Page 1
LOT NUMBER: DATE PURCHASED: Audio Video Tower Model # AVTEC48-TC ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your...
Page 2
M A X I M U M R E C O M M E N D E D W E I G H T L O A D S MANUFACTURER: Whalen Furniture Mfg., Inc. CATALOG: Audio Video Tower (AVTEC48-TC) DATE OF MANUFACTURE: July 2013 MADE IN CHINA MAXIMUM LOAD 50 lb.
Page 3
Model # AVTEC48-TC Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Top Shelf Frame (1) B- Middle Upper Shelf Frame (1) C- Middle Shelf Frame (1)
Page 4
Model # AVTEC48-TC Assembly Instructions Flat Washer 1-1/4” Bolt Lock Washer (2 used in this step) (10 used in this step) (2 used in this step) ⑥ ④ ⑦ NOTE: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled, go back and fully tighten all bolts.
Page 5
Model # AVTEC48-TC Assembly Instructions 7/8” Bolt Shelf Pin (4 used in this step) (4 used in this step) ③ ⑧ 4. Screw 2 Shelf Pins (8) into the designated threaded sockets on the Left Leg (G). As shown. 5. Align and attach the Left Leg (G) to the Middle Shelf Frame (C) and Bottom Shelf Frame (E).
Page 6
Model # AVTEC48-TC Assembly Instructions 1-1/8” Bolt (2 used in this step) ⑤ 7. Stand the unit upright. 8. Insert two 1-1/8” Bolts (5) through the pre-drilled holes on the back rail of the Top Shelf Frame (A) and screw into the threaded sockets on the Legs (G and H).
Page 7
Model # AVTEC48-TC Assembly Instructions 1-1/8” Bolt Lock Washer Flat Washer 5/8” Bolt (2 used in this step) (2 used in this step) (2 used in this step) (2 used in this step) ⑥ ⑤ ⑦ ② 9. Align and attach one Top Shelf Support (N) to the “L” bracket of the Top Shelf Frame (A) using one 5/8”...
Page 8
Model # AVTEC48-TC Assembly Instructions 5/8” Bolt (4 used in this step) ② 11. Attach 2 Cable Wheels (O) to the backside of the Spine (F) and tighten with the enclosed Allen Wrench. 12. The Cable Wheels allow you to organize, route and separate your component cords and cables to minimize tangling and signal interference.
Page 9
Model # AVTEC48-TC Assembly Instructions Suction Cup (20 used in this step) ① 14. Put the Suction Cups (1) firmly into the top holes and the inside corner plates on the Shelf Frames (A, B, C, D and E). TIP: If a suction cup resists insertion, try pressing down on the middle of the cup with the Allen Wrench while twisting it clockwise into the hole.
Page 10
Model # AVTEC48-TC Assembly Instructions Tools required: Allen Wrench (provided), Phillips screwdriver, Mallet, Power Drill, and 3/8” Drill Bit. 16. Position the assembled tower at the desired location against a wall. If necessary, adjust the pre-attached Floor Levelers on the bottom of the Legs (G and H) to level the unit.
Should this product be defective in workmanship or materials or fail under normal use, we will repair or replace it for up to one (1) year from the date of purchase. Every Whalen Furniture product is designed to meet your highest expectations. We guarantee that you will immediately see the value of our fine furniture.