Timer Recording; Code ® System To Make Timer Recordings - Panasonic Diga DMR-E65 Operating Instructions Manual

Timer recording

DVD
TV
INPUT SELECT
AV
DVD DRIVE SELECT
1 2
Numbered
4 5
buttons
7 8
CANCEL
¢ CANCEL
0
SKIP
STOP
DIRECT NAVIGATOR
DIRECT
NAVIGATOR
TOP MENU
3,4,2,1
ENTER
SUB MENU
PROG/CHECK
DISPLAY
PROG/CHECK
TIMER ERASE
F TIMER
F
A B
[RAM] [DVD-R]
You can enter up to 16 programmes up to a month in advance.
Using G- ® system to make timer
CODE
recordings
Entering G- numbers is an easy way of timer recording. You can
CODE
find these numbers in TV listings in newspapers and magazines.
1
Press [G-Code].
G-Code
Remain
12:53:00 15. 7. TUE
Enter G-Code Number by using 0-9 keys.
2
Press the numbered buttons to enter
the G- number.
CODE
Press [2] to move back to correct a digit.
3
Press [ENTER].
TIMER
Remain
RECORDING
12:54:00 15. 7. TUE
Name Date Start Stop Mode
1 ARD 15/ 7 TUE 19:00 20:00 SP
Programme Name
≥Confirm the programme and make corrections if necessary
using [3, 4, 2, 1] (➡page 18, step 3).
≥When "-- ---" appears in the "Name" column, you cannot set
timer recording. Press [3, 4] to select desired programme
position. After you have entered the information of a TV
station, it is kept in the unit's memory.
≥You can also press [REC MODE] to change the recording
mode.
≥Programme Name
Press [2, 1] to select "Programme Name" and press
[ENTER] (➡ page 38).
VOLUME
CH
SD/PC
3
CH
6
G-Code
9 G-Code
MANUAL SKIP
-/--
SLOW/SEARCH
PAUSE PLAY/x1.3
PLAY
FUNCTIONS
ENTER
RETURN
STATUS TIME SLIP
REC MODE REC
REC MODE
CREATE
AUDIO
CHAPTER
C
1:58 SP
1:58 SP
4
Press [ENTER].
The settings are stored.
TIMER
Remain
RECORDING
12:55:00 15. 7. TUE
Disc
No. Name Date Start Stop Mode
space
01 ARD 15/ 7 TUE 19:00 20:00 SP OK
New Timer Programme
Repeat steps 1–4 to programme other recordings.
5
Press [F TIMER].
The unit turns off and "F" lights on the unit's display to
indicate timer recording standby has been activated.
[RAM]
Even if the unit is in timer recording standby, play starts when you
press [1] (PLAY) or [DIRECT NAVIGATOR]. Timer recording works
even during play.
∫ To release the unit from recording standby
Press [F TIMER].
The unit turns on and "F" goes out.
≥Be sure to press [F TIMER] before the programme start time to
put the unit on recording standby. Timer recording will work only
if "F" is displayed.
∫ To cancel recording when recording has
already begun
Press [F TIMER].
≥You can also press and hold [∫] on the main unit for more than
3 seconds to stop recording.
[Note]
≥"F" flashes for about 5 seconds when the unit cannot go to
timer recording standby (e.g., a recordable disc is not in the
disc tray).
≥If the unit is not put in the timer recording standby mode at the
latest 10 minutes before the programmed timer recording
starting time, the "F" flashes on the unit display. In this case,
press [F TIMER] to put the unit in the timer recording standby
mode.
≥When you programme successive timer recordings to start
immediately one after the other, the unit cannot record the part
at the beginning of the later programmes (a few seconds when
recording with DVD-RAM and approximately 30 seconds when
recording with DVD-R).
1:58 SP
Check to make sure
"OK" is displayed
(➡page 19).
RQT7450
17