CognitiveTPG A798 Programming Manual page 13

Revision D 10/13
*** A799 - Diagnostics Form ***
*** A798 – Diagnostics Form ***
*** A795 - Diagnostics Form ***
Model number
Model number
Serial number
Serial number
Model number
Boot Firmware
Serial number
Boot Firmware
Revision
Revision
CRC
Boot Firmware
P/N
CRC
Revision
Flash Firmware
P/N
CRC
Revision
P/N
Flash Firmware
CRC
Flash Firmware
Revision
P/N
Revision
CRC
CRC
H/W parameters
P/N
P/N
Flash Memory Size
Flash Logos/Fonts
H/W parameters
H/W parameters
Flash User Storage
Flash Memory Size
Flash Memory Size
SRAM Size
Flash Logos/Fonts
Head Setting
Flash Logos/Fonts
Flash User Storage
Paper Type Name
Flash User Storage
Flash Perm'nt Fonts
Color Density Adj
Flash Perm'nt Fonts Flash Journal Size
Print Density (Mono)
SRAM Size
Flash Journal Size
Max Speed
Head setting
SRAM Size
Paper Width
Pre-Heating
Max Power
Head settting
Print Density
Knife
Motor ID
Max Speed
Partial Cut
Paper Width
Paper Type Setting
Paper Low Sensor
Max Power
Color Density Adj
Knife
Print Density, Mono Comm. Interface
Partial Cut
RX Buffer Size
Max Speed
Paper Low Sensor
Interface type
Paper Width
Parameters
Comm. Interface
Max Power
Baud Rate
RX Buffer Size
Knife
Data Bits
Interface type
Stop Bit
Partial Cut
Parameters
Parity
Paper Low Sensor
Baud Rate
Flow Control
Data Bits
No Paper Low Extension
Reception Errors
Stop Bit
Alternate DTR/DSR : Disabled
Parity
Comm. Interface
Flow Control
Resident Code Pages
RX Bu er Size
Reception Errors
Interface Type
USB Driver Type
USB Packet w/Error
Parameters
Baud Rate
Available Paper Types
Resident Code Pages
Data Bits
Stop Bit
Logo (s) defined
Parity
User Char(s) defined
Flow Control
Logo(s) defined
Reception Errors
User Char(s) defined
USB Driver Type
To enter Printer Config Menu :
Journal Unused
USB Packet w/Error 1) Flip DIP switch #1 down
2) Reset the printer, while holding
the Paper Feed button down
To enter Printer Config Menu
1) Flip DIP switch #1 down
2) Reset the printer, while holding
the Paper Feed button down
Print test and configuration menu samples will vary per model or printer
For more information about
Accessing the remote diagnostic tallies
*********
*******************************
: A795-2119
: A799-120D-TD00
: A012251287
: 0000000000
Select a sub-menu :
: A798-720D-TD00
- EXIT
: C073400014
- Print Current Configuration
: V1.02
- Set Communication Interface
: V3.02
: 76EB
- Set Diagnostics Modes
: 189-1076076A
: 7E22
: V3.04
- Set Emulation/Software Options -> 5 clicks
: 189-7940489B
: 74D1 - Set Hardware Options
: V1.13
: 189-798B304A
- Set Paper Type
: AB62
: V3.01
: 189-7950290A
: V3.01
Enter code, then hold Button DOWN
: 4448
: 4FFF at least 1 second to validate
: 189-7940490A
: 189-7940497A
: 2 Mbyte
: 1024 kbytes
: 0 kbytes
: 2 Mbytes
: 4 Mbytes
: 256 kbytes
: 1152 kbytes
: D
: 1024 kbytes
: 64 kbytes
: Type 5, Version 0
: 960 kbytes
: 0 kbytes
: 100 %
: 960 kbytes : 64 kbytes
: 100 %
: 128 kbytes
: 128 kbytes
: 100 mm/sec
: C
: 512 kbytes
: 80 mm
: Disabled
: 55 W
: D
: 100%
: Enabled
: 1
: 150 mm/sec
: 135 steps
: 80 mm
: Type 0, Monochrome
: Disabled
: 55 W
: n/a
: Enabled
: 100%
: 125 steps
: 4096
: 250 mm/sec
: Disabled
: RS232/USB
: 80 mm
: 55 W
: 115200
: 4096
: Enabled
: 8
: RS232/USB
: 1
: 125 steps
: NONE
: Enabled
: 115200
: DTR/DSR
: 8
: Ignore
: 1
: NONE
: DTR/DSR
: 437, 850, 852, 858
: 4096
: Ignore
860, 863, 865, 866
: RS232/USB
: Printer Class
1252, 862, 737
: Reject
: 115200
: 00.00 01.00 05.00
: 437, 850, 852, 858
01.90 01.92 01.93
: 8
860, 863, 865, 866
: 1
1252, 862, 737, 857
: YES
Current Printer tallies are
: NONE 1251, 1255, KZ-1048
: NO
}
printed after the Diagnostic
: DTR/DSR
: YES
: Ignore
information and will vary
: NO
: Printer Class
per printer use.
: 64 kbytes
: Reject
:
configuration. (Shown approximately 60% of size.)
See this section
"Command descriptions" in Chapter 4: Programming commands
(Status commands: Transmit printer ID, remote diagnostics extension,
Hexadecimal 1D 49 40 n)
A798-PG00001D
Chapter 2: Diagnostics and Configuration
**********
MAIN MENU
-> 1 click
-> 2 clicks
-> 3 clicks
-> 4 clicks
-> 6 clicks
-> 7 clicks
- Set Firmware Features - > 8 clicks
13