Manual Programming - Panasonic Diga DMR-E51 Operating Instructions Manual

Manual programming

[RAM] [DVD-R]
Remote control only
You can set your own programming conditions (up to 16
programmes).
Preparation
≥Switch [DVD, TV] (15) to "DVD".
≥Ensure that this unit's clock is set correctly.
≥Insert a disc for recording (make sure there is enough room for
the programme you are going to record plus a little extra).
Press [PROG/CHECK] (13).
1
≥The Timer Programme List screen appears.
TIMER
Remain
RECORDING
1:19:00 12.7 TUE
No. Name Date Start Stop Mode
01 64 ABC 12/ 7 TUE 1:19 1:22 SP
New Timer Programme
SELECT
Press ENTER to store
new programme.
ENTER RETURN
A line that is ready for programming is highlighted.
Press [ENTER] (10).
2
≥The Timer Programme Correction screen appears.
TIMER
RECORDING
Date Start
Name
:
/
Please set Channel.
SELECT
No.
--
ENTER RETURN 0 9
Use [1] (10) to move through the items and change
3
the items with [3, 4] (10).
≥The current settings are shown each time you press [1]
(10).
≥You may use the numeric buttons (4) to enter "Name",
"Date", "Start" and "Stop".
TIMER
RECORDING
Name Date Start
64 ABC 12/ 7 TUE 1:00
≥Name (Programme Position/TV Station Name)
≥Date
Current date>the day before one month later>
Daily (Sunday to Saturday)>Daily (Monday to Saturday)>
Daily (Monday to Friday)>Weekly (Sundays)>...>
Weekly (Saturdays)
≥Start (start time)/Stop (finish time)
The time increases or decreases in 30-minute increments if
you hold the button.
≥Mode (Recording mode)
XP>SP>LP>EP>FR (page 19)
≥Title
Select "Title" and press [ENTER] (10), then refer to page 29
for entering title.
Press [ENTER] (10) when you have finished making
4
changes.
≥To continue programming:
Repeat steps 2, 3 and 4.
5 Press [PROG/CHECK] (13) or [RETURN] (23).
1:58 SP
Disc
space
OK
Remain 1:58 SP
1:55:00 12.7 TUE
Stop Mode
: SP
Title
Remain 1:58 SP
1:19:00 12.7 TUE
Stop Mode
2:00 SP
Title
To put the unit on recording standby
, TIMER] (12).
Press [
Ensure " " lights on the unit's display.
To change the timer recording programme
1) While the Timer Programme List Screen is being shown, use
[3, 4] (10) to select the programme you want to change, and
press [ENTER] (10) to show the Timer Programme Correction
screen.
≥You may also select programme by inputting a 2-digit number
using the numeric buttons (4).
≥Use [2, 1] (10) to move to the page preceding or following
the one on display.
2) Move through the items with [1] (10) and change the settings
with [3, 4] (10) and press [ENTER] (10).
Notes
≥The built-in clock employs 24-hour system.
≥The remaining time is not shown if you insert discs other than
DVD-RAM or DVD-R.
≥The remaining time displayed is calculated based on the current
recording mode.
≥If the disc is protected (pages 30 and 64), the unit switches to
standby but does not go on standby for recording. Check the disc
carefully.
≥Recording is not possible unless you set "Disc Protection" in
"DISC INFORMATION" to "Off". (page 30)
≥You cannot record to a disc if the write protect tab on a cartridge
disc is set to protect. Release this before operation (page 64).
≥Even if the unit is put in the timer recording standby mode or the
timer recording is being performed, you can play a programme.
≥When recording more than one programme in a row, for
DVD-RAM the first few seconds, and for DVD-R about the first
30 seconds of all programmes from the second one onwards will
not be recorded.
26
Timer recording (continued)