Table of Contents
Advertisement
Quick Links
Operating Instructions
Vacuum Cleaner
MC-E590, MC-E591, MC-E593
Shop
@
For Accessories and Consumables visit our web site at
www.panasonic.co.uk
(for customers in the UK only)
We would recommend that you read these Operating Instructions before attempting to operate the unit
and that you note the Important Safety Instructions.
Please keep in a safe place with your Authorised Dealer Service booklet.
This product complies with the directives 73/23/EEC and 89/336/EEC.
Advertisement
Table of Contents
Related Manuals for Panasonic MC-E593
Summary of Contents for Panasonic MC-E593
-
Page 1: Operating Instructions
Operating Instructions Vacuum Cleaner MC-E590, MC-E591, MC-E593 Shop For Accessories and Consumables visit our web site at www.panasonic.co.uk (for customers in the UK only) We would recommend that you read these Operating Instructions before attempting to operate the unit and that you note the Important Safety Instructions. -
Page 2: Table Of Contents
If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. -
Page 3: Important Safety Instructions For The User
• Do not use with damaged power supply cord or plug. If the vacuum cleaner is not working as it should be, or has been dropped, damaged, left outdoors, or come into contact with water, consult an authorised Panasonic Service Centre. -
Page 4: Identification Of Main Parts
IDENTIFICATION OF MAIN PARTS A-1) Handle B-1) Upper cord hook (MC-E590 only) D) Dust sensor indicator (MC-E593 only) A-3) Hose clip C) ON/OFF Switch and Hose Variable power control (MC-E590 ON/OFF Switch only) B-1) Lower cord hook (MC-E590 only) Release handle... -
Page 5: How To Assemble / Operate Your Cleaner
HOW TO ASSEMBLE / OPERATE YOUR CLEANER A) HANDLE ASSEMBLY Handle screw Dusting brush Hose clip 1) Remove the dusting brush from 2) Insert the base of the handle into 3) Re-install the dusting brush the handle and line the handle up in its storage position. -
Page 6: C) Dust Compartment Operation
This is used when maximum sensor. Only for MC-E593 suction is required. NOTE: When using tools, press the model. beater bar pedal to the OFF position. -
Page 7: E) Dust Sensor (Mc-E593 Only)
E) DUST SENSOR (MC-E593 only) The dust sensor indicator automatically informs you of the cleaning conditions. When dust is present in the air being vacuumed the red indicator lights and remains lit until the air is free of dust. The Red light then goes off indicating the area is free of dust. -
Page 8: H) How To Use The Accessories
G) FLOOR SCRATCH / CARPET DAMAGE PREVENTION Carpeted floor Hard floor To prevent scratches or other damage to hard To avoid damaging carpeted floors or rugs, do not floors, Linoleum etc., switch the beater bar off leave the beater bar rotating in the same place for using the pedal. -
Page 9: Maintenance And Servicing
MAINTENANCE AND SERVICING IMPORTANT NOTE: Before servicing any part, always DISCONNECT THE CLEANER FROM THE MAINS SUPPLY HOW TO EMPTY THE DUST COMPARTMENT IMPORTANT: Empty the dust compartment when the dust reaches the ( MAX) mark. Filter wiper handle 1) Release the dust compartment 2) Before opening the dust cover 3) To open the dust cover, turn lock as shown and pull it forward. -
Page 10: Filter Care
FILTER CARE Central Filter (Fig. 1 ) Part no.: AMC8F03W5000 The central filter (foam filter), is located in the main body under the dust compartment to protect the motor from dirt. Remove the dust compartment to gain access to the central filter (see page 9). To remove the central filter, hold the filter at the top (as illustrated) and pull upwards. -
Page 11: Blockages
Pre-filter cleaning If the pre-filter becomes very dusty, or threads etc get wrapped around the pre-filter, it should be cleaned. To clean or replace the pre-filter: Remove the dust compartment, then remove the dust cover (see Page 9). Arrow Pre-filter Claw Replacing pre-filter part nº: AMC8F40W5100... -
Page 12: Maintenance For The Beater Bar
MAINTENANCE FOR THE BEATER BAR CAUTION: Ensure the cleaner is DISCONNECTED from the mains supply before any beater bar maintenance. TO AVOID ANY PERSONAL INJURY: If it is necessary to remove threads, strings, • Do not use your fingers or hands to remove hairs, etc., which have wound around the or clean the beater bar. -
Page 13: Trouble Shooting Guide
(see page 10 FILTER CARE) main filter. NOTE: If the flexible power supply cord becomes damaged, it must be repaired by Panasonic, or an Authorised Service Centre or a qualified person in order to avoid any hazard. – 13 –... -
Page 14: Specifications
SPECIFICATIONS MC-E590 MC-E591 MC-E593 Power source 230-240V~50Hz 230-240V~50Hz 230-240V~50Hz Max. output 1500W 1500W 1600W Nominal output 1200-1300W 1200-1300W 1300-1400W Dimensions (WxLxH) mm 360x305x1100 360x305x1100 360x305x1100 Net weight 8,7 Kg 8,9 Kg 8,9 Kg Dusting brush Upholstery nozzle Crevice nozzle Extension wand HEPA Filter Design and specifications may be changed without notice. -
Page 15: Consumables / Accessories
• Or go online through our Internet Accessory ordering application at www.panasonic.co.uk • Most major credit and debit cards accepted. • All enquiries, transactions and distribution facilities are provided directly by Panasonic UK Ltd. • It couldn’t be simpler! – 15 –... - Page 16 Matsushita Electric España, S.A. VACUUM CLEANER DIVISION Zona Industrial del Polígono de CELRÀ 17460 CELRÀ (Girona) SPAIN 100% recycled paper Z07W51900 Printed in Spain...