Hide thumbs Also See for 510S:

Advertisement

ideacentre All-In-One 510S Computer
Hardware Maintenance Manual
Machine Types: F0C3 [AIO 510S-23ISU / Energy Star]

Advertisement

Table of Contents
loading

Summary of Contents for Lenovo 510S

  • Page 1 All-In-One 510S Computer Hardware Maintenance Manual Machine Types: F0C3 [AIO 510S-23ISU / Energy Star]...
  • Page 3 All-In-One 510S Computer Hardware Maintenance Manual Machine Types: F0C3 [AIO 510S-23ISU / Energy Star]...
  • Page 4 First Edition (April 2016)27th © Copyright Lenovo 2016. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software are delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925...
  • Page 5: Table Of Contents

    Selecting a startup device ..Replacing the LCD panel module ..Exiting the Lenovo BIOS Setup Utility program . . Replacing the LCD panel module-None Touch . .
  • Page 6 All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 7: Chapter 1. About This Manual

    Chapter 1. About this manual This manual contains service and reference information for Lenovo All-In-One 510S computers listed on the cover. It is intended only for trained servicers who are familiar with Lenovo computer products. Before servicing a Lenovo product, be sure to read the Safety Information.
  • Page 8 All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 9: Chapter 2. Safety Information

    Electrical current from power, telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect any attached power cords, telecommunication cables, network cables, and modem cables before you open the computer covers, unless instructed otherwise in the installation and configuration procedures. © Copyright Lenovo 2016...
  • Page 10 – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.) • If an electrical accident occurs: – Use caution; do not become a victim yourself. ideacentre All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 11: Safety Inspection Guide

    – Switch off power. – Send another person to get medical aid. Safety inspection guide The intent of this inspection guide is to assist you in identifying potential hazards posed by these products. Each computer, as it was designed and built, had required safety items installed to protect users and service personnel from injury.
  • Page 12: Grounding Requirements

    • Connect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices. ideacentre All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 13 To Connect To Disconnect 1. Turn everything OFF. 1. Turn everything OFF. 2. First, attach all cables to devices. 2. First, remove power cords from outlets. 3. Attach signal cables to connectors. 3. Remove signal cables from connectors. 4. Attach power cords to outlet. 4.
  • Page 14 To remove all electrical current from the device, ensure that all power cords are disconnected from the power source. CAUTION: Do not place any object weighing more than 82 kg (180 lbs.) on top of rack-mounted devices. ideacentre All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 15: Chapter 3. General Information

    This chapter provides general information that applies to all computer models covered by this manual. Specifications This section lists the physical specifications for your computer. This section lists the physical specifications for your computer. Type Lenovo All-In-One 510S This section lists the physical specifications. Environment Air temperature: Operating: 10°...
  • Page 16 All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 17: Chapter 4. General Checkout

    • If the computer displays a POST error, go to “POST error codes”. • If the computer hangs and no error is displayed, continue at step 7. 7. If the test stops and you cannot continue, replace the last device tested. © Copyright Lenovo 2016...
  • Page 18 All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 19: Chapter 5. Using The Setup Utility

    1. If your computer is already on when you start this procedure, shut down the operating system and turn off the computer. 2. Press and hold the F1 key then turn on the computer. When the Lenovo BIOS Setup Utility program is displayed, release the F1 key.
  • Page 20 5. Select Save changes and Exit from the menu. Power-On Password When a Power-On Password is set, you cannot start the Lenovo BIOS Setup Utility program until a valid password is typed from the keyboard. Setting, changing, or deleting a Power-On Password Note: A password can be any combination of letters and numbers up to 16 characters (a-z and 0-9).
  • Page 21: Enabling Or Disabling A Device

    To set a Power-On Password, do the following: 1. Start the Lenovo BIOS Setup Utility program (See ”Starting the Lenovo BIOS Setup Utility program” on page 13.) 2. From the Security menu, select Set Power-On Password and press the Enter key.
  • Page 22: Selecting A Startup Device

    Selecting or changing the startup device sequence To view or permanently change the configured startup device sequence, do the following: 1. Start the Lenovo BIOS Setup Utility program (see “Starting the Lenovo BIOS Setup Utility program” on page 13). 2. From the Lenovo BIOS Setup Utility program main menu, select the Startup option.
  • Page 23: Exiting The Lenovo Bios Setup Utility Program

    Exiting the Lenovo BIOS Setup Utility program After you finish viewing or changing settings, press the Esc key to return to the Lenovo BIOS Setup Utility program main menu. You might have to press the Esc key several times. Do one of the following: •...
  • Page 24 All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 25: Chapter 6. Symptom-To-Fru Index

    Check that the following are properly installed: Reseat connectors • Power Cord • On/Off Switch connector • System Board Power Supply connectors • Microprocessor connections Check the power cord. Power Cord Check the power-on switch. Power-on Switch © Copyright Lenovo 2016...
  • Page 26: Post Error Codes

    3. Power-on the computer to re-test the system. 4. Repeat steps 1 through 3 until you find the failing device or component. If all devices and components have been removed and the problem continues, replace the system board. ideacentre All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 27: Chapter 7. Locating Connectors, Controls And Components

    The following illustration shows the location of controls and components on the front of the computer. Attention: Be careful not to block any air vents on the computer. Blocked air vents can cause overheating. 1. Built-in microphones (2) 2. 2D camera © Copyright Lenovo 2016...
  • Page 28 Left and right view The following illustration shows the location of connectors, controls and components on the left and right side of the computer. 1. USB 3.0 connectors ideacentre All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 29 Rear view The following illustration shows the location of connectors and components on the rear of the computer. 1. HDMI button 5. Ethernet connector 2. Power button 6. USB 3.0 connectors (2) 3. Power connector 7. Combo audio jack 4. HDMI connector Chapter 7 Locating connectors, controls and components...
  • Page 30 13. USB board in pull-down assembly 5. Wind shielding 14. EMI cover 6. Motherboard 15. Pull-down assembly bracket 7. Solid state drive (SSD) 16. Camera 8. Middle frame 17. Pull-down assembly cover 9. Speaker system ideacentre All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 31 Identifying parts on the motherboard The motherboard (sometimes called the planar or system board) is the main circuit board in your computer. It provides basic computing functions and supports a variety of devices that are factory-installed or that you can install later. The following illustration shows the location of connectors and components on the front of the motherboard.
  • Page 32 All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 33: Chapter 8. Replacing Hardware

    Attention: Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty Guide that was included with your computer. To obtain copies of the Safety and Warranty Guide, go to the Support Web site at: http://consumersupport.lenovo.com. Note: Use only parts provided by Lenovo.
  • Page 34: Replacing The Keyboard And Mouse

    Remove any media from the drives, shut down the operating system, and turn off the computer and all attached devices. Step 2. Disconnect the adapter from the connector on the computer, then unplug the adapter from electrical outlet. ideacentre All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 35: Removing The Stand Base

    Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the touch screen from scratches or other damage.
  • Page 36 Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the touch screen from scratches or other damage.
  • Page 37: Removing The Stand Holder

    Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the touch screen from scratches or other damage.
  • Page 38: Replacing The Solid State Drive

    Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the touch screen from scratches or other damage.
  • Page 39 Step 8. Remove the four screws that secure the storage converter to the chassis, and then remove the storage converter. Step 9. Remove the four screws that secure the solid state drive to the storage converter, and then remove the solid state drive from the converter. Chapter 8 Replacing hardware...
  • Page 40: Removing The Emi Cover

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 41: Replacing The Power Switch Board

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 42: Replacing The Wi-Fi Card

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 43: Replacing The Memory Module

    Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the touch screen from scratches or other damage.
  • Page 44: Replacing The System Fan

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 45: Replacing The Heat-Sink

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 46: Removing The Wind Shielding

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 47: Replacing The Motherboard

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 48: Replacing The Speaker System

    Step 16. Reattach the EMI cover, stand holder, rear cover, and stand base. Replacing the speaker system Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. ideacentre All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 49: Removing The Pull Down Assembly

    Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 50: Replacing The Camera

    Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 51 Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 52: Replacing The Usb Board In The Pull Down Assembly

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 53 Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Locating connectors, controls and components to locate the various connectors. Step 4. Remove the stand base.
  • Page 54: Replacing The Lcd Panel Module

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 55 Step 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to Locating connectors, controls and components to locate the various connectors. Step 4. Remove the stand base.
  • Page 56 Step 16. Remove the LVDS cable and converter cable from the connectors in the LCD panel. Step 17. Remove the twenty one screws that secure the middle frame to the LCD panel. ideacentre All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 57 Step 18. Pull the middle frame in the directions as shown until the panel and middle frame are separated. Chapter 8 Replacing hardware...
  • Page 58 Connect the system fan cable, solid state drive cable and power switch board cable to the corresponding connectors on the motherboard. m. Reattach the EMI cover to the chassis. Reattach the stand holder to the chassis. Reattach the rear cover. ideacentre All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 59: Replacing The Lcd Panel Module-None Touch

    Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 60 Step 15. Remove the LVDS cable and converter cable from the connectors in the LCD panel. Step 16. Remove the twenty one screws that secure the middle frame to the LCD panel. ideacentre All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 61 Step 17. Pull the middle frame in the directions as shown until the panel and middle frame are separated. Chapter 8 Replacing hardware...
  • Page 62 Connect the system fan cable, solid state drive cable and power switch board cable to the corresponding connectors on the motherboard. m. Reattach the EMI cover to the chassis. Reattach the stand holder to the chassis with the four screws. Reattach the rear cover. Reattach the stand base. ideacentre All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 63: Chapter 9. Fru Lists

    Chapter 9. FRU lists This chapter lists the information on the field replaceable units (FRUs) for ideacentre All-In-One 510S-23ISU desktop computer. Attention: Be sure to read and understand all the safety information before replacing any FRUs. Notes: FRUs that have a 1 or 2 in the CRU column are Customer Replaceable Units (CRUs).
  • Page 64 Sunrex EKB-10YA(SP) W-Silk USB KB-LVT8 25216259 Liteon SK-8861(LA) 2.4G KB-improved8 25209157 Sunrex EKB-10YA(GE) W-Silk USB KB-LVT8 25209147 Sunrex EKB-10YA(TW) W-Silk USB KB-LVT8 25216257 Liteon SK-8861(GB) 2.4G KB-improved8 25209145 Sunrex EKB-10YA(US) W-Silk USB KB-LVT8 ideacentre All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 65 25216266 Liteon SK-8861(FR) 2.4G KB-improved8 25216263 Liteon SK-8861(TR) 2.4G KB-improved8 25216270 Liteon SK-8861(BE-EN) 2.4G KB-improved8 25209169 Sunrex EKB-10YA(EN-FR) W-S USB KB-LVT8 25201322 Sunrex LXH-EMS-10ZA W-Silk Mouse 25216253 Liteon SK-8861(TH) 2.4G KB-improved8 25209158 Sunrex EKB-10YA(TR) W-Silk USB KB-LVT8 25209154 Sunrex EKB-10YA(LA) W-Silk USB KB-LVT8 25216043 Liteon ZTM600 2.4G Mouse (WW) Silver 25216264...
  • Page 66 01EF267 ASSY_HDD_Cage 01EF262 ASSY_Front_Deco 01EF326 WIFI_ANTENNA_L&R_A510S 01EF264 ASSY_Pull-down_Cover 01EF269 Fin_Cover 01EF325 Pull-down_Bracket 03T7413 4G,SODIMM,DDR4,2133MHz 03T7415 16G,SODIMM,DDR4,2133MHz 03T7414 8G,SODIMM,DDR4,2133MHz 00PC593 Doking M680B W-Silk USB MC WHT 00XG043 EX-ODD DVD Burner DB65 01EF324 SCREW LIST,A510S ideacentre All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 67 00KT011 256G,2.5",7mm,SATA6G,SAMSG,STD 00KT046 ASM LIT V2+ 256GB 01EF260 ASSY_M_AIO510S_Base 01EF259 ASSY_M_AIO510S_UP 00JT477 Wireless,CMB,LTN,NFA435 00JT507 Wireless,CMB,IN,3165 ac Ind 00JT497 Wireless,CMB,IN,3165 ac Chapter 9 FRU lists...
  • Page 68 All-In-One 510S Computer Hardware Maintenance Manual...
  • Page 69: Chapter 10. General Information

    • Wake Up on Alarm: You can specify a date and time at which the computer will be turned on automatically. This can be either a single event , a daily event or a weekly event. • Wake Up on LAN: This feature allows LAN adapter card to wake the System. © Copyright Lenovo 2016...

Table of Contents