Subscribe to Our Youtube Channel
Related Manuals for Stern B-280210
Summary of Contents for Stern B-280210
- Page 1 INSTALLATION AND MAINTENANCE GUIDE B E H I N D M I R RO R TOU C H F R E E S OA P D I S P E N S E R...
- Page 2 I N DEX TECHNICAL DATA PRE-INSTALLATION INFORMATION PACK CONTENTS INSTALLATION FILLING THE SOAP TANK SETTINGS ADJUSTEMENT WITH A REMOTE CONTROL BATTERIES REPLACEMENT MAINTENANCE Care and cleaning of chrome and special finishes SPARE PARTS LIST WARRANTY TROUBLE SHOOTING...
-
Page 3: Technical Data
TE CHN ICAL DATA Behind mirror Soap Dispenser B - 280210 Behind mirror Soap Dispenser E - 280200 1 Liter \ 33.8 oz. Capacity: IP 67 Battery Box for 6xD Alkaline batteries \ Transformer Power Supply: 100 – 3800 cPs Soap viscosity: Standard discharge: 0.8cc, Adjustable Sensor range:... -
Page 4: Pre-Installation Info
PRE-INSTALLATION INFO Check contents Separate all parts from the packaging and check each part with the “Pack contents” section. Make sure all parts are accounted for before discarding any packaging material. If any parts are missing, do not attempt to install your touch free soap dispenser until you obtain the missing parts. -
Page 5: Pack Contents
PACK CO NT EN TS Familiarize yourself with the part names and confirm that the parts are included. 4 screws up to 5mm (not supplied) B V E R S I O N S E V E R S I O N S IP 67 Battery Product assembly Box for 6xD... -
Page 6: Installation
INSTALLATION STEP 1 – PREPARATION FOR INSTALLATION Cut a hole in the bottom of the mirror compartment for the soap dispenser sensor and spout both. The recommended hole size should be 30x50 mm 50 mm 30 mm STEP 2 – INSTALLING THE SOAP DISPENSER Remove the protective sticker covering the sensor. - Page 7 INSTALLATION Secure the plate to the wall with 4 screws (not supplied). STEP 3 - CONNECTING THE POWER SOURCE Make sure that the 4 contacts connector is connected properly so that the white o-ring is not O-ring visible – not connected properly visible.
- Page 8 INSTALLATION For battery versions: Install the battery box at the wall in the mirror compartment and connect the battery connector. For transformer versions: Plug the transformer into the electricity socket and make sure the transformer connector is connected. Wait about 10 seconds before you put your hands within the sensor range.
-
Page 9: Filling The Soap Tank
FILLING THE SOAP TANK 1. Unscrew the soap 2. Fill in the liquid tank from the pump soap up to the top assembly. line. 4. Screw the soap tank back to the 3. Insert the bottle pump assembly. with the tube inside Make sure the tank the bottle support. - Page 10 SETTINGS ADJUSTEMENT WITH A REMOTE CONTROL If desired, use the remote control to adjust the soap dispenser settings. Hold the remote control straight in front of the sensor in a distance of about 4-6” (10-15cm). Attention: Holding the soap dispenser remote control out of the recommended range (too close or too far)may interfere with the remote’s activation.
- Page 11 BATTERY REPLACEMET Battery models only When the battery weakens, the red indicator light will blink at a constant rate when the user’s hands are within the sensor range. The battery must be replaced within two weeks. To replace the battery in battery models: 1.
-
Page 12: Maintenance
MAINTENANCE Care and cleaning of chrome and special finishes DO NOT use steel wool or cleansing agents containing alcohol, acid, abrasives, or the like. Use of any prohibited cleaning or maintenance products or substances could damage the surface of the soap dispenser. For surface cleaning use ONLY soap and water, then wipe dry with a clean cloth or towel. -
Page 13: Spare Parts List
SPARE PARTS LIST Sensor kit 07220230 Soap tank 1 L 07100020 Transformer 06522042 Soap dispenser Pump assembly 07222001 Remote control 07100008 IP67 transformer box 06530021 IP 67 Battery Box for 6xd alkaline batteries 06530041 Bottle support 1 L 07120175 Soap dispenser spout assembly 07271023... -
Page 14: Limited Warranty
If a defect is found in normal use, Y. Stern Engineering Ltd. will, at its discretion, repair, provide a replacement part or product, or make appropriate adjustments. -
Page 15: Troubleshooting
TROUBLE SHOOTING P R O B L E M I N D I C AT O R C A U S E S O L U T I O N Red light in the sensor flashes continuously when Low battery. Replace battery. - Page 16 15 Gan Rave Blvd., 81222 Gan Rave, Yavne, Israel Tel: 972-8-9326000, Fax: 972-8-9326025, export@sternfaucets.com www.sternfaucets.com...
Need help?
Do you have a question about the B-280210 and is the answer not in the manual?
Questions and answers