Table Of Contents; Lead Of Wiring - Panasonic TH-50PZ77U Service Manual

TH-50PZ77U
FEATURES
Dimensions (W × H × D)
Including pedestal
TV Set only
Mass
Including pedestal
TV Set only
Note:
· Design and Specifications are subject to change without notice. Mass and Dimensions shown are approximate.
CONTENTS
1 Applicable signals
2 Safety Precautions
2.1. General Guidelines
3 Prevention of Electrostatic Discharge (ESD) to
Electrostatically Sensitive (ES) Devices
4 About lead free solder (PbF)
5 Service Hint
6 Plasma panel replacement method
6.1. Remove the Back cover
6.2. Remove the fan A/B/C
6.3. Remove the rear terminal cover
6.4. Remove the tuner unit
6.5. Remove the DG-Board
6.6. Remove the H-Board
6.7. Remove the P-Board
6.8. Remove the side AV unit and the side AV bracket.
6.9. Remove the G-Board and GS-Board
6.10. Remove the PB-Board
6.11. Remove the D-Board
6.12. Remove the SU-Board
6.13. Remove the SD-Board
6.14. Remove the SC-Board
6.15. Remove the SS-Board
6.16. Remove the stand brackets
6.17. Remove the C1-Board
6.18. Remove the C2-Board
6.19. Remove the C3-Board
6.20. Remove the C4-Board
6.21. Remove the C5-Board
6.22. Remove the C6-Board
6.23. Remove the speaker L, R
6.24. Remove the Plasma panel section from the Cabinet assy
(glass)
6.25. Remove the K-Board and the S-Board
3D Y/C FILTER
CLOSED CAPTION
Photo Viewer
52.1 " × 31.6 " × 14.6 " (1,323 mm × 802 mm × 369 mm)
52.1 " × 29.7 " × 3.92 " (1,323 mm × 754 mm × 99.5 mm)
111.3 lb. (50.5 kg)
94.8 lb. (43 kg)
Page
4
5
5
6
7
8
9
9
9
9
9
10
10
10
11
12
12
13
13
13
13
14
14
14
14
15
15
15
15
16
16
16
V-Chip
HDAVI Control 2
6.26. Replace the plasma panel (finished)
7 Caution statement
7.1. Caution statement.
8 Location of Lead Wiring
8.1. Lead of Wiring (1)
8.2. Lead of Wiring (2)
8.3. Lead of Wiring (3)

8.4. Lead of Wiring (4)

8.5. Lead of Wiring (5)
8.6. Lead of Wiring (6)
8.7. Lead of Wiring (7)
9 Self-check Function
9.1. Check of the IIC bus lines
9.2. Power LED Blinking timing chart
9.3. No Power
9.4. No Picture
9.5. Local screen failure
10 Service Mode
10.1. How to enter into Service Mode
10.2. Service tool mode
11 Adjustment Procedure
11.1. Driver Set-up
11.2. Initialization Pulse Adjust
11.3. P.C.B. (Printed Circuit Board) exchange
11.4. Adjustment Volume Location
11.5. Test Point Location
12 White Balance Adjustment
12.1. White balance adjustment
13 Hotel mode
14 Conductor Views
14.1. P(1)-Board
14.2. P(2)-Board
14.3. G,GS,K and S-Board
14.4. PB-Board
2
Page
17
18
18
19
19
20
21
22
23
24
25
26
26
27
28
29
30
31
31
33
34
34
35
35
36
36
37
37
39
41
41
43
44
45