Download Print this page

Audiovox Prestige Platinum APS-350-A Installation Manual

Audiovox car security system installation manual
Hide thumbs Also See for Prestige Platinum APS-350-A:

Advertisement

Quick Links

Note : When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver's door pin switch in order
to begin the passive arming sequence.
RF Programmable Features :
Feature Selection
First
Second
Third
Fourth
Fifth
Sixth
Seventh
Eighth
To program these selectable features;
Action
Turn ignition on
Flip valet switch on then off 3 times
Within 3 seconds, turn ignition Off
First
Within 3 seconds, turn ignition On
Press transmitter button 1 to change
Second
Flip valet switch on then off
Press tranmitter button 1 to change
Third
Flip valet switch on then off
Press transmitter button 1 to change
Fourth
Flip valet switch on then off
Press transmitter button 1 to change
Fifth
Flip valet switch on then off
Press transmitter button 1 to change
Sixth
Flip valet switch on then off
Press transmitter button 1 to change
Seventh
Flip valet switch on then off
Press transmitter button 1 to change
Eighth
Flip Valet Switch on then off
Press transmitter button 1 to change
Flip valet switch on then off
Turn ignition key off
Note : Once you enter the feature programming mode, do not allow more than 15 seconds to pass between steps, or the
programming will be terminated.
SELECTABLE FEATURES
1 Chirp
1 Second Door Locks
Auto Lock On
Auto Unlock On
Passive Door Locks
Passive Arm
Voltage Sense
Horn Chirps On
Siren Chirps On
o r
o r
o r
o r
or
or
or
or
o r
2 Chirps
3.5 Second Door Locks
Auto Lock Off
Auto Unlock Off
Active Door Locks
Active Arm
Hardwire
Horn Chirps Off
Siren Chirps Off
System Response
No response
1 Chirp - LED 1 flash
Short chirp, then long chirp
1 chirp = 1 second door locks
2 chirps = 3.5 second door locks
2 chirps = auto locks off
1 chirp = auto locks on
2 chirps = auto unlock off
1 chirp = auto unlock on
1 chirp = passive locks
2 chirps = active locks
1 chirp = Passive Arm
2 chirps = Active Arm
1 chirp = Voltage sense on
2 chirps = Hardwire
1 chirp = Horn chirps on
2 chirps = Horn chirps off
1 chirp = Siren chirps on
2 chirps = Siren chirps off
Exit program mode
Exit program mode
Page 1
Model APS-350-A
Installation Manual
Default
1 Second
Auto Lock Off
Auto Unlock Off
Active Locks
Passive Arm
Hardwire On
Horn Chirps On
Siren Chirps On
LED Response
1 Flash Pause...
2 Flash Pause...
3 Flash Pause...
4 Flash Pause...
5 Flash Pause...
6 Flash Pause...
7 Flash Pause...
8 Flash Pause...

Advertisement

loading

Summary of Contents for Audiovox Prestige Platinum APS-350-A

  • Page 1 2 chirps = Horn chirps off 1 chirp = Siren chirps on 2 chirps = Siren chirps off Exit program mode Exit program mode Page 1 Model APS-350-A Installation Manual Default 1 Second Auto Lock Off Auto Unlock Off Active Locks...
  • Page 2 INSTALLATION OF MAJOR COMPONENTS Control Module : Select a mounting location inside the passenger compartment ( up behind the dash ), and secure using the two screws provided. The control module can also be secured in place using cable ties. Do not mount the control module in the engine compartment, as it is not waterproof.
  • Page 3: Wiring The System

    Note : This is a normally closed starter cut arrangement, and when power is removed from the security system, the starter disable feature will not operate, allowing the vehicle to start. Audiovox does not recommend using the Orange wire to interrupt anything but the start- ing circuit of the vehicle.
  • Page 4 2 Dark Green w/ White Trace Wires : ENTRY ILLUMINATION The dark green w/ white trace wires provide the entry lighting, and flash the vehicle’s dome light while the alarm is sounding. These are NO ( normally open ) and COM ( common ) contacts of an on board, 10 Amp maximum relay.
  • Page 5 Dark Green w/ Black Trace Wire : LATCHING OUTPUT / CHANNEL 3 The green w/ black trace wire latches to ground via an independent RF channel from the keychain transmit- ter. This is a transistorized, low current ( 300 mA ) output, and should only be used to drive an external relay coil.
  • Page 6: Completing The Installation

    Cut the existing unlock wire, and connect the white wire to the slave switch or motor side of the cut wire. Connect the blue wire to the master switch side of the cut wire. The orange and blue w/ white stripe wires must be connected to a fused + 12 VDC battery source. Refer to the door lock wiring supplement for proper connection of these wires into the various locking circuits available in current vehicles.
  • Page 7 Audiovox Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788 128-5082A...