Input Select - Panasonic BT-LH1700WE Operating Instructions Manual

Main Menu
(continued)

INPUT SELECT

Sub menu Settings
VIDEO / Y/C
<AUTO>
<NTSC>
<PAL>
NTSC SETUP
<75>
<00>
YP P /RGB
<YP
B R
<RGB-VIDEO>
<RGB-COMP.>
COMPONENT
<SMPTE>
LEVEL
<B75>
<B00>
RGB SYNC
<G-ON>
<EXT>
COMP.
*1 "AUTO" is set when the monitor is shipped from the factory, but if there are concerns about noise etc. from outside the
input signal, we recommend assigning specific format.
g COMP.
The following menus are switched by selecting "RGB-COMP." in "YP
Sub menu Settings
*1
AUTOSETUP
H POSITION
<0–60>
(Factory preset settings: 30)
V POSITION
<0–60>
(Factory preset settings: 30)
PHASE
<0–31>
(Factory preset settings:
CLOCK
<700–1800>
(Factory preset settings:
WXGA/XGA
<XGA>
<WXGA>
*1 "EXECUTING" is displayed while "AUTOSETUP" is being executed, and "COMPLETE" is displayed when
"AUTOSETUP" is completed.
If "AUTOSETUP" cannot be completed, "INCOMPLETE" is displayed.
*2 Each RGB-COMP. input compatible format can be adjusted.
Explanation
Used to select the input format for VIDEO and Y/C input.
<AUTO>
<NTSC>
Selects the NTSC setup level.
<75>
<00>
P > Selects either YP
B R
<YP
<RGB-VIDEO>Selects the video RGB signal.
<RGB-COMP .>Selects the PC RGB signal.
Selects YP
<SMPTE>
<B75>
<B00>
Selects the SYNC when using RGB-VIDEO input.
<G-ON>
<EXT>
Performs analog PC settings. (Refer to "COMP." below)
Explanation
Screen automatic adjustment is performed when "RGB-
COMP." is selected in "YP
menu. "AUTOSETUP" is performed if a different screen is
displayed, and "YES" is selected.
Used to adjust the picture display position in the horizontal
direction.
Used to adjust the picture display position in the vertical
direction.
Used to adjust the clock phase with 1/32 clock phases.
page E-21)
Used to adjust the sampling clock in dot units.
page E-21)
Switches between WXGA and XGA.
The underlined values are factory preset setting values.
Either NTSC or PAL is automatically selected.
NTSC
Select this when using with a setup signal of
7.5 IRE. (The inner parts of the monitor are set
to the 7.5 IRE setup level to suit the black level)
Select this when there is no setup level signal.
P (Component) or RGB input mode.
B R
P > Selects the YP
B R B
P (Component) signal input level.
B R
When the signal level specified in SMPTE is
Chroma 100 IRE P
Select this when connecting a betacam or
simliar devices set to 7.5 IRE. (The inner parts
of the monitor are set at 7.5 IRE setup level to
suit the black level)
Select this when connecting a betacam or similar
devices that are not setup to the IRE level.
Select when a synchronizing signal is
superimposed on the G signal.
Select when an external synchronizing signal is
received in synchronization.
P /RGB" in the "INPUT SELECT" menu.
B R
The underlined values are factory preset setting values.
P /RGB" in the "INPUT SELECT"
B R
*2
*2
<PAL> PAL
P signal.
R
, P = 0.7 Vp-p.
B R
*2
*1
*2
E-20