Table of Contents
Advertisement
Operating and Installation Instructions
Inbuilt Royale (Australia)
Timberflame IB35R (New Zealand)
IMPORTANT
This appliance shall be installed in accordance with:
Manufacturers Installation Instructions.
•
Local Gas fitting regulations.
•
Municipal Building codes.
•
AGA Gas Installation Code AG601 - NZ 5261.
•
Any other relevant statutory regulation.
•
Rinnai strongly recommend that this product be installed with an
•
approved flue system for optimum product performance.
This appliance must only be installed, serviced and removed by an
•
authorised person.
For Australian installation, this appliance must be installed with
•
the supplied wire dressguard.
This heater is NOT designed to be built directly into any combustible
opening.
For combustible opening installations, a Rinnai Zero Clearance Kit is
available from your Gas Appliance Retailer.
Flame Fire
Table of Contents
Customer Instructions
Safety Points
Installation Instructions
2
3
4
5
6
8
9
10
11
11
12
12
Advertisement
Table of Contents
Related Manuals for Rinnai IB35R
Summary of Contents for Rinnai IB35R
-
Page 1: Table Of Contents
AGA Gas Installation Code AG601 - NZ 5261. • Any other relevant statutory regulation. • Rinnai strongly recommend that this product be installed with an • approved flue system for optimum product performance. This appliance must only be installed, serviced and removed by an •... -
Page 2: Location
5. Under no circumstances must combustible materials be present on the inside of the fireplace recess or flueway. Note: A Rinnai Zero Clearance kit is available where the heater is required to be installed in close proximity to combustible framing. -
Page 3: Flueing
There must be no leakage of smoke through the structure of the chimney during or after the test. Inside, upstairs and/or adjacent rooms should also be checked. If any of the above criteria is not met, a Rinnai approved flue liner system must be installed. -
Page 4: Chimney Inspection
FLUEING CHECK DIMENSIONS OF FIREPLACE • Check dimensions of fireplace and if necessary bring them to dimensions shown. Note: Brackets are supplied to retain the heater to the fireplace and must be attached prior to installation as shown in the diagram. CHECK FLUEWAY •... -
Page 5: Gas Connection
GAS CONNECTION RUN GAS SUPPLY • For pipe sizing, refer to your local gas installation codes. Copper supply should be run leaving the end of the pipe in a suitable position to be able to attach to the stainless steel flexi- tube and the 1/2”... -
Page 6: Log Installation
LOG INSTALLATION he logset is packed inside the heater and the packaging must be removed prior to installing the logset in its correct position. • Open both side panels. • Remove fastenings on both sides of the top glass retainer. Lift retainer away from heater. -
Page 7: Testing & Commissioning
INSTRUCT CUSTOMER ON USE OF UNIT • Explain to customer about use and care of unit. Make sure the customer understands the instructions. EXPLAIN • Ignition, Adjusting heat level, Fan Switch, Turning “OFF”. NOTE: RINNAI RESERVES THE RIGHT TO CHANGE OR MODIFY SPECIFICATIONS WITHOUT NOTICE. -
Page 8: Technical Data
FGL30 IDBN (NG) Australia FGL30 IDBL (Propane) Australia IB35RN (NG) New Zealand IB35RL (Propane) New Zealand Description: Rinnai Inbuilt Radiant/Convector, glass-fronted, ceramic log space heater with forced convection and natural draught flue system. Input: 33 MJ/h Natural Gas and Propane. Gas Control: Rinnai Push-Button Combination Control. -
Page 9: Installation Checklist
INSTALLATION / COMMISSIONING CHECKLIST (To be completed by certified Gas Installer) ____________________ Model: 1. Was a fireplace inspection carried out? (ie. clearances, combustibles etc.) 2. Was chimney inspected? 3. Did chimney require flue liner system to be installed? If NO, did chimney meet specified criteria as per manual? 4.