Advertisement

Quick Links

Debonaire DUPLO 1200-1600-2000-2400-2800
Promina Board
Cladding
Non-Combustible
Burner
Hearth
Fire and flue system installation, and instructions to comply with NZS 5601.1:2013,
3645.1(Int):2010, 3645.2(Int):2010, 5266:2014, 2918:2001.
The fireplace is constructed and tested to comply with NZS 4558(int):2013 "Decorative gas log and other fuel effect appliances".
Keep these instructions for further reference. Ensure that you have the correct and current installation details for the Warmington fireplace.
The Warmington unit is to be installed by a certified Warmington installer or an approved NZHHA installation technician.
A licenced certified gas fitter and licenced electrician are required to run power and gas supplies as required to the unit and any commissioning as part of the installation
process.The heater must be installed according to these instructions and in compliance with all relevant building, gas fitting, electrical and other statutory regulations.
Read all the instructions carefully before commencing the Installation. Failure to follow these instructions may result in a fire hazard and void the warranty
Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification.
1
Custom Fire DUPLO — Gas Burner

Installation Instructions

Related documents
See www.homeheat.co.nz/members for a certified NZHHA SFAIT Installer in your area.
All Dimension are in mm.............Copyright ©
Flue
Liner
Installation
IMPORTANT
12 September 2016
Firebox
Venting
NOTE: T.V. Option Available
Additional Costing for T.V Above Fire-
Consult your nearest Warmington Agent
Visit: www.warmington.co.nz
For Specification
Venting Base Burner

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Debonaire DUPLO 1200 and is the answer not in the manual?

Questions and answers

Summary of Contents for Warmington Debonaire DUPLO 1200

  • Page 1: Installation Instructions

    The fireplace is constructed and tested to comply with NZS 4558(int):2013 “Decorative gas log and other fuel effect appliances”. Keep these instructions for further reference. Ensure that you have the correct and current installation details for the Warmington fireplace. Installation The Warmington unit is to be installed by a certified Warmington installer or an approved NZHHA installation technician.
  • Page 2 This will ensure that the draft in the flue system is always to the outside. “CAITEC AIR” the limits and requirements. See details in these Spec’s, on www.warmington.co.nz or contact your local Agent. Wind Noise: You may encounter wind noise in some installations.
  • Page 3 Seismic restraint Secure firebox through anchor positions through Base & through bracket at Top of Fire Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 4: Minimum Alcove Clearances

    Timber Opening Opening Height 1850 1850 1850 1850 1850 Opening Width 1223 1623 2023 2423 2823 Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 5: Important Note

    This Cavity Air Must Not be Vented to the Burner Cavity Cavity Venting Only Burner Base Venting Only Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 6: Firebox Installation

    Aluminum Foil Duct NOT SUPPLIED Vent NOT SUPPLIED Note: Hearth to be Constructed as Per Specification Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 7 Warm Air & Cavity Venting Vent & Duct NOT SUPPLIED Note: Hearth Details Not Shown see Page 5 Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 8: Minimum Flue Height

    25mm gap around the Liner with a “Venting Flashing Cone-Spider” can be used. Ref : to Figures …… In this Specification Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 9 Vermin and Rodent proof. Test Report Number Date of Report 04/1039 July 2004 04/1040 July 2004 04/1041 July 2004 Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 10 “Insulation under under flashing” flashing” VENTING THROUGH FLASHING Note : 2 X 100MM VENTS in chase. Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 11 FRAME OUT AND TRIM OUT DETAILS FOR CHIMNEY CHASE Option X – Singled Lined Flue System Option Y – Double Lined Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 12 Additional Costing for T.V Above Fire- Consult your nearest Warmington Agent Visit: www.warmington.co.nz For Specification Minimum requirement for floor protector Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 13: General Notes

    № of Injectors / Size of Jet Size of Jet Date Manufactured Serial Numbers CUB – 0 Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 14 FLUED GAS APPLIANCES All Gas Fires r equir ing War mington Flue Systems shall be Installed to the requirements of the cur r ent standards and shall be appropriately designed and constructed to permit safe and effective use. This Appliance must be flued to the outside atmosphere. All Warmington Fires must be Installed with a minimum of 3.6m of Approved Warmington Gas Flue and Liners.
  • Page 15 Fit Burner Grate by sliding R & L Side Metal Pins on Grate, into Holes Located on Burner Side Plates , as shown below . 1200 1600 2000 2400 2800 Number of Coals Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 16 Replace the Base screw and check for leaks. 3 Flame Pilot in Assembled State Correct Operation of 3 Flame Pilot Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 17 POINTS OF SAFTEY—To the Customer /Home-Owner Your Warmington Gas Decorative Fire operates on the principle of dual radiant and convected heat. Therefore it is important to observe the following precautions associated with any heating appliance or open fire.
  • Page 18: To Shut Down

    Instructions and Specifications, or is the subject to damage or misuse beyond the expected conditions of normal use which could result in injury or property damage. Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 19: Fault Finding

    Note: If unit is fitted with an LED, the LED will light up on a flame failure. The cycle from starting to ignition is approx 30 seconds. Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 20: Warranty

    As part of the manufacturing process, these units have been fully factory tested for correct ignition and fault finding purposes to insure they run correctly before being packaged. Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 21 MAIN & HI / LOW SWITCH CONNECTION HT Leads White Lead – Spark Red Lead - Rectifier Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 22 WARNING: To ensur e the Cor r ect Oper ation of the Modulator it is necessar y that the Plastic Cap is r etur ned to its original location . Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 23  Replace the Base screw and check for leaks. 3 Flame Pilot in Correct Operation Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 24 Access to Gas Test Point Place Burner on top of Heat Shield and Angles Gas Test Point under Burner Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 25 12 September 2016 GAS STARTER SCHEMATIC DIAGRAM Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...
  • Page 26: Maintenance Guidelines

    NOTE: Keep a copy of these instructions for operating and maintenance guidelines. Industries 1994 LTD PO Box 58652, Botany 2163, Auckland www.warmington.co.nz Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification. All Dimension are in mm………….Copyright ©...

Table of Contents