Manual Programming - Panasonic DMR-E30 Operating Instructions Manual

Manual programming

[RAM] [DVD-R]
Remote control only
You can set your own programming conditions (up to 16
programmes).
Preparation
≥ Switch [DVD, TV] (15) to "DVD".
≥ Ensure that this unit's clock is set correctly.
≥ Insert a disc for recording (make sure there is enough room for
the programme you are going to record plus a little extra).
Press [PROG/CHECK] (13).
1
≥ The Timer Programme List screen appears.
TIMER
Remain
RECORDING
1:19:00 16.7 TUE
No. Name Date Start Stop Mode
PDC
01 BBC 1 16/ 7 TUE 1:19 1:22 SP OFF
New Timer Programme
SELECT
CANCEL
ENTER RETURN
A line that is ready for programming is highlighted.
Press [ENTER] (10).
2
≥ The Timer Programme Correction screen appears.
TIMER
RECORDING
Name Date Start Stop
----------
---- --:-- -- --:-- --
Please set Channel.
No.
SELECT
--
0 9
ENTER RETURN
Use [1] (10) to move through the items and change
3
the items with [3, 4] (10).
≥ The current settings are shown each time you press [ 1 ]
(10).
≥ You may use the numeric buttons (4) to enter "Name",
"Date", "Start" and "Stop".
TIMER
RECORDING
Name Date Start Stop
BBC 1 16/ 7 TUE 2:00
1:00
≥ Name (Programme Position/TV Station Name)
≥ Date
Current date > the day before one month later >
Daily (Sunday to Saturday) > Daily (Monday to Saturday) >
Daily (Monday to Friday) > Weekly (Sundays) > ... >
Weekly (Saturdays)
≥ Start (start time)/Stop (finish time)
The time increases or decreases in 30-minute increments if
you hold the button.
≥ Mode (Recording mode)
XP > SP > LP > EP > FR (page 25)
≥ PDC (For the United Kingdom)
ON > OFF (
jjj ) (page 32)
Press [ENTER] (10) when you have finished making
4
changes.
≥ To continue programming:
Repeat steps 2, 3, and 4.
Press [PROG/CHECK] (13) or [RETURN] (23).
5
1:58 SP
Disc
space
OK
Remain 1:58 SP
1:55:00 16.7 TUE
Mode PDC
SP ---
Remain 1:58 SP
1:19:00 16.7 TUE
Mode PDC
SP OFF
To put the unit on recording standby
Press [ Á , TIMER] (12).
Ensure " Á " lights on the unit's display.
To change the timer recording programme
1) While the Timer Programme List Screen is being shown, use
[ 3 , 4 ] (10) to select the programme you want to change, and
press [ENTER] (10) to show the Timer Programme Correction
screen.
≥ You may also select programme by inputting a 2-digit
number using the numeric buttons (4).
≥ Use [ 2 , 1 ] (10) to move to the page preceding or following
the one on display.
2) Move through the items with [ 1 ] (10) and change the settings
with [ 3 , 4 ] (10) and press [ENTER] (10).
Note
≥ The built-in clock employs 24-hour system.
≥ The remaining time is not shown if you insert discs other than
DVD-RAM or DVD-R.
≥ The remaining time displayed is calculated based on the current
recording mode.
≥ If the disc is protected (pages 37, 73), the unit switches to
standby but does not go on standby for recording. Check the disc
carefully.
≥ Recording is not possible unless you set "Disc Protection" in
"DISC INFORMATION" to "Off" (page 37).
≥ You cannot record to a disc if the write protect tab on a cartridge
disc is set to protect. Release this before operation (page 73).
≥ Even if the unit is put in the timer recording standby mode or the
timer recording is being performed, you can play a programme.
≥ If the unit is not put in the timer recording standby mode at the
latest 10 minutes before the programmed timer recording starting
time, the [ Á ] flashes on the unit display. In this case, press the
[ Á , TIMER] (12) button to put the unit in the timer recording
standby mode.
≥ When recording more than one programme in a row, for DVD-
RAM the first few seconds, and for DVD-R about the first 30
seconds of all programmes from the second one onwards will not
be recorded.
33
Timer recording (continued)