FOR-A USF-1053DDA Operation Manual
  1. Manuals
  2. Brands
  3. FOR-A Manuals
  4. Amplifier
  5. USF-1053DDA
  6. Operation manual
FOR-A USF-1053DDA Operation Manual

FOR-A USF-1053DDA Operation Manual

Hide thumbs Also See for USF-1053DDA:
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATION
MANUAL
USF-1053DDA
Digital Distribution Amplifier
Edition – Rev. 1
nd
2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the USF-1053DDA and is the answer not in the manual?

Questions and answers

Related Manuals for FOR-A USF-1053DDA

Summary of Contents for FOR-A USF-1053DDA

  • Page 1 OPERATION MANUAL USF-1053DDA Digital Distribution Amplifier Edition – Rev. 1...
  • Page 2 Precautions [Power] Operate unit only at the specified supply voltage. Caution Disconnect the power cord via the power plug only. Do not pull on the cable portion. Do not place or drop heavy or sharp-edged objects on the power cord. A damaged cord can cause fire or electrical shock hazards.
  • Page 3 [Circuitry Access] Do not remove covers, panels, casing, or access the circuitry with power applied to the unit. Turn the power off and disconnect the power cord prior to removal. Internal servicing / adjustment of unit should only be performed by qualified personnel. Do not touch any parts / circuitry with a high heat factor.
  • Page 4 Upon Receipt Unpacking Congratulations! By purchasing a USF-1053DDA Digital Distribution Amplifier, you have entered the world of FOR-A and its many innovative products. Check your received items against the packing list below. Check to ensure no damage has occurred during shipment. If damage has occurred, or items are missing, inform your supplier immediately.

  • Page 5: Table Of Contents

    2-1. Front Panel ........................... 7 2-2. Rear Panel ........................... 7 3. DIP Switch Settings ........................8 4. USF-1053DDA Input and Output via Internal Bus ..............10 4-1. Input Choice Example Using the Internal Bus ..............10 4-1-1. Source Settings via DIP Switch .................. 10 4-1-2.

  • Page 6: Product Overview

    1. Product Overview 1-1. Overview The USF-1053DDA is a multi-bit rate video distribution amplifier that can be installed in a USF frame. The USF-1053DDA supports 3G-SDI, HD-SDI, SD-SDI, and DVB-ASI, and is capable of producing up to 5 outputs from 1 input.

  • Page 7: Panel Descriptions

    *1 When video signal from internal bus of USF-212/212S is distributed, video signal bit rate detection is not available. All the LEDs; 270Mb/s, 1.5Gb/s, and 3.0Gb/s are turned off. Refer to Sec.4 “USF-1053DDA Input and Output via Internal Bus” for switching the video signal source.

  • Page 8: Dip Switch Settings

    *1: The switch is set suitable for the main unit when shipped out from our factory. IMPORTANT SW Nos. 5 to 8 are factory use only. Do not change these settings. Table 1: Input Signal Switch Settings Slot: USF frame slot no. into which USF-1053DDA is installed. Slot Signal Distribution Set by Web GUI.
  • Page 9  In case a distributing signal is set to another slot, be sure to install a module in the designated slot.  In case SW1 to SW4 are set to other than those described in Table 1: Input Signal Switching Settings, USF-1053DDA will distribute its input.

  • Page 10: Usf-1053Dda Input And Output Via Internal Bus

    Internal Input USF-1053DDA modules can send and receive one SDI input channel via internal bus on the USF frame. To configure two USF-1053DDA modules and feed an input from another USF-1053DDA, install module pairs according to the figure shown above (e.g., into Slot 1 and Slot 2.). If paired with another type of USF module, for instance a USF-1043FS, the USF-1043FS can be installed in any slot, from Slots 1 to 4.

  • Page 11: Source Settings Via Web Gui

    USF-1053DDA 4-2-1. DIP Switch Settings (1) Set the DIP switch settings to those shown in the table below for the USF-1053DDA to be installed into Slot 1 of the USF frame. (2) Set the DIP switch settings to those shown in the table below for another USF-1053DDA to be installed into Slot 2 of the USF frame.

  • Page 12: Web Gui

    To simultaneously monitor a USF-1053DDA from multiple PCs, use the SNMP function. 5-1. Web Display Information Start the Web GUI and click on a USF-1053DDA from Slot 1 to 12 of USF-212S to open the window as shown below. Module Information...

  • Page 13: Syslog Functions

    (3) FORA-USF1053DDA-MIB.zip File is downloaded. (4) Unzip the file and load it into your SNMP manager. 5-2. syslog Functions The USF-1053DDA supports log monitoring and message transmission via syslog protocol. Clicking the syslog tab opens a window shown as below. Item...

  • Page 14: About Snmp

    6. About SNMP The USF-1053DDA can be remotely monitored using an external SNMP monitoring system that supports SNMPv2C. MIB (Management Information Base) files that are required for SNMP monitoring systems can be downloaded from the Web GUI. Refer to the prior section for details on downloading MIB files.

  • Page 15: Specifications And Dimensions

    7. Specifications and Dimensions 7-1. Specifications Video Input 3G-SDI: 3Gbps HD-SDI: 1.5Gbps SD-SDI: 270Mbps DVB-ASI: 270Mbps 75Ω BNC x 1 Video Output 3G-SDI: 3Gbps HD-SDI: 1.5Gbps SD-SDI: 270Mbps DVB-ASI: 270Mbps 75Ω BNC x 5 Cable Compensation Automatic Cable Compensation 3G-SDI: Max. 70m (Using 5C-FB-equivalent cable) HD-SDI: Max.100m (Using 5C-FB-equivalent cable) SD-SDI: Max.

Table of Contents