Table of Contents
Advertisement
Quick Links
Int6028
Int6028
Sirocco Series
SMD Rework Station
Thank you for purchasing the Aoyue 6028 Rework Station.
Please read the manual before using the unit.
Keep manual in accessible place for future reference.
Manufacturer:
AOYUE TONGYI ELECTRONIC EQUIPMENT FACTORY
Jishui Industrial Zone, Nantou, Zhongshan City,
Guangdong Province, P.R.China
http://www.aoyue.com
24
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for aoyue int6028
Summary of Contents for aoyue int6028
- Page 1 Int6028 Int6028 Sirocco Series SMD Rework Station Thank you for purchasing the Aoyue 6028 Rework Station. Please read the manual before using the unit. Keep manual in accessible place for future reference. Manufacturer: AOYUE TONGYI ELECTRONIC EQUIPMENT FACTORY Jishui Industrial Zone, Nantou, Zhongshan City, Guangdong Province, P.R.China http://www.aoyue.com...
- Page 2 REPLACEMENT AIR NOZZLES This manual is designed to familiarize and instruct the technician with the proper operation and maintenance of the equipment. The “Care and Safety Precautions” section explains the hazards of using any type of soldering or reworking device. Please read carefully and observe the guidelines in order to maximize usage and minimize the risk of injury or accidents .
-
Page 3: Table Of Contents
BASIC TROUBLESHOOTING GUIDE PROBLEM 4: DISPLAY SHOWS UNRECOGNIZABLE CHARACTERS TABLE OF CONTENTS SOLUTION: Turn on the main power switch ad on again , if the problem persists have the unit serviced by a qualified technician. Product Description …………………………………… PROBLEM 5: OTHER PROBLEMS NOT MENTIONED IN THIS DOCUMENT Package Inclusion …………………………………… SOLUTION: Please bring the unit to a certified service station. Specifications …………………………………… Functions and Features ……………………………… Safety Precautions ……………………………………... -
Page 4: Product Description
PRODUCT DESCRIPTION PROBLEM 1: THE UNIT HAS NO POWER 1. Check if the unit is switched ON. The Aoyue 6028 hand held reflow system is a reworking 2. Check the fuse. Replace with the same type if fuse is blown. equipment that produces hot air reworking conditions analogous to 3. Check the power cord and make sure there are no disconnections. ... -
Page 5: Package Inclusion
CARE AND MAINTENANCE PACKAGE INCLUSION 排除故障指南 Aoyue 936 规格 Replacing the heating element When the heating element has reached the end of its life or has been damaged it may need to be replaced. The following steps ... -
Page 6: Specifications
CARE AND MAINTENANCE SPECIFICATION SPECIFICATION SPECIFICATION Heating element The following steps would help prolong the life of the heating element. Always let the unit enter cool down and sleep mode first before ◆ MAIN STATION turning off the unit. Always turn the temperature knob fully counter clockwise and ◆ Power Input : available in 110V / 220V airflow level at around mid point after each use. Note: Overheat protection is automatically enabled Station Dimensions: ... -
Page 7: Functions And Features
FUNCTIONS and FEATURES OPERATING GUIDELINES Aoyue 936 规格 D. AFTER REWORKING/EXTRACTION 1. Replace hot air gun into is holder. the heater LED would turn off ESD safe hand piece. ● signifying it is now on cool down mode. Note: The airflow can be Auto cool down feature, unit shuts off heating element then ... -
Page 8: Safety Precautions
SAFETY PRECAUTIONS OPERATING GUIDELINES Soldering: CAUTION: Improper usage can cause serious injury to personnel and/or damage to equipment and work area. For your own safety, please observe 1. Follow procedures in, “A. INITIAL PROCEDURES”. the following precautions. 2. Prepare the unit to be worked upon on a stable elevated Check ... -
Page 9: Assembly And Preparation
OPERATING GUIDELINES ASSEMBL Y and PREPARATION 焊铁头的维护和使用 Aoyue 936 规格 D. TRADITIONAL REWORKING GUIDE: Hot air gun holder Traditional reworking : 1. Install the Hot air gun holder, the hot air gun holder is detached SP2000 The hand held reflow gun is also well suited for traditional reflow for shipping purposes . soldering and extraction, the following is a brief guide on reworking via 2. Slide in the metal arm of the hot air gun holder into the slit ... -
Page 10: Control Panel Guide
OPERATING GUIDELINES CONTROL PANEL GUIDE Aoyue 936A 规格 Aoyue 936 规格 SPECIFICATION Stage 2: Flux activating 1. The entire PCB temperature should be around 150 to 160 °C after stage 1. 2. To activate flux, lower the nozzle of the hot air gun by about ... -
Page 11: Operating Guidelines
OPERATING GUIDELINES OPERATING GUIDELINES Aoyue 936 规格 Aoyue 936 规格 SPECIFICATION C. REWORKING GUIDE: Convection style reworking : The hand held convection style reworking is a newly developed REMINDERS: reworking style that reproduces the reflow oven soldering stages using 1. Make sure the equipment is placed on a flat stable surface and all the only a portable hand held reflow gun. ... -
Page 12: Initial Procedures
OPERATING GUIDELINES OPERATING GUIDELINES 保养 Aoyue 936 规格 SPECIFICATION A. INITIAL PROCEDURES 4. Turn the airflow knob to medium airflow. 5. Turn the temperature knob at about 250°C. 1. Plug the device to the main power source using the power cord 6. Lift up the hot air gun and hold it vertically on top of the target provided in the package. device, leaving approximately 2cm of space between the tip of 2. Secure the hot air gun on its holder. the hot air gun and the target device. ...
Need help?
Do you have a question about the int6028 and is the answer not in the manual?
Questions and answers