Lionel 419R Owner's Manual
  1. Manuals
  2. Brands
  3. Lionel Manuals
  4. Toy
  5. 419R
  6. Owner's manual
Lionel 419R Owner's Manual

Lionel 419R Owner's Manual

Heliport
Hide thumbs
Table of Contents

Advertisement

Quick Links

71-4084-250
8/01
Lionel
419R Heliport
Owner's Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 419R and is the answer not in the manual?

Questions and answers

Related Manuals for Lionel 419R

Summary of Contents for Lionel 419R

  • Page 1 71-4084-250 8/01 Lionel 419R Heliport Owner’s Manual...
  • Page 2 Congratulations ongratulations on your purchase of the The Lionel Heliport is perfect for any classic Lionel Heliport! This accessory O-27 or O gauge three-rail layout with features a durable, detail molded structure 12-18 volts (AC) available. with interior illumination and a launching helicopter that will provide a lifetime of high-flying action.

  • Page 3: Table Of Contents

    Installing your Lionel Heliport Launching your helicopter Replacing the lamp in your Lionel Heliport Limited Warranty/Lionel Service The following Lionel marks may be used throughout this instruction manual and are protected under law. All rights reserved. Lionel ® , TrainMaster ®...

  • Page 4: Wiring Your Lionel Heliport For Conventional (Non-Command) Operation

    Wiring your Lionel Heliport for conventional (non-Command) operation o operate properly, your Heliport requires clip, and gently tug on the wire to be 12-18 volts (AC). You can supply power sure that you have a good connection. to this accessory in two ways: wiring directly 2.
  • Page 5 Wiring your Lionel Heliport for conventional (non-Command) operation (Continued) Figure 1. Wiring for conventional operation...

  • Page 6: Operating Your Accessory In Conventional (Non-Command) Mode

    5. Attach another wire to the SC-1 unit’s TrainMaster Command Control environ- AUX1, position 1 (or next available posi- ment. To wire your Lionel Heliport with an tion) terminal. SC-1, follow these steps. Figure 2 illustrates 6. Connect this wire to one of the spring the following procedure.

  • Page 7: Wiring Your Heliport With An Sc-2 For Trainmaster Command Control Operation

    5. Attach another wire to the SC-2 unit’s TrainMaster Command Control environ- ACC1, momentary position 1 (or next ment. To wire your Lionel Heliport with an available position). SC-2 (part no. 6-22980), follow these steps. 6. Connect this wire to one of the spring Figure 3 illustrates the following procedure.

  • Page 8: Operating Your Heliport With Trainmaster Command Control

    ID# of 1. Remote Controller is easy! Begin by 6. Press SET on the CAB-1 remote. assigning an ID# to your Lionel Heliport. 7. Slide the PGM/RUN switch back to RUN. 1. Be sure that the Command Base is ON.

  • Page 9: Installing Your Lionel Heliport

    Installing your Lionel Heliport fter you have completed the wiring of Attach the two radar dishes to the post this accessory, your Lionel Heliport is and push the base of the post into the clear for landing on your layout! opening on the roof.

  • Page 10: Launching Your Helicopter

    Launching your helicopter The Heliport is wired, positioned, and The notches or teeth in the center Note! assembled. You are clear for takeoff! of the platform and at the bottom Here are your flight instructions. of the helicopter must fit together. Rotate the helicopter blades while the helicopter is 1.

  • Page 11: Replacing The Lamp In Your Lionel Heliport

    Replacing the lamp in your Lionel Heliport The interior of your Lionel Heliport is illu- 2 Locate the lamp and pull it out of the minated by one lamp (part no. 12-3011-311). socket. Refer to the diagram for lamp During the course of normal operation, it may location.

  • Page 12: Limited Warranty/Lionel Service

    Center, together with proof of original purchase above instructions carefully before returning any will, at the option of Lionel L.L.C., be repaired or merchandise for service. You may choose to have replaced, without charge for parts or labor. In the...

Table of Contents