Table of Contents
Advertisement
Wing Span: 31.5" (800mm)
Weight: 9.3 oz. (265g)
Wing Span: 31.5"(800mm)
Weight: 9.3 oz. (265g)
Wing Span: 30.7"(780mm)
Weight: 10.5 oz. (300g)
Warranty
:
This kit is guaranteed to be free from defects in material and workmanship at the date of purchase.
It does not cover any damage caused by use or modification. The warranty does not extend beyond the product
itself and is limited only to the original cost of the kit. By the act of building this user-assembled kit, the user
accepts all resulting liability for damage caused by the final product. If the buyer is not prepared to accept this
liability, it can be returned new and unused to the place of purchase for a refund.
Notice: Adult Supervision Required
product requires adult supervision. Read through this book completely and become familiar with the assembly and
flight of this airplane. Inspect all parts for completeness and damage. Contact Thunder Tiger authorized agent if
you find any problem or need tech support.
No. 4316 EXPO 3D Profile EP
Length: 32.17" (817mm)
Motor: 370 with 6: 1 Gear
No. 4317 G202 3D Profile EP
Length: 32.87 (835mm)
Motor: 370 with 6: 1 Gear
No. 4318 Christen Eagle 3D Profile EP
Length: 30.9" (785mm)
Motor: 370 with 6:1 Gear
Wing Area: 252.3 sq.in. (16.28dm
Radio: 4 CH, 3 Micro Servos Req
Wing Area: 258.5 sq.in. (16.68dm
Radio: 4 CH, 3 Micro Servos Req
Wing Area: 369.8 sq.in. (23.86dm
Radio: 4 CH, 3 Micro Servos Req
:
This is not a toy. Assembly and flying of this
2
)
d
* @ 1 ?
- X ?
V ' @ ?
? . Y ?
? S 5 ?
)
2
* @ 1 ?
- X ?
V ' @ ?
d
? . Y ?
? S 5 ?
2
)
* @ 1 ?
- X ?
d
V ' @ ?
? S 5 ?
? . Y ?
Advertisement
Table of Contents
Related Manuals for THUNDER TIGER 4318 Christen Eagle 3D Profile EP
Summary of Contents for THUNDER TIGER 4318 Christen Eagle 3D Profile EP
- Page 1 Read through this book completely and become familiar with the assembly and flight of this airplane. Inspect all parts for completeness and damage. Contact Thunder Tiger authorized agent if you find any problem or need tech support.
-
Page 2: Table Of Contents
I I N N T T R R O O D D U U C C T T I I O O N N All of us at Thunder Tiger want to thank you for choosing the 3D Profile EP series. -
Page 3: Pre-Assembly Notes
If you encounter any assembly question, Nicd or NiMH battery pack of the you may contact Thunder Tiger author ized same capacity. Thunder Tiger distributors or write email to Thunder Tiger directly provide high performance Ace for tech support. Power Lipoly Battery which is at No.2801 3cell 1050mAh... -
Page 4: Part Drawings
PART DRAWINGS Open the box and check that you have all the parts as shown below. If anything is missing please contact your dealer. Parts shown in this page are vary in foamy and linkeg sets of each kit. AS6350 Foamy Set Expo 3D Horizontal Tail (1) Rudder (1) Triangle Balsa Wood (2) - Page 5 PART DRAWINGS Parts shown in this page are same for all 3D Profile EP planes. AS6360 Landing Gear AS6355 Drive Shaft Mount (1) Landing Gear (1) Spur Gear/Drive Shaft (1) E Clip (1) 2x5 mm Pinion (1) Washer Screw (2) Retainer (2) No.
-
Page 6: Assembly
ASSEMBLY / WING ASSEMBLY Expo 3D 1. Check all pre-hinged aileron and elevator, lightly G202 press the taped area and make sure the aileron and elevator will not come apart. You will also have to check this before and after each flight to get precise throws for better performance. -
Page 7: Tail
ASSEMBLY / TAIL Expo 3D 8. Epoxy the tail in place. You may use the rest triangle balsa wood and epoxy it at the bottom of horizontal tail. G202 9. Locate the tail skid, next use hobby knife to cut a slot at the bottom of fuselage tail. -
Page 8: Landing Gear
ASSEMBLY / LANDING GEAR Expo 3D 12.Locate landing gear parts and wheels as shown. 13.Secure the landing gear on plywood with furnished G202 2 x 5mm washer wood screws. Expo 3D Christen Eagle G202 11.Use the furnished tape to tape the Rudder in Christen Eagle place. -
Page 9: Servo
ASSEMBLY / SERVO 19.Install aileron control horns. 15.Install wheels by threading the wheel pant retainer in proper position. 20.Install aileron pushrods as shown. 16.Epoxy the wheel pants on the retainer. Make sure two wheel pants are parallel. 17.Install rudder control horn, slowly inser t the control horn to avoid any damage of surface at 21. -
Page 10: Elevator
ASSEMBLY / SERVO Expo 3D 23.Use the same way to install control horns for elevator and rudder. Expo 3D G202 G202 Christen Eagle 24.Install r udder and elevator ser vo note the orientation of servo output shaft. Above photos Christen Eagle shown are all at left side. -
Page 11: Motor
ASSEMBLY / MOTOR 29.Secure power unit on the fuselage with the 26.Locate all the parts of universal power unit. mounting plates by four 2x8mm self-tapping screws. Drive shaft should be in line with the fuselage without qny thrust angle. 27.Press the bearings all the way in then insert the Spur Gear Drive Shaft. -
Page 12: Rx, Esc, Battery
ASSEMBLY / RX, ESC, BATTERY CONTROL THROWS The following contorl throw of 3D Profile EP is merely a starting point for your radio setup and can be tailored to fit your flying syle. For All three models the aileron and elevator are of the same throws but rudder are different as shown below. -
Page 13: Balance
3D maneuvers. Thank you for purchasing this 3D Profile EP from Christen Eagle Thunder Tiger and we look forward to providing you Note: For the best flight performance of the Christen with other great R/C products in the near future. -
Page 14: Exponetial
ASSEMBLY / 3D SETUP SETTING UP FOR 3D FLIGHT Servo Output High Rate Low Rate Stick Travel Exponetial available in the mar ket and its scener y and performance are just like a real thing. For example, To make your 3D flight successful, the most important Aerofly Pro Deluxe USB version from Ikarus or Real is to set up your radio properly and fine-tune the Flight G3 from Greatplanes are all good simulators... -
Page 15: Flying
ASSEMBLY / 3D SETUP Normally the correct CG position is beneficial to hovering flight. Actually, for 3D profiles its CG range is pretty large. Just give enough control surface movement, softened correctly with exponential throws then you may control the plane at a large range of CG positions. -
Page 16: Ama Safety Code
9) Under no circumstances may a pilot or other person 3) At all flying sites a straight or curved line(s) must be touch a powered model in flight. established in front of which all flying takes place THUNDER TIGER CORPORATION http://www.thundertiger.com JE6695...
Need help?
Do you have a question about the 4318 Christen Eagle 3D Profile EP and is the answer not in the manual?
Questions and answers