Panasonic CF-R1 SERIES Operating Instructions Manual page 19

List
of Error
Codes
The
following
is
a
list
of
the
messages
that
BIOS can
display.
Most of
them occur during POST.
Some
of
them
display informa-
tion
about a
hanJware device, e.g.,
the
amount
of
memory
installed.
Others
may
indicate
a
problem
with a device, such as the
way
it
has been configured.
Following the
list
are
explanations of
the
messages and remedies
for
reported
problems.
If
your system displays
any
of the
below
error
messages other
that
the
ones
marked
with an asterisk
(*),
write
down
the
message
and contact
Panasonic Technical Support.
If
your system
fails after
you make
changes
in the
Setup menus,
reset
the
computer,
enter
Setup and
install
Setup defaults
or correct the error.
0200 Failure Fixed
Disk
Fixed disk
in
not
working or not
configured properly.
Check
to see
if
fixed disk
is
attached properly.
Run
Setup.
Find
out
if
the fixed-di.sk
type
is
correctly identified.
0210 Stuck
key
Stuck key on keyboard.
0211
Keyboard error
Keyboard
not
working.
0212 Keyboard Controller Failed
Keyboard controller failed
test.
May
require replacing
keyboard
controller.
0213 Keyboard locked
-
Unlock key switch
Unlock the
system
to
proceed.
0230 System
RAM
Failed at offset
:
nnnn
System
RAM
failed at offset
nnnn
of the
64k block
at
which
the error
was
detected.
0231
Shadow
RAM
Failed at offset
;
nnnn
Shadow
RAM
failed
at
offset
nnnn of the
64k block
at
which
the error
was
detected,
0232 Extended
RAM
Failed at offset
:
nnnn
Extended
memory
not
working or not configured properly
at
offset
mnn.
0250
System battery
is
dead
-
Replace
and run
SETUP
The
CMOS
clock battery indicator
shows
the battery
is
dead.
Replace the battery
and run Setup
to
reconfigure the system.
*0251
System
CMOS
ciiecksum
bad
•
Default configuration used
System
CMOS
has been
corrupted or modified incorrectly,
perhaps
by
an
application
program
that
changes
data stored in
CMOS.
The
BIOS
installed
Default
SETUP
Values.
If
you do not
want
these values, enter
Setup
and
enter
your
own
values.
If
the error
persists,
check
the
system battery
or contact
Panasonic Technical Support.
,
0260
System
timer error
The timer test failed.
Requires
repair
of system board.
0270 Real time
clock error
Real-time clock
fails
BIOS
test.
May
require
board
repair.
0280
Previous boot incomplete
-
Default configuration
used
Previous
POST
did
not
complete successfully.
POST
loads default values
and
offers to
run
Setup. If
the failure
was caused by
incorrect
values and they
are not corrected, the next boot will likely
fail,
On
systems with
control
of wait
states,
improper Setup
settings
can also
terminate
POST
and
cau.se this
error
on the next boot.
Run
Setup and
verify that the wait-state
configuration
is
correct.
This
error
is
cleared the
next time
the
system
is
booted.
0281
Memory
Size
found by
POST
differed
from
EISA
CMOS
Memory
size
found
by
POST
differed
from
EISA
CMOS.
02B0
Diskette drive
A
error
02B1
Diskette drive
B
error
Drive A: or B:
is
present but
fails
the
BIOS
POST
diskette tests.
Check
to see that
the drive
is
defined with the proper diskette
type
in
Setup
and
that
the diskette
drive
is
attached correctly.
02B2
Incorrect
Drive
A
type
-
run
SETUP
Type of
floppy drive A:
not correctly
identified in
Setup.
02B3
Incorrect
Drive
B
type
-
run
SETUP
Type
of floppy drive
B: not correctly identified
in
Setup.
02D0
System cache error -
Cache
disabled
Contact Panasonic Technical Support.
02F0;
CPU
ID:
CPU
socket
number
for
Multi-Processor
error.
02F4:
EISA
CMOS
not writable
ServerB10S2
test error:
Cannot write to
EISA
CMOS.
19