Panasonic CF-R1 SERIES Operating Instructions Manual page 22

Dealing with
Problems
(Summary)
Display
No
display after
powering on
When
there
is
no
display
to
an external display,
•
Check your
cable connection
to
the external display.
•
Confirm your
display
is
powered
on.
•
Check
the settings for
your
external display.
•
Confirm
the following
setting
is
set
to
[ON].
tWinclowsT2000l
[Control Panel] - [Display]
-
[Settings] -
[Advanced]
-
[Lynx3DM+]
-
[CRT]
[Control Panel] -
[Appearance and
Themes]
-
[Display]
- [Settings] -
[Advanced]
-
[Lynx3DM+]
-
[CRT]
Try changing the display
by
pressing
(
Fn
)
+
(
F3
)
.
When
displaying only through an
external display,
if
the
computer
is
shut
down
by
using
the
standby or hibernation
function, there will
be no
display
on
the
LCD
unless the
exter-
nal
display
is
co nnecte
d
when
operations are
resumed.
In
this
case,
connect
the external
display or press
C
Fn
)
+
C
F3
)
.
The power
has not been
turned
off,
but after a cer-
tain
period of time, there
is
no
display
•
Has
the
computer been
set to
the
power-saving
mode?
To resume
operation
of your
computer from
the
condition
the
power
of
the display
is
off
(for
energy co
nservatio
n purposes), press
any key
unrelated
to
the direct triggering of a
selection, like (
^^ift
)
.
•
To save power, your
computer
may
have automatically entered
the
standby or hiberna-
tion
mode. (Q=
"Computing
On
the
Road")
Slide the
power
switch.
•
There
is
a possibility that
an external display
is
set as
the display destination.
Press C£n!)
+
CUD
to
switch the display
d
estina
tio
n.
•
Did you repeatedly an d cont
in
uously press
C
Fn
3
+
C
F3
)
?
Before holding
down
C
Fn
)
+
C
F3
J
,
make
sure the display destination has
been com-
pletely
switched.
The
cursor
cannot be
con-
trolled
Restart the
computer
by using
the
keyboard
(e.g.,
An
afterimage
appears
(e.g.,
green, red,
and blue dots
remain on
the display) or
there are dots not display-
ing the correct colors
If
an
image
is
displayed for
a
prolonged period of time, an afterimage
may
appear.
This
is
not a
malfunction.
The
afterimage will
disappear
when
a different screen
is
displayed.
High-precision
and advanced technologies are necessary
in
the
production of
color
liquid
crystal
displays (color
LCDs).
Therefore,
if
0.002%
or
less
of the picture elements
either
fail
to light
or
remain constantly
lit
(that
is,
more
than
99.998% of elements
are function-
ing properly),
no
defect
is
considered
to exist.
The
external display
no
longer displays properly
When
an
external display not
compatible with
the
power
saving
mode
is
used with
the
computer,
the external display
may
no longer display properly
when
the
computer
enters the
condition the
power
of the display
is
OFF
(for
energy conservation purposes). In such
cases, turn off the
power
to
the external display.
The
screen
becomes
disor-
dered
Changing
the
number
of
colors
of the display
may
affect
the screen. Restart the
computer.
During simultaneous
dis-
play,
the screen of the exter-
nal display
becomes
disor-
dered
Try changing the display
by
pressing
(
Fn
] -H
C
F3
j
.
When
setting the
Screensaver,
an
error
may
occur during a
resume
op-
eration
When
the
computer
enters the
standby or hibernation
mode
while the scree nsaver
is
run-
ning,
an error
may
occur during
a
resume
operation.
In
such cases, turn off the
Screensaver
or try
changing the pattern
of the screensaver.
When
an
MPEG
file is
be-
ing
played with
Media
Player, the display destina-
tion
cann
ot
be switched
us-
ing
[
Fn
)
+i
Set the following
setting to
[OFF],
|Winci^200^
[Start]
- [Settings]
- [Control Panel] -
[Display]
-
[Settings]
-
[Advanced]
-
[Lynx3DM+]
[Stretch]
[start]
-
[Control Panel]
-
[Appearance and
Themes]
-
[Display]
-
[Settings]
-
[Advanced]
[Lynx3DM+l
- [Stretch]