JRC JMA-5212-4 Simplified Manual
Hide thumbs
Also See for JMA-5212-4:
- Installation manual (156 pages) ,
- Instruction manual (540 pages) ,
- User manual (494 pages)
Table of Contents
Advertisement
Quick Links
JMA-5212-4/6
JMA-5222-7/9
JMA-5212-4HS/6HS
SIMPLIFIED MANUAL
1
INTRODUCTION ..................................................................................................S-1
1.1
READ ME ....................................................................................................S-1
2
BASIC OPERATION.............................................................................................S-2
2.1
POWER ON AND START THE SYSTEM....................................................S-2
2.2
END THE OPERATION AND POWER OFF................................................S-3
2.3
ADJUST MONITOR BRILLIANCE [BRILL]................................................S-3
2.4
CHANGE OBSERVATION RANGE [RANGE + / - ] ....................................S-4
2.5
ADJUST GAIN [GAIN / PL] ........................................................................S-4
2.6
SUPPRESS SEA CLUTTER [AUTO-SEA] .................................................S-4
2.7
SUPPRESS RAIN / SNOW CLUTTER [AUTO-RAIN] ................................S-6
2.8
USING ELECTRONIC BEARING LINE (EBL1 / EBL2)..............................S-7
2.9
USING VARIABLE RANGE MARKER (VRM1 / VRM2) ...........................S-10
2.10
2.11
SWITCH AZIMUTH DISPLAY MODE [AZI MODE] ................................. S-11
2.12
2.13
3
TARGET TRACKING OPERATION ...................................................................S-14
3.1
ACQUIRING TARGET [ACQ] ...................................................................S-14
3.2
DISPLAY TRACKED TARGET DATA [TGT DATA] ..................................S-14
3.3
4
AIS OPERATION................................................................................................S-16
4.1
SETTING AIS DISPLAY FUNCTION (AIS FUNCTION) ............................S-16
4.2
ACTIVATE AIS TARGETS (ACT AIS) .......................................................S-16
4.3
4.4
DEACTIVATE AIS TARGETS (DEACT AIS) .............................................S-18
5
TARGET TRACKING / AIS COMMON OPERATION .........................................S-19
5.1
SETTING VECTORS (VECTOR)...............................................................S-19
5.2
SETTING COLLISION DECISION CRITERIA (CPA / TCPA LIMIT) .........S-20
6
OTHER CONTENTS ..........................................................................................S-21
6.1
RESET ALARM BUZZER [ALARM ACK] ................................................S-21
6.2
OPERATION ON NUMERIC VALUE INPUT MENU .................................S-21
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for JRC JMA-5212-4
Summary of Contents for JRC JMA-5212-4
-
Page 1: Table Of Contents
JMA-5212-4/6 JMA-5222-7/9 JMA-5212-4HS/6HS SIMPLIFIED MANUAL INTRODUCTION ....................S-1 READ ME ....................S-1 BASIC OPERATION.....................S-2 POWER ON AND START THE SYSTEM............S-2 END THE OPERATION AND POWER OFF..........S-3 ADJUST MONITOR BRILLIANCE [BRILL]..........S-3 CHANGE OBSERVATION RANGE [RANGE + / - ] ........S-4 ADJUST GAIN [GAIN / PL] ................S-4 SUPPRESS SEA CLUTTER [AUTO-SEA] ..........S-4... -
Page 3: Introduction
INTRODUCTION Read Me About this manual See the INSTRUCTION MANUAL for details. Maintain this SIMPLIFIED MANUAL so that operators can refer to it at anytime. About radar equipment Use the radar only as a navigation aid. The final navigation decision must always be made by the operator him/herself. -
Page 4: Basic Operation
Simplified Manual BASIC OPERATION Power ON and Start the System Procedures 1 Check that the ship’s mains are turned on. 2 Press the [STBY] key. The system is turned on, and the preheating time is displayed. Preheat is indicated upper left of the display. 3 Wait until the preheating time is over. -
Page 5: End The Operation And Power Off
End the Operation and Power Off Exit 1 Press the [STBY] key. The radar will stop transmission and the antenna will stop rotating. Transmit upper left of the display changes to Standby . 2 Press the [STBY] key and the [TX / PRF] key together. The system will be turned off. -
Page 6: Change Observation Range [Range
Simplified Manual Change Observation Range [RANGE + / - ] Procedures 1 When increasing the observation range, press the [RANGE+] key. Increasing the observation range will enable a wider range to be observed. 2 When decreasing the observation range, press the [RANGE-] key. Decreasing the observation range will enable a narrower range to be observed. - Page 7 Using the automatic sea clutter suppression mode Procedures 1 Press the [AUTO-SEA] dial. The automatic sea clutter suppression mode is selected, and AUTO is displayed in sea clutter suppression (Sea) mode switching. 2 Make adjustments by turning the [AUTO-SEA] dial. Even when the automatic sea clutter suppression mode is selected, turning the [AUTO-SEA] dial can make fine adjustments manually.
-
Page 8: Suppress Rain / Snow Clutter [Auto-Rain
Simplified Manual Suppress Rain / Snow Clutter [AUTO-RAIN] Using the manual rain / snow clutter suppression mode Procedures 1 Turning the [AUTO-RAIN] dial. The rain / snow clutter suppression function suppress rain / snow clutter returns by decreasing the receiving gain. Since the rain / snow clutter suppression function also has the effect of suppressing sea clutter, the suppression efficiency improves when the [AUTO-RAIN] dial is used with the [AUTO-SEA] dial. -
Page 9: Using Electronic Bearing Line (Ebl1 / Ebl2
Cancellation 1 Press the [RAIN] dial. The automatic rain / snow clutter suppression mode is cancelled, and AUTO is changed to in the sea clutter suppression (Sea) mode field and the rain / snow clutter suppression (Rain) mode field. Using Electronic Bearing Line (EBL1 / EBL2) [I] Operating EBL (EBL) Procedures 1 Press the [EBL1] or [EBL2] key. - Page 10 Simplified Manual Cancellation 1 Press the [EBL1] or [EBL2] key again. The selected EBL display will disappear. [II] Moving the Starting Point of EBL The system provides three types of EBL starting points. Select one of them in accordance with purpose.
- Page 11 5 Put the cursor on the EBL starting point is to be moved, and press the [ENT] key. The selected EBL starting point will be determined. To return the EBL starting point to own ship's position Procedures 1 Hold down [EBL] control. The Jog Dial Button Mode will appear 2 Select 2 Floating EBL using Left Jog Dial, and set Floating EBL for Left Jog Dial Mode.
-
Page 12: Using Variable Range Marker (Vrm1 / Vrm2
Simplified Manual Using Variable Range Marker (VRM1 / VRM2) To operate VRM Procedures 1 Press the [VRM1] or [VRM2] key. The VRM adjustment will be highlighted, and the selected VRM becomes operable. 2 Turn the [VRM] dial. To turn the [VRM] dial to the right, the VRM control wide, to turn the [VRM] dial to the left, the VRM control narrow. -
Page 13: Switch Transmitter Pulse Length [Gain / Pl]
2.10 Switch Transmitter Pulse Length [GAIN / PL] Procedures 1 Press the [GAIN / PL] dial. The selected pulse length will be displayed in the pulse length indication. 2.11 Switch Azimuth Display Mode [AZI MODE] Procedures 1 Press the [AZI MODE] key. The azimuth display modes are switched. -
Page 14: Switch True / Relative Motion Display Mode [Tm / Rm]
Simplified Manual 2.12 Switch True / Relative Motion Display Mode [TM / RM] Switching Motion Display Mode Procedures 1 Press the [TM / RM] key. The motion display mode are switched. Resetting Own Ship to its Initial Position in True Motion (TM) Mode Procedures 1 Press the [TM / RM] key for 2 seconds. -
Page 15: Display Radar Trails [Trails]
2.13 Display Radar Trails [TRAILS] Changing the length of the trail Procedures 1 Press the [TRAILS] key. Values of the length of the radar trail are switched. Erasing Trails Data Procedures 1 Press the [TRAILS] key for 5 seconds. All the saved trails data will be erased. The system starts plotting trails in initial state. If [TRAILS] key is pressed for 2 seconds, the RADAR Trails Setting menu is opened. -
Page 16: Target Tracking Operation
Simplified Manual TARGET TRACKING OPERATION Acquiring Target [ACQ] Procedures 1 Put the cursor on the target to be acquired, and press the [ACQ] key. The target will be acquired and the initial acquisition symbol will be displayed. The vector will be displayed within one minute. -
Page 17: Canceling Tracked Targets [Tgt Cncl]
Canceling Tracked Targets [TGT CNCL] Canceling targets one by one [TGT CNCL] Procedures 1 Put the cursor on the tracked target to the desired for canceling target, and press the [TGT CNCL] key. The vectors and symbols of the tracked targets will disappear, and only the radar video remain. Canceling all targets collectively [TGT CNCL] Procedures 1 Press the [TGT CNCL] key for 5 seconds. -
Page 18: Ais Operation
Simplified Manual AIS OPERATION Setting AIS Display Function (AIS Function) Procedures 1 Put the cursor on the AIS On / Off AIS , and press the [ENT] key. The received AIS information will be shown on the radar display. Activate AIS Targets (ACT AIS) Procedures 1 Set the cursor mode to ACT AIS. -
Page 19: Display Activated Ais Target Data[Tgt Data]
2 Put the cursor on the AIS target to be activated, and press the [ENT] key. The selected AIS target will be activated. Display Activated AIS Target Data[TGT DATA] Procedures 1 Put the cursor on the AIS target of which data is to be displayed, and press the [TGT DATA] key. -
Page 20: Deactivate Ais Targets (Deact Ais
Simplified Manual Deactivate AIS Targets (DEACT AIS) Procedures 1 Set the cursor mode to ACT AIS. The cursor mode will appear as ACT AIS. 2 Put the cursor on the activated AIS target to be deactivated, and press the [CLR/INFO] key. The selected AIS target will be deactivated. -
Page 21: Target Tracking / Ais Common Operation
TARGET TRACKING / AIS COMMON OPERATION Setting Vectors (Vector) Setting vector mode [VECT R / T] Procedures 1 Press the [VECT R / T] key. The current vector mode T (true vector) or R (relative vector) will be displayed in the target vector display true / relative switching. -
Page 22: Setting Collision Decision Criteria (Cpa / Tcpa Limit
Simplified Manual Setting Collision Decision Criteria (CPA / TCPA limit) Input of CPA Limit Procedures 1 Put the cursor on the CPA limit setting, and press the [ENT] key. The CPA Limit value input screen will appear. 2 Enter the value to be set as a CPA limit. For how to input numeric data on the numeric value input menu, see Section 6.2. -
Page 23: Other Contents
OTHER CONTENTS Reset Alarm Buzzer [ALARM ACK] Procedures 1 Press the [ALARM ACK] key. The alarm will stop buzzing. Operation on Numeric Value Input menu Procedures 1 Put the cursor on the numeric button to the desired value, and press the [ENT] key. - Page 28 For further information,contact: Not use the asbestos http://www.jrc.co.jp Marine Service Department Telephone : +81-3-3492-1305 Facsimile : +81-3-3779-1420 e-mail : tmsc@jrc.co.jp AMSTERDAM Branch Telephone : +31-20-658-0750 Facsimile : +31-20-658-0755 e-mail : service@jrcams.nl SEATTLE Branch Telephone : +1-206-654-5644 Facsimile : +1-206-654-7030 e-mail : service@jrcamerica.com...
Need help?
Do you have a question about the JMA-5212-4 and is the answer not in the manual?
Questions and answers