seat For front passenger’s seat The indicator light comes on. Adjusts the seat tempera- ture The further you turn the dial upward, the warmer the seat becomes. ■ The seat heaters can be used when Vehicles with smart key system The “ENGINE START STOP”...
  • Page 325 3-5. Other interior features CAUTION ■ Burns ● Use caution when seating the following persons in a seat with the seat heater on to avoid the possibility of burns: • Babies, small children, the elderly, the sick and the disabled •...
  • Page 326: Armrest

    3-5. Other interior features Armrest Front Lift the lever up and slide the armrest. Rear Pull the armrest down for use. NOTICE ■ To prevent damage to the armrest Do not place too much strain on the armrest. VENZA_OM_OM73019U_(U)
  • Page 327: Assist Grips (Folding Type)

    3-5. Other interior features Assist grips (folding type) An assist grip installed on the ceiling can be used to support your body while sitting on the seat. CAUTION ■ Assist grip Do not use the assist grip when getting in or out of the vehicle or rising from your seat.
  • Page 328: Floor Mats

    3-5. Other interior features Floor mats Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet. Insert the retaining hooks STEP (clips) into the floor mat eye- lets.
  • Page 329 When installing the driver’s floor mat ● Do not use floor mats designed for other models or different model year vehicles, even if they are Toyota Genuine floor mats. ● Only use floor mats designed for the driver’s seat. ●...
  • Page 330: Luggage Compartment Features

    3-5. Other interior features Luggage compartment features ■ Cargo hooks Cargo hooks are provided for securing loose items. ■ Shopping bag hooks ■ Auxiliary box Lift the right side deck board. VENZA_OM_OM73019U_(U)
  • Page 331 3-5. Other interior features ■ Luggage cover Pull out the luggage cover and hook it on the anchors. Removing luggage cover Retract the cover and release both ends, then lift it out. After removing the luggage cover, place it somewhere other than the passenger compartment.
  • Page 332: Garage Door Opener

    3-5. Other interior features Garage door opener The garage door opener can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, secu- rity systems, and other devices.  The garage door opener (HomeLink Universal Transceiver) is manufac- ...
  • Page 333 3-5. Other interior features ® ■ Programming HomeLink Point the remote control trans- STEP mitter for the device 1 to 3 in. (25  to 75 mm) from the HomeLink buttons.  Keep the HomeLink indicator light in view while programming. Press and hold one of the STEP ...
  • Page 334 3-5. Other interior features  Test the HomeLink operation STEP by pressing the newly pro- grammed button.  If a HomeLink button has been programmed for a garage door, check to see if the garage door opens and closes. If the garage door does not operate, see if your remote control transmitter is of the rolling code type.
  • Page 335 3-5. Other interior features ■ Programming a rolling code system If your device is rolling code equipped, follow the steps under the  heading “Programming HomeLink ” before proceeding with the steps listed below. STEP Locate the learn button on the ceiling mounted garage door opener motor.
  • Page 336  the remaining HomeLink buttons. ■ Programming other devices To program other devices such as home security systems, home door locks or lighting, contact your authorized Toyota dealer for assistance. ■ Reprogramming a button  The individual HomeLink buttons cannot be erased but can be reprogrammed.
  • Page 337 3-5. Other interior features ® Operating HomeLink   Press the appropriate HomeLink button. The HomeLink indicator light should come on.  The HomeLink compatible transceiver in your vehicle continues to send a signal for up to 20 seconds as long as the button is pressed. ®...
  • Page 338 3-5. Other interior features ■ Before programming ● Install a new battery in the remote control transmitter. ● The battery side of the remote control transmitter must be pointed away  from the HomeLink button. ■ Certification for the garage door opener FCC ID: CB2300NHL3 FCC ID: CB2281AHL4 NOTE:...
  • Page 339: Compass

    3-5. Other interior features Compass The compass on the inside rear view mirror indicates the direction in which the vehicle is heading. ■ Operation To turn the compass on or off, push and hold “AUTO” for longer than 3 seconds. ■...
  • Page 340 3-5. Other interior features Calibrating the compass Samoa: 5 Guam: 8 Saipan: 8 The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies according to the geographic position of the vehicle. If you cross over a map boundary shown in illustration, the compass will deviate.
  • Page 341 3-5. Other interior features ■ Deviation calibration STEP Stop the vehicle where it is safe to drive in a circle. Push and hold “AUTO” until a STEP number (1 to 15) appears on the compass display. STEP Press “AUTO”, and referring to the map above, select the number of the zone where you are.
  • Page 342 3-5. Other interior features ■ Conditions unfavorable to correct operation The compass may not show the correct direction in the following conditions: ● The vehicle is stopped immediately after turning. ● The vehicle is on an inclined surface. ● The vehicle is in a place where the earth’s magnetic field is subject to interference by artificial magnetic fields (underground car park/parking lot, under a steel tower, between buildings, roof car park/parking lot, near an intersection, near a large vehicle, etc.).
  • Page 343 3-5. Other interior features NOTICE ■ To avoid the compass malfunctions Do not place magnets or any metal objects near the inside rear view mirror. Doing this may cause a malfunction of the compass sensor. ■ To ensure normal operation of the compass ●...
  • Page 344 3-5. Other interior features VENZA_OM_OM73019U_(U)
  • Page 345: Maintenance And Care

    Maintenance and care 4-1. Maintenance and care Cleaning and protecting the vehicle exterior..346 Cleaning and protecting the vehicle interior..349 4-2. Maintenance Maintenance requirements ....352 General maintenance..355 Emission inspection and maintenance (I/M) programs......358 4-3. Do-it-yourself maintenance Do-it-yourself service precautions ....
  • Page 346: Cleaning And Protecting The Vehicle Exterior

    4-1. Maintenance and care Cleaning and protecting the vehicle exterior Perform the following to protect the vehicle and maintain it in prime condition. ● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust.
  • Page 347 4-1. Maintenance and care ■ High pressure car washes ● Do not allow the nozzles of the car wash to come within close proximity of the windows. ● Before car wash, check that the fuel filler door is closed. ■ Aluminum wheels ●...
  • Page 348 ■ If the windshield washer nozzle become blocked Contact your Toyota dealer. Do not try to clear it with a pin or other object. This may damage the nozzle. ■ Cleaning the exterior lights ●...
  • Page 349: Cleaning And Protecting The Vehicle Interior

    4-1. Maintenance and care Cleaning and protecting the vehicle interior The following procedures will help protect your vehicle’s interior and keep it in top condition: ■ Protecting the vehicle interior Remove dirt and dust using a vacuum cleaner. Wipe dirty sur- faces with a cloth dampened with lukewarm water.
  • Page 350 4-1. Maintenance and care ■ Caring for leather areas Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle’s interior. ■ Shampooing the carpets There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam.
  • Page 351 4-1. Maintenance and care NOTICE ■ Cleaning detergents ● Do not use the following types of detergent, as they may discolor the vehi- cle interior or cause streaks or damage to painted surfaces. • Non-seat portions: Organic substances such as benzene or gasoline, alkaline or acidic solutions, dye, or bleach.
  • Page 352: Maintenance Maintenance Requirements

    It is recommended that genuine Toyota parts be used for repair to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than a Toyota dealer performs repairs, confirm the war- ranty coverage.
  • Page 353 Continue to press and hold the trip meter reset button until the trip meter displays “000000”. ■ Allow inspection and repairs to be performed by a Toyota dealer ● Toyota technicians are well-trained specialists and are kept up to date with the latest service information.
  • Page 354 4-2. Maintenance CAUTION ■ Warning in handling of battery, oils, fuels, and fluids ● Engine exhaust, some of its constituents, and a wide variety of automobile components contain or emit chemicals known to the State of California to cause cancer and birth defects and other reproductive harm. Work in a well ventilated area.
  • Page 355: General Maintenance

    “Scheduled Maintenance Guide”, “Owner’s Manual Supplement”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice. Engine compartment Items...
  • Page 356 4-2. Maintenance Vehicle interior Items Check points • Moves smoothly (without uneven pedal Accelerator pedal effort or catching)? Automatic transmission • Can the vehicle be held securely on an “Park” mechanism incline with the shift lever in “P”? • Moves smoothly? Brake pedal •...
  • Page 357 4-2. Maintenance Vehicle exterior Items Check points Doors • Operate smoothly? Engine hood • The lock system works properly? Fluid leaks • Is there any leakage after parking? • Inflation pressure is correct? • Tire surfaces not worn or damaged? Tire •...
  • Page 358: Emission Inspection And Maintenance (I/M) Programs

    If the malfunction indicator lamp comes on The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/ M test and may need to be repaired. Contact your Toyota dealer to service the vehicle. ■...
  • Page 359: Do-It-Yourself Maintenance Do-It-Yourself Service Precautions

    Brake fluid level (P. 376) • Rag or paper towel • Funnel (used only for adding brake fluid) • “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non-silicate, non- amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology.
  • Page 360 4-3. Do-it-yourself maintenance Items Parts and tools • “Toyota Genuine Motor Oil” or equivalent Engine oil level (P. 369) • Rag or paper towel • Funnel (used only for adding engine oil) • Fuse with same amperage rating Fuses (P. 403) as original ...
  • Page 361 4-3. Do-it-yourself maintenance CAUTION The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury observe the following precautions. ■ When working on the engine compartment ● Keep hands, clothing, and tools away from the moving fan and engine drive belt.
  • Page 362 4-3. Do-it-yourself maintenance CAUTION ■ When working near the electric cooling fan or radiator grille Vehicles with smart key system Be sure the “ENGINE START STOP” switch is off. With the “ENGINE START STOP” switch in IGNITION ON mode, the electric cooling fan may automatically start to run if the air conditioning is on and/or if the coolant temperature is high.
  • Page 363: Hood

    4-3. Do-it-yourself maintenance Hood Release the lock from the inside of the vehicle to open the hood. Pull the hood release lever. STEP The hood will pop up slightly. Lift the hood catch and lift the STEP hood. Hold the hood open by insert- STEP ing the supporting rod into the slot.
  • Page 364 4-3. Do-it-yourself maintenance CAUTION ■ Pre-driving check Check that the hood is fully closed and locked. If the hood is not locked properly it may open while the vehicle is in motion and cause an accident, which may result in death or serious injury. ■...
  • Page 365: Positioning A Floor Jack

    4-3. Do-it-yourself maintenance Positioning a floor jack When raising your vehicle with a floor jack, position the jack cor- rectly. Improper placement may damage your vehicle or cause injury. Front Rear (2WD models) Rear (AWD models) VENZA_OM_OM73019U_(U)
  • Page 366 4-3. Do-it-yourself maintenance CAUTION ■ When raising your vehicle Make sure to observe the following to reduce the possibility of death or seri- ous injury. ● Lift up the vehicle using a floor jack such as the one shown in the illustra- tion.
  • Page 367: Engine Compartment

    4-3. Do-it-yourself maintenance Engine compartment 2GR-FE engine Engine coolant reservoir Battery (P. 378) (P. 373) Fuse box (P. 403) Engine oil filler cap Electric cooling fans (P. 371) Condenser (P. 375) Engine oil level dipstick Radiator (P. 375) (P. 369) Washer fluid tank Brake fluid reservoir (P.
  • Page 368 4-3. Do-it-yourself maintenance 1AR-FE engine Engine coolant reservoir Battery (P. 378) (P. 373) Fuse box (P. 403) Engine oil filler cap Electric cooling fans (P. 371) Condenser (P. 375) Engine oil level dipstick Radiator (P. 375) (P. 369) Washer fluid tank Brake fluid reservoir (P.
  • Page 369 4-3. Do-it-yourself maintenance Engine oil With the engine at operating temperature and turned off, check the oil level on the dipstick. ■ Checking the engine oil STEP Park the vehicle on level ground. After warming up the engine and turning it off, wait more than five minutes for the oil to drain back into the bottom of the engine.
  • Page 370 4-3. Do-it-yourself maintenance STEP Holding a rag under the end, pull the dipstick out and check the oil level. Flat dipstick Normal Excessive The shape of the dipstick may dif- fer depending on the type of vehi- cle or engine. Non-flat dipstick Normal Excessive...
  • Page 371 4-3. Do-it-yourself maintenance ■ Adding engine oil If the oil level is below or near the low level mark, add engine oil of the same type as already in the engine. Make sure to check the oil type and prepare the items needed before adding oil.
  • Page 372 Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal. ●...
  • Page 373 4-3. Do-it-yourself maintenance NOTICE ■ To prevent serious engine damage Check the oil level on regular basis. ■ When replacing the engine oil ● Be careful not to spill engine oil on the vehicle components. ● Avoid overfilling, or the engine could be damaged. ●...
  • Page 374 If the coolant level drops within a short time after replenishing Visually check the radiator, hoses, reservoir cap, radiator cap, drain cock and water pump. If you cannot find a leak, have your Toyota dealer pressure test the cap and check for leaks in the cooling system. ■...
  • Page 375 Radiator and condenser Check the radiator and condenser and clear any foreign objects. If either of the above parts are extremely dirty or you are not sure of their condition, have your vehicle checked by your Toyota dealer. CAUTION ■...
  • Page 376 4-3. Do-it-yourself maintenance Brake fluid ■ Checking fluid level The brake fluid level should be between the “MAX” and “MIN” lines on the tank. Make sure to check the fluid type and prepare the necessary items. ■ Adding fluid Fluid type FMVSS No.116 DOT 3 or SAE J1703 brake fluid Items Clean funnel...
  • Page 377 4-3. Do-it-yourself maintenance ■ Brake fluid can absorb moisture from the air Excess moisture in the fluid can cause a dangerous loss of braking effi- ciency. Use only newly opened brake fluid. CAUTION ■ When filling the reservoir Take care because brake fluid can harm your hands or eyes and damage painted surfaces.
  • Page 378 4-3. Do-it-yourself maintenance Battery ■ Battery exterior Make sure that the battery terminals are not corroded and that there are no loose connections, cracks, or loose clamps. Terminals Hold-down clamp VENZA_OM_OM73019U_(U)
  • Page 379 4-3. Do-it-yourself maintenance ■ Before recharging When recharging, the battery produces hydrogen gas which is flammable and explosive. Therefore, before recharging: ● If recharging with the battery installed on the vehicle, be sure to discon- nect the ground cable. ● Make sure the power switch on the charger is off when connecting and disconnecting the charger cables to the battery.
  • Page 380 4-3. Do-it-yourself maintenance CAUTION ■ Where to safely charge the battery Always charge the battery in an open area. Do not charge the battery in a garage or closed room where there is not sufficient ventilation. ■ How to recharge the battery Only perform a slow charge (5 A or less).
  • Page 381 4-3. Do-it-yourself maintenance Washer fluid If any washer does not work or the low windshield washer fluid level warning light comes on, the washer tank may be empty. Add washer fluid. CAUTION ■ When refilling the washer fluid Do not refill the washer fluid when the engine is hot or running, as the washer fluid contains alcohol and may catch fire if spilled on the engine etc.
  • Page 382: Tires

    ■ Tire rotation Rotate the tires in the order shown. To equalize tire wear and extend tire life, Toyota recom- mends that tire rotation is Front carried out at the same inter- val as tire inspection. VENZA_OM_OM73019U_(U)
  • Page 383 4-3. Do-it-yourself maintenance ■ The tire pressure warning system Your Toyota is equipped with a tire pressure warning system that uses tire pressure warning valves and transmitters to detect low tire inflation pressure before serious problems arise. (P. 441) The compact spare tire is not equipped with a tire pressure warning valve and transmitter.
  • Page 384 ● A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage If you are not sure, consult with your Toyota dealer. ■ Replacing tires and wheels If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly.
  • Page 385 4-3. Do-it-yourself maintenance ■ Tire types 1 Summer tires Summer tires are high-speed performance tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow-covered or icy roads.
  • Page 386 4-3. Do-it-yourself maintenance ■ Routine tire inflation pressure checks The tire pressure warning system does not replace routine tire inflation pressure checks. Make sure to check tire inflation pressure as part of your routine of daily vehicle checks. ■ Tire pressure warning system certification For vehicles sold in the U.S.A.
  • Page 387 Do not mix tires of different makes, models or tread patterns. Also, do not mix tires of remarkably different treadwear. ● Do not use tire sizes other than those recommended by Toyota. ● Do not mix differently constructed tires (radial, bias-belted, or bias-ply tires).
  • Page 388 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire (P.
  • Page 389: Tire Inflation Pressure

    4-3. Do-it-yourself maintenance Tire inflation pressure ■ Tire inflation pressure The recommended cold tire inflation pressure and tire size is dis- played on the tire and loading information label. (P. 496) VENZA_OM_OM73019U_(U)
  • Page 390 4-3. Do-it-yourself maintenance ■ Inspection and adjustment procedure Tire valve Tire pressure gauge STEP Remove the tire valve cap. STEP Press the tip of the tire pressure gauge onto the tire valve. STEP Read the pressure using the graduations of the gauge. STEP If the tire inflation pressure is not within the recommended levels, adjust tire pressure.
  • Page 391 Reduced driving comfort and tire life ● Reduced safety ● Damage to the drive train If a tire needs frequent refilling, have it checked by your Toyota dealer. ■ Instructions for checking tire inflation pressure When checking tire inflation pressure, observe the following: ●...
  • Page 392 4-3. Do-it-yourself maintenance CAUTION ■ Proper inflation is critical to save tire performance Keep your tires properly inflated. Otherwise, the following conditions may occur and result in an accident causing death or serious injury. ● Excessive wear ● Uneven wear ●...
  • Page 393: Wheels

    ● Bent wheels that have been straightened ■ Aluminum wheel precautions ● Use only Toyota wheel nuts and wrenches designed for use with your aluminum wheels. ● When rotating, repairing or changing your tires, check that the wheel nuts are still tight after driving 1000 miles (1600 km).
  • Page 394 4-3. Do-it-yourself maintenance ■ When replacing wheels The wheels of your Toyota are equipped with tire pressure warning valves and transmitters that allow the tire pressure warning system to provide advanced warning in the event of a loss in tire inflation pressure.
  • Page 395 Because tire repair or replacement may affect the tire pressure warn- ing valves and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your Toyota dealer.
  • Page 396: Air Conditioning Filter

    4-3. Do-it-yourself maintenance Air conditioning filter The air conditioning filter must be changed regularly to maintain air conditioning efficiency. ■ Removal method STEP Vehicles with smart key system: Turn the “ENGINE START STOP” switch off. Vehicles without smart key system: Turn the engine switch to the “LOCK”...
  • Page 397 4-3. Do-it-yourself maintenance Remove the filter cover. STEP Remove the air conditioning STEP filter and replace it with a new one. The “UP” marks shown on the filter should be pointing up. VENZA_OM_OM73019U_(U)
  • Page 398 4-3. Do-it-yourself maintenance ■ Checking interval Inspect and replace the air conditioning filter according to the maintenance schedule. In dusty areas or areas with heavy traffic flow early replacement may be required. (For scheduled maintenance information, refer to the “Scheduled Maintenance Guide”, “Owner’s Manual Supplement”.) ■...
  • Page 399: Key Battery

    4-3. Do-it-yourself maintenance Key battery Replace the battery with a new one if it is discharged. ■ You will need the following items: ● Flathead screwdriver (To prevent damage to the key, cover the tip of the screwdriver with rag.) ●...
  • Page 400 4-3. Do-it-yourself maintenance Remove the depleted battery. STEP Insert a new battery with the “+” terminal facing up. ■ Replacing the battery (vehicles without smart key system) Remove the cover. STEP Remove the module. STEP VENZA_OM_OM73019U_(U)
  • Page 401 Use a CR1632 (vehicles with smart key system), or CR2025 (vehicles without smart key system) lithium battery ● Batteries can be purchased at your Toyota dealer, jewelers, or camera stores. ● Replace only with the same or equivalent type recommended by a Toyota dealer.
  • Page 402 4-3. Do-it-yourself maintenance CAUTION ■ Removed battery and other parts These parts are small and if swallowed by a child they can cause choking. Keep away from children. Failure to do so could result in death or serious injury. NOTICE ■...
  • Page 403: Checking And Replacing Fuses

    4-3. Do-it-yourself maintenance Checking and replacing fuses If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. STEP Vehicles with smart key system: Turn the “ENGINE START STOP” switch off. Vehicles without smart key system: Turn the engine switch to the “LOCK”...
  • Page 404 Check if the fuse has blown. Type A Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid. ITY42C012 Type B Normal fuse Blown fuse Contact your Toyota dealer. VENZA_OM_OM73019U_(U)
  • Page 405 4-3. Do-it-yourself maintenance Fuse layout and amperage ratings ■ Engine compartment Fuse block ITI43V079a Back of the cover VENZA_OM_OM73019U_(U)
  • Page 406 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Outside rear view mirrors MIRROR 10 A (driving position memory) DEICER 20 A Windshield wiper de-icer Multiport fuel injection system/ INJ NO.1 15 A sequential multiport fuel injection system INJ NO.2 15 A Igniter system Multiport fuel injection system/ EFI NO.2 15 A...
  • Page 407 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Smart key system, multiport fuel injection system/sequential mul- EFI NO.1 10 A tiport fuel injection system, auto- matic transmission Multiport fuel injection system/ sequential multiport fuel injection ETCS 10 A system, electronic throttle con- trol system TURN-HAZ 15 A...
  • Page 408 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Gauges and meters, clock, audio system, main body ECU, wireless remote control, smart ECU-B 10 A key system, power back door, front passenger occupant clas- sification system RADIO-B 20 A Audio system, navigation system SPARE 7.5 A Spare fuse...
  • Page 409 4-3. Do-it-yourself maintenance ■ Driver’s side instrument panel Fuse Ampere Circuit RR DOOR 20 A Power windows RL DOOR 20 A Power windows FR DOOR 20 A Power windows FR FOG 15 A Fog lights 7.5 A On-board diagnosis system FL DOOR 20 A Power windows...
  • Page 410 4-3. Do-it-yourself maintenance Fuse Ampere Circuit SEAT HTR 20 A Seat heaters S/ROOF 25 A Electric moon roof Side marker lights, tail lights, TAIL 10 A license plate light Emergency flashers, audio sys- tem, clock, instrument panel light control, glove box light, console PANEL box light, steering switches, out- side rear view mirror defoggers,...
  • Page 411 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Navigation system, back-up lights, charging system, emer- GAUGE NO.1 10 A gency flashers, multi-informa- tion display FR WIPER 30 A Windshield wipers RR WIPER 15 A Rear window wiper Multiport fuel injection system/ sequential multiport fuel injection system, steering lock system, 10 A smart key system, SRS airbag...
  • Page 412 Never use a fuse of a higher amperage rating than indicated, or use any other object in place of a fuse. ● Always use a genuine Toyota fuse or equivalent. Never replace a fuse with a wire, even as a temporary fix. ●...
  • Page 413: Light Bulbs

    You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer.
  • Page 414 4-3. Do-it-yourself maintenance Vehicles with discharge headlights Front turn signal light Front side marker light Front fog light ■ Rear bulb locations Stop/tail and rear side Tail light marker lights Rear turn signal light Back-up light License plate light VENZA_OM_OM73019U_(U)
  • Page 415 4-3. Do-it-yourself maintenance Replacing light bulbs ■ Headlight low beams (vehicles with halogen headlights) Turn the bulb base counterclock- STEP wise. Unplug connector while STEP pushing the lock release. VENZA_OM_OM73019U_(U)
  • Page 416 4-3. Do-it-yourself maintenance Replace the light bulb, and install STEP the bulb base. Align the 3 tabs on the light bulb with the mounting, and insert. Turn and secure the bulb base. STEP Shake the bulb base gently to check that it is not loose, turn the headlights on once and visually confirm that no light is leaking through the mounting.
  • Page 417 4-3. Do-it-yourself maintenance ■ Headlight high beams and daytime running lights (vehicles with halogen headlights) Unplug connector while STEP pushing the lock release. Turn the bulb base counterclock- STEP wise. Replace the light bulb, and install STEP the light bulb. Align the 3 tabs on the light bulb with the mounting, and insert.
  • Page 418 4-3. Do-it-yourself maintenance Turn and secure the bulb base. STEP STEP Install the connector. Shake the bulb base gently to check that it is not loose, turn the headlights on once and visually confirm that no light is leaking through the mounting. VENZA_OM_OM73019U_(U)
  • Page 419 4-3. Do-it-yourself maintenance ■ Front fog lights Remove the engine under cover STEP bolt and pull down the engine under cover. Turn the bulb base counterclock- STEP wise. Unplug connector while STEP pushing the lock release. VENZA_OM_OM73019U_(U)
  • Page 420 4-3. Do-it-yourself maintenance Replace the light bulb, and install STEP the bulb base. Align the 3 tabs on the light bulb with the mounting, and insert. Turn and secure the bulb base. STEP Shake the bulb base gently to check that it is not loose, turn the front fog lights on once and visu- ally confirm that no light is leaking through the mounting.
  • Page 421 4-3. Do-it-yourself maintenance ■ Front turn signal lights (vehicles with discharge headlights) Turn the bulb base counterclock- STEP wise. Remove the light bulb. STEP VENZA_OM_OM73019U_(U)
  • Page 422 4-3. Do-it-yourself maintenance ■ Front side marker lights STEP Turn the bulb base counterclockwise. Vehicles with halogen headlights Vehicles with discharge headlights Remove the light bulb. STEP VENZA_OM_OM73019U_(U)
  • Page 423 4-3. Do-it-yourself maintenance ■ Rear turn signal lights, stop/tail and rear side marker lights Left side Open the back door and remove STEP the cover. To protect the cover, place a rag between the flathead screwdriver and cover as shown in the illus- trations.
  • Page 424 4-3. Do-it-yourself maintenance Remove the light bulb. STEP Stop/tail and rear side marker lights Rear turn signal light ■ Tail and back-up lights Open the back door and remove STEP the trim board. Turn the bulb base counterclock- STEP wise. Back-up light Tail light Remove the light bulb.
  • Page 425 4-3. Do-it-yourself maintenance ■ License plate light Open the back door and remove STEP the trim board. Turn the bulb base counterclock- STEP wise. Remove the light bulb. STEP VENZA_OM_OM73019U_(U)
  • Page 426 4-3. Do-it-yourself maintenance ■ Bulbs other than the above If any of the bulbs listed below has burnt out, have your Toyota dealer replace it. ● Headlight low and high beams (vehicles with discharge head- lights) ● Daytime running/parking lights (vehicles with discharge head- lights) ●...
  • Page 427 4-3. Do-it-yourself maintenance CAUTION ■ Replacing light bulbs ● Turn off the lights. Do not attempt to replace the bulb immediately after turning off the lights. The bulbs become very hot and may cause burns. ● Do not touch the glass portion of the light bulb with bare hands. When it is unavoidable to hold the glass portion, use and hold with a clean dry cloth to avoid getting moisture and oils on the bulb.
  • Page 428 4-3. Do-it-yourself maintenance CAUTION ■ Discharge headlights (if equipped) ● Contact your Toyota dealer before replacing the discharge headlights (including light bulbs). ● Do not touch the discharge headlight’s high voltage socket when the head- lights are turned on. An extremely high voltage of 30000 V will be discharged and could result in serious injury or death by electric shock.
  • Page 429: When Trouble Arises

    When trouble arises 5-1. Essential information 5-2. Steps to take in an emergency Emergency flashers ..430 If a warning light turns If your vehicle needs on or a warning buzzer to be towed ....431 sounds......438 If you think something If a warning message is is wrong ......
  • Page 430: Essential Information Emergency Flashers

    5-1. Essential information Emergency flashers The emergency flashers are used to warn other drivers when the vehicle has to be stopped in the road due to a breakdown, etc. Press the switch. All the turn signal lights will flash. To turn them off, press the switch once again.
  • Page 431: If Your Vehicle Needs To Be Towed

    If your vehicle needs to be towed If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or a commercial towing service, using a lift-type truck or a flat bed truck. Use a safety chain system for all towing, and abide by all state/pro- vincial and local laws.
  • Page 432 5-1. Essential information Towing with a sling-type truck Do not tow with a sling-type truck to prevent body damage. Towing with a wheel lift-type truck From the front (2WD models) Release the parking brake. From the front (AWD models) Use a towing dolly under the rear wheels.
  • Page 433 5-1. Essential information From the rear Use a towing dolly under the front wheels. Using a flat bed truck If you use chains or cables to tie down your vehicle, the angles shaded in black must be 45. Do not overly tighten the tie downs or the vehicle may be damaged.
  • Page 434 5-1. Essential information NOTICE ■ To prevent body damage when towing a sling-type truck Do not tow with a sling-type truck, either from the front or rear. ■ To prevent causing serious damage to the transmission and Active Torque Control 4WD system (AWD models) when towing using a wheel-lift type truck 2WD models: Never tow this vehicle from the rear with the front wheels on the...
  • Page 435: If You Think Something Is Wrong

    5-1. Essential information If you think something is wrong If you notice any of the following symptoms, your vehicle probably needs adjustment or repair. Contact your Toyota dealer as soon as possible. ■ Visible symptoms ● Fluid leaks under the vehicle (Water dripping from the air conditioning after use is normal.)
  • Page 436: If Noise Can Be Heard From Under Vehicle

    5-1. Essential information If noise can be heard from under vehicle Approximately five hours after the engine is turned off, you may hear sound coming from under the vehicle for several minutes. This is the sound of a fuel evaporation leakage check and, it does not indicate a malfunction.
  • Page 437: Fuel Pump Shut Off System

    5-1. Essential information Fuel pump shut off system To minimize the risk of fuel leakage when the engine stalls or an air- bag inflates upon collision, the fuel pump shut off system stops sup- plying fuel to the engine. Follow the procedure below to restart the engine after the system is activated.
  • Page 438: Steps To Take In An Emergency If A Warning Light Turns On Or A Warning Buzzer Sounds

    Stop the vehicle immediately. Continuing to drive the vehicle may be dangerous. The following warning indicates a possible problem in the brake sys- tem. Immediately stop the vehicle in a safe place and contact your Toyota dealer. Warning light Warning light/Details Brake system warning light (warning buzzer) •...
  • Page 439 Have the vehicle inspected immediately. Failing to investigate the cause of the following warnings may lead to the system operating abnormally and possibly cause an accident. Have the vehicle inspected by your Toyota dealer immediately. Warning light Warning light/Details Malfunction indicator lamp Malfunction in: •...
  • Page 440 5-2. Steps to take in an emergency Warning light Warning light/Details SRS warning light Malfunction in: • The SRS airbag system; • The front passenger occupant classification system; or • The seat belt pretensioner system. ABS warning light (U.S.A.) Malfunction in: •...
  • Page 441 • Flat tire (P. 453) is adjusted, have the system checked by your Toyota dealer. When the light comes on after blinking for 1 minute: Have the system checked Malfunction in the tire by your Toyota dealer. pressure warning system. (P. 449) VENZA_OM_OM73019U_(U)
  • Page 442 (Do not stop the drive has been automati- engine.) (AWD models) cally engaged. When the light comes on: Malfunction in the Active Have the system checked Torque Control 4WD sys- by your Toyota dealer. tem. VENZA_OM_OM73019U_(U)
  • Page 443 5-2. Steps to take in an emergency Warning light Warning light/Details Correction procedure Maintenance required reminder light Indicates that mainte- nance is requires accord- ing to the driven distance on the maintenance schedule. Illuminates for about 3 sec- onds and then flashes for about 15 seconds approxi- If necessary, perform main- mately 4500 miles...
  • Page 444 5-2. Steps to take in an emergency Follow the correction procedures. (smart key system) After taking the specified steps to correct the suspected problem, check that the warning light turns off. Interior Exterior Warning Correction Warning light/Details buzzer buzzer light procedure Smart key system warning light...
  • Page 445 5-2. Steps to take in an emergency Interior Exterior Warning Correction Warning light/Details buzzer buzzer light procedure Smart key system warning light Indicates that the Turn the driver’s door has “ENGINE been opened or START closed with the shift STOP” lever in “P”, the switch off Once...
  • Page 446 The malfunction indicator lamp will go off after taking several driving trips. If the malfunction indicator lamp does not go off even after several trips, con- tact your Toyota dealer as soon as possible. ■ Key reminder buzzer (vehicles without smart key system) The buzzer indicates that the key has not been removed with the engine off and the driver’s door opened.
  • Page 447 5-2. Steps to take in an emergency ■ SRS warning light This warning light system monitors the airbag sensor assembly, front airbag sensors, side and curtain shield airbag sensors, curtain shield airbag sen- sors, driver’s seat position sensor, driver’s seat belt buckle switch, front pas- senger occupant classification system (ECU and sensors), “AIR BAG ON”...
  • Page 448 If there is a lot of snow or ice on the vehicle, in particular around the wheels or wheel housings. ● If non-genuine Toyota wheels are used. (Even if you use Toyota wheels, the tire pressure warning system may not work properly with some types of tires.) ●...
  • Page 449 If the tire pressure warning light frequently comes on after blinking for 1 minute when the “ENGINE START STOP” switch is turned to IGNI- TION ON mode, have it checked by your Toyota dealer. Vehicles without smart key system If the tire pressure warning light comes on after blinking 1 minute fre- quently when the engine switch is turned to the “ON”...
  • Page 450 5-2. Steps to take in an emergency CAUTION ■ If a blowout or sudden air loss should occur The tire pressure warning system may not activate immediately. ■ Maintenance of the tires Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label (tire and load information label).
  • Page 451 5-2. Steps to take in an emergency CAUTION Your vehicle has also been equipped with a TPMS (tire pressure warning system) malfunction indicator to indicate when the system is not operat- ing properly. The TPMS (tire pressure warning system) malfunction indi- cator is combined with the low tire pressure telltale (tire pressure warning light).
  • Page 452: If A Warning Message Is Displayed

    A buzzer may sound when a warning message is shown on the multi-information display. ■ If the warning message is shown again after its correction procedure has been performed Contact your Toyota dealer as soon as possible.  : If equipped VENZA_OM_OM73019U_(U)
  • Page 453: If You Have A Flat Tire

    5-2. Steps to take in an emergency If you have a flat tire Remove the flat tire and replace it with the spare provided. ■ Before jacking up the vehicle ● Stop the vehicle on a hard, flat surface. ● Set the parking brake. ●...
  • Page 454 5-2. Steps to take in an emergency ■ Compact spare tire The compact spare tire saves space in your luggage compart- ment, and its lighter weight helps to enhance fuel economy and permits easier installation in case of a flat tire. The compact spare tire is designed for temporary emer- gency use only.
  • Page 455 5-2. Steps to take in an emergency Taking out the spare tire Loosen the center fastener that secures the spare tire. Replacing a flat tire Chock the tires. STEP Flat tire Wheel chock positions Left-hand side Behind the rear right-hand side tire Front Right-hand side Behind the rear left-hand side tire...
  • Page 456 5-2. Steps to take in an emergency Slightly loosen the wheel nuts STEP (one turn). Turn the tire jack portion “A” by STEP hand until the notch of the jack is in contact with the jack point. Raise the vehicle until the tire is STEP slightly raised off the ground.
  • Page 457 5-2. Steps to take in an emergency Remove all the wheel nuts and STEP the tire. When resting the tire on the ground, place the tire so that the wheel design faces up to avoid scratching the wheel surface. Installing the spare tire Remove any dirt or foreign mat- STEP ter from the wheel contact sur-...
  • Page 458 5-2. Steps to take in an emergency Lower the vehicle. STEP Firmly tighten each nut two or STEP three times in the order shown in the illustration. Tightening torque: 76 ft•lbf (103 N•m, 10.5 kgf•m) STEP Stow the flat tire, tire jack and all tools. VENZA_OM_OM73019U_(U)
  • Page 459 5-2. Steps to take in an emergency ■ The compact spare tire ● The compact spare tire is identified by the label “TEMPORARY USE ONLY” on the tire sidewall. Use the compact spare tire temporarily only in an emergency. ● Make sure to check the tire inflation pressure of the compact spare tire.
  • Page 460 5-2. Steps to take in an emergency CAUTION ■ Using the tire jack Improper use of the tire jack may lead to death or serious injuries due to the vehicle suddenly falling off the jack. ● Do not use the tire jack for any purpose other than replacing tires or installing and removing tire chains.
  • Page 461 5-2. Steps to take in an emergency CAUTION ■ Replacing a flat tire ● Do not touch the disc wheels or the area around the brakes immedi- ately after the vehicle has been driven. After the vehicle has been driven the disc wheels and the area around the brakes will be extremely hot.
  • Page 462 5-2. Steps to take in an emergency CAUTION ■ When using the compact spare tire ● Remember that your compact spare tire is specifically designed for use with your vehicle. Do not use your compact spare tire on another vehicle. ●...
  • Page 463 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire (P.
  • Page 464: If The Engine Will Not Start

    5-2. Steps to take in an emergency If the engine will not start If the engine still does not start after following the correct starting procedure (P. 171, 175) or releasing the steering lock (P. 173, 176), confirm the following points. ■...
  • Page 465 ● The battery may be discharged. (P. 472) ● There may be a malfunction in the steering lock system (vehi- cles with smart key system). Contact your Toyota dealer if the problem cannot be repaired, or if repair procedures are unknown. VENZA_OM_OM73019U_(U)
  • Page 466 Press and hold the “ENGINE START STOP” switch for about 15 seconds while depressing the brake pedal firmly. Even if the engine can be started using the above steps, the system may be malfunctioning. Have the vehicle checked by your Toyota dealer. VENZA_OM_OM73019U_(U)
  • Page 467: If The Shift Lever Cannot Be Shifted From "P

    (a system to prevent accidental operation of the shift lever). Have the vehicle inspected by your Toyota dealer immediately. The following steps may be used as an emergency measure to ensure that the shift lever can be shifted.
  • Page 468: If You Lose Your Keys

    5-2. Steps to take in an emergency If you lose your keys New genuine keys can be made by your Toyota dealer. Bring the other key and the key number stamped on the key number plate. VENZA_OM_OM73019U_(U)
  • Page 469: If The Electronic Key Does Not Operate Properly (Vehicles With Smart Key System)

    5-2. Steps to take in an emergency If the electronic key does not operate properly (vehicles with smart key system) If communication between the electronic key and vehicle is inter- rupted (P. 30) or the electronic key cannot be used because the battery is depleted, the smart key system and wireless remote con- trol cannot be used.
  • Page 470 5-2. Steps to take in an emergency Starting the engine STEP Shift the shift lever to “P” and apply the brakes. Touch the Toyota emblem side of STEP electronic “ENGINE START STOP” switch. An alarm will sound to indicate that the start function cannot detect the electronic key that is touched to the “ENGINE START...
  • Page 471 5-2. Steps to take in an emergency ■ Stopping the engine Shift the shift lever to “P” and press the “ENGINE START STOP” switch as you normally do when stopping the engine. ■ Replacing the key battery As this above procedure is a temporary measure, it is recommended that the electronic key battery be replaced immediately when the battery depletes.
  • Page 472: If The Battery Is Discharged

    You can call your Toyota dealer or qualified repair shop. If you have a set of jumper (or booster) cables and a second vehi- cle with a 12 volt battery, you can jump start your Toyota following the steps below.
  • Page 473 5-2. Steps to take in an emergency 1AR-FE engine Positive (+) battery terminal on your vehicle Positive (+) battery terminal on the second vehicle Negative (-) battery terminal on the second vehicle Connect the jumper cable to ground on your vehicles as shown in the illustration.
  • Page 474 Once the vehicle’s engine has started, remove the jumper cables in the exact reverse order in which they were con- nected. Once the engine starts, have the vehicle checked at your Toyota dealer as soon as possible. ■ Starting the engine when the battery is discharged The engine cannot be started by push-starting.
  • Page 475 5-2. Steps to take in an emergency ■ Charging the battery The electricity stored in the battery will discharge gradually even when the vehicle is not in use, due to natural discharge and the draining effects of cer- tain electrical appliances. If the vehicle is left for a long time, the battery may discharge, and the engine may be unable to start.
  • Page 476 5-2. Steps to take in an emergency CAUTION ■ Battery precautions The battery contains poisonous and corrosive acidic electrolyte, while related parts contain lead and lead compounds. Observe the following pre- cautions when handling the battery: ● When working with the battery, always wear safety glasses and take care not to allow any battery fluids (acid) to come into contact with skin, clothing or the vehicle body.
  • Page 477: If Your Vehicle Overheats

    (radia- tor) for any leaks. Radiator Cooling fans If a large amount of coolant leaks, immediately contact your Toyota dealer. The coolant level is satisfactory if STEP it is between the “F” and “L” lines on the reservoir.
  • Page 478 (The fans may not operate in freezing temperatures.) STEP If the fans are not operating: Stop the engine immediately and contact your Toyota dealer. If the fans are operating: Have the vehicle inspected at the nearest Toyota dealer. VENZA_OM_OM73019U_(U)
  • Page 479 5-2. Steps to take in an emergency CAUTION ■ To prevent an accident or injury when inspecting under the hood of your vehicle ● If steam is seen coming from under the hood, do not open the hood until the steam has subsided. The engine compartment may be very hot, caus- ing serious injury such as burns.
  • Page 480: If The Vehicle Becomes Stuck

    5-2. Steps to take in an emergency If the vehicle becomes stuck Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt, or snow. STEP Stop the engine. Set the parking brake and shift the shift lever in “P”.
  • Page 481 5-2. Steps to take in an emergency CAUTION ■ When attempting to free a stuck vehicle If you choose to rock the vehicle back and forth to free it, make sure the sur- rounding area is clear, to avoid striking other vehicles, objects or persons. The vehicle may also lunge forward or lunge back suddenly as it becomes free.
  • Page 482: If Your Vehicle Has To Be Stopped In An Emergency

    5-2. Steps to take in an emergency If your vehicle has to be stopped in an emergency Only in an emergency, such as if it becomes impossible to stop the vehicle in the normal way, stop the vehicle using the following pro- cedure: STEP Steadily step on the brake pedal with both feet and firmly...
  • Page 483 5-2. Steps to take in an emergency Vehicles with a smart key sys- STEP tem: To stop the engine, press and hold the “ENGINE START STOP” switch for 2 consecu- tive seconds or more, or press Press and hold for 2 seconds or more, it briefly 3 times or more in or press briefly 3 times or more succession.
  • Page 484 5-2. Steps to take in an emergency VENZA_OM_OM73019U_(U)
  • Page 485: Vehicle Specifications

    Vehicle specifications 6-1. Specifications Maintenance data (fuel, oil level, etc.) ..486 Fuel information ....500 Tire information ....504 6-2. Customization Customizable features ......519 6-3. Initialization Items to initialize ....529 VENZA_OM_OM73019U_(U)
  • Page 486: Maintenance Data (Fuel, Oil Level, Etc.)

    6-1. Specifications Maintenance data (fuel, oil level, etc.) Dimensions and weights Overall length 189.0 in. (4800 mm) Overall width 75.0 in. (1905 mm) Overall height 63.4 in. (1610 mm) Wheelbase 109.3 in. (2775 mm) Front 64.2 in. (1630 mm) Tread 64.4 in.
  • Page 487 Vehicle identification number The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle. This number is stamped on the top left of the instrument panel.
  • Page 488 6-1. Specifications ■ Engine number 2GR-FE engine The engine number is stamped on the engine block as shown. 1AR-FE engine VENZA_OM_OM73019U_(U)
  • Page 489 6-1. Specifications Engine Model 2GR-FE, 1AR-FE Type 2GR-FE engine 6-cylinder V type, 4-cycle, gasoline 1AR-FE engine 4-cylinder in line, 4-cycle, gasoline Bore and stroke 3.70  3.27 in. (94.0  83.0 mm) 2GR-FE engine 3.54  4.13 in. (90.0  105.0 mm) 1AR-FE engine Displacement 2GR-FE engine...
  • Page 490 ■ Engine oil selection “Toyota Genuine Motor Oil” is used in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the following grade and viscosity. Oil grade: ILSAC GF-5 multigrade engine oil...
  • Page 491 6-1. Specifications Recommended viscosity: SAE 0W-20 SAE 0W-20 is the best choice for good fuel economy and good starting in cold weather. If SAE 0W-20 is not available, SAE 5W-20 oil may be used. However, it must be replaced Outside temperature with SAE 0W-20 at the next oil change.
  • Page 492 (10.1 L, 8.9 Imp.qt.) 1AR-FE engine 7.5 qt. (7.1 L, 6.2 Imp.qt.) Use either of the following: • “Toyota Super Long Life Coolant” • Similar high-quality ethylene glycol-based non- Coolant type silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technol- Do not use plain water alone.
  • Page 493 6-1. Specifications Ignition system Spark plug Make DENSO 2GR-FE engine FK20HR11 1AR-FE engine SK16HR11 0.043 in. (1.1 mm) NOTICE ■ Iridium-tipped spark plugs Use only iridium-tipped spark plugs. Do not adjust gap when tuning engine. Electrical system Battery 12.6  12.8 V Fully charged Open voltage at 12.2 ...
  • Page 494 NOTICE ■ Automatic transaxle fluid type Using transaxle fluid other than “Toyota Genuine ATF WS” may cause dete- rioration in shift quality, locking up of your transaxle accompanied by vibra- tion, and ultimately damage the transaxle of your vehicle. Transfer (AWD models) Oil capacity 0.84 qt.
  • Page 495 6-1. Specifications Brakes Pedal clearance 1.1 in. (28 mm) Min.  0.12 in. (1.0  3.0 mm) Pedal free play 0.04 Brake pad wear limit 0.04 in. (1.0 mm) Parking brake lining wear limit 0.04 in. (1.0 mm)  6 clicks Parking brake adjustment Fluid type SAE J1703 or FMVSS No.
  • Page 496 6-1. Specifications Tires and wheels Type A Tire size P245/50R20 102H Driving under normal conditions Front tires: 32 psi (220 kPa, 2.2 kgf/cm or bar) Rear tires: 32 psi (220 kPa, 2.2 kgf/cm or bar) Tire inflation pressure Driving at high speeds above 99 mph (Recommended cold tire (160 km/h) (in countries where such inflation pressure)
  • Page 497 6-1. Specifications Type B Tire size P245/55R19 103S Driving under normal conditions Front tires: 32 psi (220 kPa, 2.2 kgf/cm or bar) Rear tires: 32 psi (220 kPa, 2.2 kgf/cm or bar) Tire inflation pressure Driving at high speeds above 99 mph (Recommended cold tire (160 km/h) (in countries where such inflation pressure)
  • Page 498 6-1. Specifications Light bulbs Bulb Light Bulbs Type Headlights Vehicles with discharge headlights  Low and high beam Vehicles with halogen headlights  Low beam High beam 9005 Front turn signal lights 7444 (vehicles with discharge headlights) Front turn signal/parking lights 3457 30/8 (vehicles with halogen headlights)
  • Page 499 6-1. Specifications Bulb Light Bulbs Type  Front interior light  Front personal lights  Rear personal/interior lights  Interior Vanity lights  Door courtesy lights Glove box light  Luggage compartment light A: D4S discharge bulbs D: Wedge base bulbs (amber) B: H11 halogen bulbs E: Wedge base bulbs (clear) C: HB3 halogen bulbs...
  • Page 500: Fuel Information

    ASTM D4814 in the U.S.A. and CGSB3.5-M93 in Canada. ■ Fuel tank opening for unleaded gasoline To help prevent incorrect fueling, your Toyota has a fuel tank opening that only accommodates the special nozzle on unleaded fuel pumps. ■...
  • Page 501 EPA’s lowest additives con- centration program. ● Toyota strongly recommends the use of Top Tier Detergent Gasoline. For more information on Top Tier Detergent Gasoline and a list of marketers, please go to the official website www.toptiergas.com.
  • Page 502 15% ethanol). (85% ethanol) ● If you use gasohol in your Toyota, be sure that it has an octane rating no lower than 87. ● Toyota DOES NOT recommend the use of gasoline containing methanol.
  • Page 503 6-1. Specifications NOTICE ■ Notice on fuel quality ● Do not use improper fuels. If improper fuels are used the engine will be damaged. ● Do not use leaded gasoline. Leaded gasoline can cause damage to your vehicle’s three-way catalytic converters causing the emission control system to malfunction.
  • Page 504: Tire Information

    6-1. Specifications Tire information Typical tire symbols Standard tire Compact spare tire Tire size (P. 507) DOT and Tire Identification Number (TIN) (P. 506) VENZA_OM_OM73019U_(U)
  • Page 505 6-1. Specifications Location of treadwear indicators (P. 382) Tire ply composition and materials Plies are layers of rubber-coated parallel cords. Cords are the strands which form the plies in a tire. Summer tire or all season tire (P. 385) An all season tire has “M+S” on the sidewall. A tire not marked “M+S”...
  • Page 506 6-1. Specifications Typical DOT and tire identification number (TIN) DOT symbol Tire Identification Number (TIN) Tire manufacturer’s identifica- tion mark Tire size code Manufacturer’s optional tire type code (3 or 4 letters) Manufacturing week Manufacturing year : The DOT symbol certifies that the tire conforms to applicable Federal...
  • Page 507 6-1. Specifications Tire size ■ Typical tire size information The illustration indicates typical tire size. Tire use (P = Passenger car, T = Temporary use) Section width (millimeters) Aspect ratio (tire height to section width) Tire construction code (R = Radial, D = Diagonal) Wheel diameter (inches) Load index (2 or 3 digits) Speed symbol...
  • Page 508 6-1. Specifications ■ Tire dimensions Section width Tire height Wheel diameter Tire section names Bead Sidewall Shoulder Tread Belt Inner liner Reinforcing rubber ITY61C013 Carcass Rim lines Bead wires Chafer VENZA_OM_OM73019U_(U)
  • Page 509 U.S. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading. Your Toyota dealer will help answer any questions you may have as you read this information. ■ DOT quality grades All passenger vehicle tires must conform to Federal Safety Requirements in addition to these grades.
  • Page 510 6-1. Specifications ■ Traction AA, A, B, C The traction grades, from highest to lowest, are AA, A, B and C, and they represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete.
  • Page 511 6-1. Specifications Glossary of tire terminology Tire related term Meaning Tire pressure when the vehicle has been Cold tire inflation parked for three hours or more, or has not pressure been driven more than 1 mile or 1.5 km under that condition The maximum cold inflated pressure to which a Maximum inflation...
  • Page 512 6-1. Specifications Tire related term Meaning 150 lb. (68 kg) times the number of occupants Normal occupant specified in the second column of Table 1 that weight follows Distribution of occupants in a vehicle as speci- Occupant distribution fied in the third column of Table 1 below The combined weight of installed regular pro- duction options weighing over 5 lb.
  • Page 513 6-1. Specifications Tire related term Meaning The load on an individual tire that is determined Vehicle maximum load by distributing to each axle its share of the on the tire maximum loaded vehicle weight, and dividing by two The load on an individual tire that is determined by distributing to each axle its share of curb Vehicle normal load weight, accessory weight, and normal occu-...
  • Page 514 6-1. Specifications Tire related term Meaning Cord The strands forming the plies in the tire The parting of cords from adjacent rubber com- Cord separation pounds Any parting within the tread, sidewall, or inner- Cracking liner of the tire extending to cord material A pneumatic tire with an inverted flange tire and rim system in which the rim is designed with rim flanges pointed radially inward and the...
  • Page 515 6-1. Specifications Tire related term Meaning (a)The sidewall that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or Intended outboard deeper than the same molding on the other sidewall sidewall of the tire, or (b)The outward facing sidewall of asymmetrical tire that has a particular side that must always face outward when mounted on a vehicle...
  • Page 516 6-1. Specifications Tire related term Meaning A tire intended for use on passenger cars, mul- tipurpose passenger vehicles, and trucks, that Passenger car tire have a gross vehicle weight rating (GVWR) of 10,000 lb. or less A layer of rubber-coated parallel cords A parting of rubber compound between adja- Ply separation cent plies...
  • Page 517 6-1. Specifications Tire related term Meaning A tire that attains a traction index equal to or greater than 110, compared to the ASTM E- 1136 Standard Reference Test Tire, when using the snow traction test as described in ASTM F-1805-00, Standard Test Method for Snow tire Single Wheel Driving Traction in a Straight Line on Snow-and Ice-Covered Surfaces, and which...
  • Page 518 6-1. Specifications : Table 1  Occupant loading and distribution for vehicle normal load for various designated seating capacities Designated seating Occupant distribution in Vehicle normal load, capacity, Number of a normally loaded Number of occupants occupants vehicle 2 through 4 2 in front 2 in front, 1 in second 5 through 10...
  • Page 519: Customization Customizable Features

    Toyota dealer. Some function settings are changed simultaneously with other functions being customized. Contact your Toyota dealer for further details. Customizable features Vehicles with TFT type multi-information display: Some function settings can be changed by operating the multi-information display.
  • Page 520 6-2. Customization Default Customized Item Function setting setting Smart key system — O Smart key system Select doors to Driver’s All doors — O (P. 30) unlock door Wireless remote — O control Driver’s door unlocked in All doors Unlocking operation one step, unlocked in Wireless...
  • Page 521 6-2. Customization Default Customized Item Function setting setting Operation signal (Emergency flashers) Level 1 to 6 Operation signal Level 7 — O Smart key (Buzzer) system (P. 30) and wireless Time elapsed before remote control automatic door lock (P. 45) function is activated 60 seconds 30 seconds...
  • Page 522 6-2. Customization Default Customized Item Function setting setting Driver’s door unlocked in All doors Unlocking using one step, all unlocked in — O a key doors one step unlocked in two step Speed-detecting automatic door lock function Door lock (P. 50) Shifting the shift lever to position other than “P”...
  • Page 523 6-2. Customization Default Customized Item Function setting setting Light sensor Level 3 Level 1 to 5 — O sensitivity Daytime running light — O system (U.S.A. only) Automatic High Beam Automatic light (if equipped) control system (P. 208) 0 seconds Time elapsed before headlights automatically turn off...
  • Page 524 6-2. Customization Default Customized Item Function setting setting 7.5 seconds Time period before 15 seconds lights turn off 30 seconds Vehicles with smart key system: Operation after the “ENGINE START STOP” switch is turned off — O Vehicles without smart key system: Operation after the engine switch is Illumination...
  • Page 525 6-2. Customization Default Customized Item Function setting setting Seat belt Vehicle speed linked reminder seat belt reminder — O (P. 441) buzzer Rear window Auto Power — O Up/Down window (P. 96) Auto Up function — O VENZA_OM_OM73019U_(U)
  • Page 526 6-2. Customization Customizing the features by using the multi-information display (vehicles with TFT type multi-information display) Press the “SETUP” button while STEP the vehicle is stopped. The “Custom Settings” screen is displayed on the multi-information display. If left idle for approximately 10 seconds, the display will revert to the previous screen.
  • Page 527 6-2. Customization Select the setting you wish to STEP change by pressing the “INFO” or “SETUP” button, and press the “SELECT RESET” button. The illustration assumes that STEP “Door” was chosen in The current setting is indicated by yellow text. If you select “Return”...
  • Page 528 6-2. Customization ■ Restoring default settings Press the “SETUP” button while STEP the vehicle is stopped. The “Custom Settings” screen is displayed on the multi-information display. If left idle for approximately 10 seconds, the display will revert to the previous screen. Select “Default Settings”...
  • Page 529: Initialization Items To Initialize

    6-3. Initialization Items to initialize The following items must be initialized for normal system operation in cases such as after the battery is reconnected, or maintenance is performed on the vehicle. Item When to initialize Reference • After reconnecting or changing the Power back door battery P.
  • Page 530 6-3. Initialization VENZA_OM_OM73019U_(U)
  • Page 531: For Owners

    For owners Reporting safety defects for U.S. owners ....532 Seat belt instructions for Canadian owners (in French) ..... 533 SRS airbag instructions for Canadian owners (in French) ..... 535 VENZA_OM_OM73019U_(U)
  • Page 532: Reporting Safety Defects For U.s. Owners

    If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800-331-4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
  • Page 533: Seat Belt Instructions For Canadian Owners (In French)

    Seat belt instructions for Canadian owners (in French) The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions in English. VENZA_OM_OM73019U_(U)
  • Page 534 VENZA_OM_OM73019U_(U)
  • Page 535: Srs Airbag Instructions For Canadian Owners (In French)

    SRS airbag instructions for Canadian owners (in French) VENZA_OM_OM73019U_(U)
  • Page 536 VENZA_OM_OM73019U_(U)
  • Page 537 VENZA_OM_OM73019U_(U)
  • Page 538 VENZA_OM_OM73019U_(U)
  • Page 539 VENZA_OM_OM73019U_(U)
  • Page 540 VENZA_OM_OM73019U_(U)
  • Page 541 VENZA_OM_OM73019U_(U)
  • Page 542 VENZA_OM_OM73019U_(U)
  • Page 543 VENZA_OM_OM73019U_(U)
  • Page 544 VENZA_OM_OM73019U_(U)
  • Page 545 VENZA_OM_OM73019U_(U)
  • Page 546 VENZA_OM_OM73019U_(U)
  • Page 547: Index

    Index Abbreviation list ..... 548 Alphabetical index....550 What to do if......559 For information regarding the equipment listed below, refer to the “Navigation System Owner’s Manual” or “Display Audio System Owner’s Manual”. • Navigation system • Audio system •...
  • Page 548: Abbreviation List

    Abbreviation list Abbreviation/Acronym list ABBREVIATIONS MEANING 2-Wheel Drive 4-Wheel Drive Anti-lock Brake System Accessory Automatic Locking Retractor Auxiliary All-Wheel Drive Air Conditioning Child Restraint System ECON Economy Electronic Control Unit Event Data Recorder Emergency Locking Retractor Electric Power Steering GAWR Gross Axle Weight Rating GCWR Gross Combination Weight Rating...
  • Page 549 Abbreviation list ABBREVIATIONS MEANING On Board Diagnostics PASS Passenger Power Power Steering Supplemental Restraint System TEMP Temperature Thin Film Transistor Tire Identification Number TPMS Tire Pressure Warning System TRAC Traction Control Vehicle Identification Number Vehicle Stability Control VENZA_OM_OM73019U_(U)
  • Page 550: Alphabetical Index

    Alphabetical index Alphabetical index Automatic air conditioning Air conditioning filter....396 system ........286 Automatic air conditioning Automatic headlight leveling system ........286 system ........211 ABS ...........238 Automatic High Beam ..... 212 Active head restraint ....68 Automatic light control Active Torque Control 4WD system ........
  • Page 551 Alphabetical index Care Child safety Exterior ......... 346 Airbag precautions ....127 Interior ........349 Back door precautions ....61 Seat belts ......350 Battery precautions ..380, 402 Cargo capacity ......251 Child-protectors.......52 Cargo hooks ......330 Child restraint system....139 CD player How your child should wear Chains ........
  • Page 552 Alphabetical index Daytime running light Emergency, in case of system ........210 If a warning message is Defogger displayed ......452 Rear window ......296 If the electronic key does Dimension.........486 not operate properly ... 469 Dinghy towing ......284 If the engine will not start ..464 Display If the shift lever cannot be Shift position and shift...
  • Page 553 Alphabetical index Engine coolant temperature Fuel gauge ........186 Capacity ........489 Engine immobilizer system..108 Fuel gauge ......186 Engine oil Fuel pump shut off system ..437 Capacity ....... 490 Information ......500 Checking ......369 Refueling .......104 Preparing and checking Type ........500 before winter ......
  • Page 554 Alphabetical index I/M test........358 Language Identification Multi-information Engine ........488 display ......192, 519 Vehicle ........487 Licence plate lights Ignition Replacing light bulbs..... 425 Engine switch ....171, 175 Wattage......... 498 Keys ........28 Light bulbs Ignition switch....171, 175 Replacing ......413 Ignition switch....171, 175 Wattage.........
  • Page 555 Alphabetical index Maintenance Parking brake ......184 Do-it-yourself maintenance .. 359 Parking lights General maintenance ... 355 Replacing light bulbs .....420 Maintenance data....486 Switch........208 Maintenance requirements... 352 Wattage.........498 Reset the maintenance Personal lights data ........353 Switch........307 Meter Wattage.........498 Instrument panel light Power back door ......56 control ........
  • Page 556 Alphabetical index Seat belts Shift lock system ..... 467 Adjusting the seat belt.....82 Shopping bag hooks ....330 Automatic Locking Side airbags ......118 Retractor .......83 Side marker lights Child restraint system Replacing light bulbs..422, 423 installation......145 Switch ........208 Cleaning and maintaining Wattage.........
  • Page 557 Alphabetical index Switch Tires Driving position memory Chains ........260 switches ....... 73 Checking .......382 Emergency flasher switch ..430 If you have a flat tire....453 Engine switch ....171, 175 Inflation pressure....389 Fog light switch..... 219 Information ......504 Ignition switch....171, 175 Pressure warning system..383 Intuitive parking assist Replacing ......453...
  • Page 558 Alphabetical index Vanity lights Warning messages ....452 Vanity lights......321 Washer Wattage.........498 Checking ....... 381 Vanity mirrors......321 Preparing and checking Vehicle identification before winter....... 258 number ........487 Switch ......221, 225 Vehicle stability control...238 Washing and waxing ....346 VSC..........238 Weight Cargo capacity ......
  • Page 559: What To Do If

    What to do if... What to do if... A tire punctures If you have a flat tire P. 453 P. 108 Engine immobilizer system The engine does not start P. 464 If the engine will not start P. 472 If the battery is discharged The shift lever cannot be If the shift lever cannot be shifted P.
  • Page 560 What to do if... The warning light or indicator If the warning light turns on or a P. 438 light comes on warning buzzer sounds... Instrument cluster Center display VENZA_OM_OM73019U_(U)
  • Page 561 What to do if... ■ Warning lights Master warning light Open door warning light P. 442 P. 441 Low engine oil pressure Tire pressure warning warning light P. 439 light P. 441 Charging system Maintenance required warning light reminder light P.
  • Page 562 What to do if... VENZA_OM_OM73019U_(U)
  • Page 563 What to do if... VENZA_OM_OM73019U_(U)
  • Page 564: Gas Station Information

    6.4 (6.1, 5.4) 4.6 (4.4, 3.9) reference) Without filter 6.0 (5.7, 5.0) 4.2 (4.0, 3.5) “Toyota Genuine Motor Oil” or equivalent Oil grade P. 490 2GR-FE engine: ILSAC multigrade engine oil Engine oil type 1AR-FE engine: ILSAC GF-5 multigrade engine oil...

Table of Contents