Panasonic CF-R1 SERIES Operating Instructions Manual page 25

9
This screen should
appear.
Select
a number
1
.
Restore
the
whole
HOD
to factory default
2.
Restore
Windows(R) 2000
Professional to the
first
partition
3.
End
Select a numt)er
1.
Restore the
whole
HDD
to factory default
2.
Restore
Windows(R)
XP
Professional to the
first
partition
3.
End
10
Make
a selection
from
the
menu.
To
restore
all
contents of the
hard
disk
to
factory de-
fault,
including the partition
setting($):
Select
[1
.
Restore the
whole
HDD
to factory default].
To
reinstall
Windows
2000/Windows
XP
to the
first
par-
tition to
factory default:
Select
[2.
Restore
Windows(R) 2000
Professional (or
Windows(R)
XP
Professional)
to the
first
partition].
In
such
cases,
the
initial
partition
size
must be
6
GB
or
more
of the
hard
disk
size.
Reinstallation
cannot be performed with a
small
partition
size.
1 1
At
the confirmation
message,
press
C
Y
]
.
The
computer
will reboot,
and
the
operations of
reinstal-
lation for the
hard disk
start automatically.
(The opera-
tions take
about
30-40
minutes.)
When
the
message
"insert the next
CD"
is
displayed,
insert
the
Product
Recovery
CD-ROM
showing
the
next
number
in the
sequence,
and
then
select
[OK].
(In
the case of
Windows
2000, only Product
Recovery
CD-
ROMs
1
to
3
can be
used.)
Xnote>
If
the
message "The media does
not contain the correct
file"
appears, select [OK].
The
message
"insert the next
CD"
will
be displayed
again.
Confirm
that the
proper Product
Recovery
CD-ROM
has
been inserted
by opening
the tray
of
the
CD
drive and
then close the
tray,
then select
[OK].
12 After the
reinstallation
procedure completes,
press
C
Enter
)
.
The
computer
will
be shut down.
<Only
when
using the
CD
drive Panasonic
KXL-
RW10A>
Remove
the
FIRSTAID
FD.
13
Remove
the
CD
drive,
and
then turn the
computer
on.
14
When
the
m
essage
[Press
F2
to enter
SETUP]
is
displayed,
press
(
F2
]
and
then run the Setup
Utility.
If
the
password
has
been
set,
enter the Supervisor
Pass-
word.
f
5
Press
Cfd)
.
At
the
co nfirmation message,
select [Yes]
and
press
(
Enter
3
.
(The Setup
Utility settings will return to their
default values.
Even
the security settings with
the
excep-
tion
of
the password(s)
will return to
their
default values.)
Chan
ge
the
s
ettings
where
necessary.
76
Press
CeTD
At
the co nfirmation message,
select [Yes]
and
press
(Enter)
.
7
7
Perform
the
setup procedure
for
Windows
by
following
the
instructions
on
the screen.
(Q^ page
1 1)
note}-
When
the
FIRSTAID
FD
is
to be created, follow the
steps in the
readme.txt on
the disk.
((^
page
1 2)
iWinclowsF200'0l
<When
using a
PC
Card-compatible
CD
drive other than
the
Panasonic
KXL-RW10A>
Copy
the
necessary
drivers,
from
the floppy
disk included
with your
CD
drive, to the
FIRSTAID
FD
with
the
method
below.
It
will
be
necessary
to edit the
CONFIG.SYS
file
and
AUTOEXEC.BAT
file
on
the
FIRSTAID
FD.
When
editing the
AUTOEXEC.BAT
file,
some
CD
drives require
card
managers
(card and
socket
service).
See
the
manual
included with your
CD
drive
for further
details.
®
Start
Window
s
and
insert
the
FIRSTAID
FD.
Select
[Start] -
[Programs]
-
[Acces-
sories]
-
[Notepad]
- [File] -
[Open],
input [a:\config.sys], then
select
[Open].
Select
[start]
- [All
Programs]
-
[Ac-
cessories] -
[Notepad]
- [File]
- [Open],
input [a:\config.sys], then
select
[Open].
Rewrite
the following
line
and
save.
Delete the following four
lines.
;KXL-RW10A
DRIVER
DEVICE=A:\TOOLS\KMASMGRA.SYS
DEVICE=A:\TO0LS\KMASASPA.SYS
DEVICE=A:\TOOLS\KMASCDA.SYS
/D:MSCD0OO
Add
the driver of your
CD
drive.
Device=A:
\pRlVHRl.SYS /D:MSCDOOO
'-Rewrite
this
driver for the driver
of your
CD
drive.
The
driver for the
PC
Card
will
also
be
necessary. Refer
to
the operation
manual
that
accompanies
the
CD
drive.
Save
the
file
and
close
[Notepad],
(?)
Copy
the
CD
driver
file (i.e.,
the driver
file
rewritten
in
step
©)
of
the
CD-ROM
drive
below
[a:\]
of
the
FIRSTAID
FD.
©
Set the
floppy disk
to the write-protect
stale.
After
this,
follow
the reinstalling
procedure of <Oiily
when
using
the
CD
drive Panasonic
KXL-RW10A>.
(Q- page
24)
25