Dvd audio-video / super audio cd player (147 pages)
Summary of Contents for Denon DVD-3930
Page 1
修理の際は、必ず取扱説明書を参照の上、作業を行っ ● ● operating instructions without fail. てください。 Some illustrations using in this service manual are 本文中に使用しているイラストは、説明の都合上現物 ● ● slightly different from the actual set. と多少異なる場合があります。 TOKYO, JAPAN Denon Brand Company, D&M Holdings Inc. X0274 V.01 DE/CDM 0607...
DVD-3930/3930CI SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check.
DVD-3930/3930CI WIRE ARRANGEMENT ワイヤー整形図 If wire bundles are untied or moved to perform adjustment or 調整や部品の交換等により、ワイヤー類の結束をはずしたり移 parts replacement etc., be sure to rearrange them neatly as 動させた場合には、それらの作業が完了した時点でワイヤーの they were originally bundled or placed afterward. 整形をおこなってください。正しく整形されてないとノイズ発 Otherwise, incorrect arrangement can be a cause of noise 生の原因となることがあります。...
Page 4
DVD-3930/3930CI DISASSEMBLY 各部のはずしかた (Follow the procedure bellow in reverse order when (組み立てるときは、逆の順序でおこなってください。 ) reassembling.) Disassembly and abandonment 分解と廃棄 (1) Disassembly of a set (1) セットの分解 It decomposes according to a work procedure 1.~11. 作業手順 1. ∼ 11. 項に従い分解を実施します。 clause. (2) 使用部品の分別...
Page 5
DVD-3930/3930CI 1. Top cover & Inner cover 1. Top cover & Inner cover 1.1. Top cover 1.1. トップカバー (1) Remove 2 screws (s • 1) on the rear side and (1) 背面側から s ・ 1 のねじ 2 本と天・側面から s ・ 2 の...
Page 6
DVD-3930/3930CI 2. DVD mechanism ass'y 2. DVD mechanism ass'y 2.1. When the Disc tray can be ejected electrically. 2.1. ディスクトレイが電動でオープン出来る場合 (1) Switch on, and press [OPEN/CLOSE] button to open the (1) 電源を入れ「 OPEN/CLOSE 」ボタンを押して、 ディスクト Disc tray. レイを開きます。 (2) Detach the Loader panel ass'y (c • 1) by lifting.
Page 7
DVD-3930/3930CI 3. Front panel sub ass'y 3. Front panel sub ass'y (1) Disconnect the wire [CX031] [CX025] connecting From (1) a ・ 1:Front panel sub ass'y からのワイヤー [CX031] the Front panel sub ass'y (a • 1). [CX025] をはずします。 (2) Remove 2 top screws (s • 3) and 4 bottom screws (s • 1), (2) 天面から...
Page 8
DVD-3930/3930CI 4. Power P.W.B. ass'y etc. 4. Power P.W.B. ass'y etc. 4.1. Power P.W.B. ass'y 4.1. 電源基板 ass'y (1) Remove 1 screw (s • 6) and 2 nut (s • 7) on the rear side. (1) 背面から s ・ 6 のねじ 1 本と s ・ 7 のナット 2 本をはずし...
Page 9
DVD-3930/3930CI 5. Block of Video P.W.B. 5. Block of Video P.W.B. 5.1. Support bracket ass'y 5.1. サポート板金 ass'y (1) Remove 2 rear screws (s • 1) and a side screw (s • 1) and (1) 背面の s ・ 1 のねじ 2 本、側面の s ・ 1 のねじ 1 本、天面...
Page 10
DVD-3930/3930CI 6. Block of Audio P.W.B. 6. Bloack of Audio P.W.B. 6.1. Block of AUDIO P.W.B. 6.1. オーディオ基板ブロック (1) Remove 4 screws (s • 1) and 10 screws (s • 12) on the (1) 背面から s ・ 1 のねじ 4 本と s ・ 12 のねじ 10 本と天面か...
Page 11
DVD-3930/3930CI 8. Parts on Front panel sub ass'y (a • 1) 8. Parts on Front panel sub ass'y(a ・ 1) 8.1. Display P.W.B. ass'y 8.1. ディスプレイ基板 (1) Remove 10 screws (s • 6). (1) s ・ 6 のねじ 10 本をはずします。...
Page 12
DVD-3930/3930CI DIAGNOSTICS OF OPTICAL PICKUP 光ピックアップの故障診断とトラバース AND REPLACING TRAVERSE UNIT ユニットの交換 Make failure diagnostics of the Optical Pickup as follows. 次の順序で故障診断を行ってください。 If the laser drive current (Iop) becomes more than 1.5 times of レーザー駆動電流 Iop 値が初期値の 1.5 倍以上になっている the initial value, the Optical Pickup should be replaced.
Page 13
DVD-3930/3930CI 1. Iop checked Method 1. Iop 値の確認方法 Select the laser ON/OFF (CD/DVD) mode of the test mode, レーザー駆動電流を確認する場合は、テストモードのレー and check the lop value of DVD laser or CD laser. ザー ON/OFF (CD/DVD) モードを選択して、DVD レーザー (See page 19 for test mode.) または...
Page 14
DVD-3930/3930CI 4. Rewriting the default value of the laser 4. レーザー電流初期値の書き換え方法 current レーザー電流の初期値を書き換えるには、CD または DVD レーザー電流が表示されている時に PLAY ボタンを 5 秒以 To rewrite the default value of the laser current, press the PLAY button for at least 5 seconds while the CD or DVD la- 上押し、次に...
Page 15
DVD-3930/3930CI How to Replace Traverse Unit トラバースユニットの交換方法 1. Preparing for Replacement 1. トラバースユニット交換準備 (1) Removing Clamp Base Damper (1) クランプベースダンパーのはずしかた Remove 4 pcs of 2.6mm machine screw (a), and detach the Clamp Base Damper 2.6mm マシンネジ (a) 4 本をずして、クランプベースダンパー クランプベースダンパー...
Page 16
DVD-3930/3930CI 3. Installing Loader 3. ローダーの組み立て (1) Inserting Loader (1) ローダーの挿入 Set and push the Loader to the arrow direction until it stops. Plate Gear ローダーを矢印の方向へ止まるまで押しこみます。 プレートギア When installing the Loader, move Plate Gear to right before- ローダーを組み込み時、プレートギアのボスがトレイ裏面の hand so as that the boss of the Plate Gear fits in the backside 溝に合うようにプレートギアを右側へ寄せておきます。...
Page 17
DVD-3930/3930CI 5. Assembly (2) 5. 組み立て(2) (1) Attaching Tape to Clamp Base Damper (1) クランプベースダンパーへのアセクロ貼り付け Attach acetate cloth tape to 3 projections of the Clamp Base クランプベースダンパー裏面の突起 3 箇所へアセテートクロ Damper backside. Acetate Cloth Tape アセテートクロステープ ステープを貼り付けます。 (2) Assembling Clamp Base (2) クランプベースの取り付け...
DVD-3930/3930CI SERVICE MODE サービスモードについて 1. Aging Mode 1. エージングモード (1) preparation (1) 準備 (a) Equipment used: Any one of DVD Karaoke Disc (containing more than 10 titles). (a) 使用機器:DVD カラオケディスク(10 タイトル以上の物) 。 (b) Unit setting : No spec other than the following procedure (Aging mode).
Page 19
DVD-3930/3930CI 4. Test mode 4. テストモード (1) Entering the test mode (1) テストモードの設定 To enter the test mode, press the STOP and SKIP FWD buttons simultaneously while in the heat run mode. テストモードの設定はヒートランモード時に STOP ボタンと SKIP FWD ボタンを同時押しで行う。 Basically, enter the test mode while in the stop mode after the disc is loaded.
Page 20
DVD-3930/3930CI FL Display (The display part of 13 digits) FL 管の表示 (13 桁の表示部 ) T B T B FL Display (The display part of 13 digits) FL 管の表示 (13 桁の表示部 ) T C T C FL Display (The display part of 13 digits) FL 管の表示...
Page 21
DVD-3930/3930CI (3) Setting the mode (3) モードの確定 With the mode selected, press the PLAY button to set that mode. モードを選択してある状態で PLAY ボタンを押すとモードを確定する。 ① In the FL tube lighting mode, the FL tube display turns all on and all off. (When "T0" is displayed, the display switches between ①...
Page 22
DVD-3930/3930CI ⑦ Displaying the accumulated laser on time (stored in the EEPROM) ⑦レーザー ON 累積時間 (EEPROM に記憶 ) を表示する。 FL 管の表示 (13 桁の表示部 ) FL Display (The display part of 13 digits) T Y ― ― ― n n n...
Page 23
DVD-3930/3930CI (4) Change within the mode (4) モード内での変更 Changes within modes are made by pressing the SKIP REV and SKIP FWD buttons while the mode is set. モードを確定してある状態で SKIP REV ボタン又は SKIP FWD ボタンを押すとモード内での変更を行う。 ① In the laser on/off mode ①レーザー...
Page 24
DVD-3930/3930CI ⑥ In the accumulated laser on time display ⑥レーザー ON 累積時間を表示場合 FL 管の表示 (13 桁の表示部 ) FL Display (The display part of 13 digits) T Y ― ― ― n n n n n 。 n T Y ―...
Page 25
DVD-3930/3930CI (5) Execution of trace mode (error rate display) (See "Table 3 - Trace mode details") (5) トレースモード ( エラーレート表示 ) の実行 ( 表 3 トレースモード詳細 参照) Trace will be performed if the PLAY button is pushed after choosing operation.
Page 26
DVD-3930/3930CI (7) Test mode detailed table (7) テストモード詳細一覧表 Table 1: Servo adjustment value display mode details 表 1 サーボ調整値表示モード詳細 Name Meaning Remarks TXX 名称 意 味 備 考 gavine0 L0 layer VIN5VIN6VIN7VIN8 Fep section VIN5 = "C" signal Fep section middle stage and latter stage amplifier set- gavine0 L0 層...
Page 27
DVD-3930/3930CI Name Meaning Remarks TXX 名称 意 味 備 考 tkga0 L0 layer tracking Loop Gain adjustment 1x for 0x100 [0x200 (2x) set to Typ. tkga0 L0 層トラッキング Loop Gain 調整値 0x100 で 1 倍 [0x200(2 倍 ) を Typ に設定する。] value (1x for 0x100, 2x for 0x200.
Page 28
DVD-3930/3930CI Name Meaning Remarks TXX 名称 意 味 備 考 oftpd1 L1 layer DVD tracking balance adjust- "A" and "C" signals: same phase oftpd1 L1 層 DVD トラッキングバランス調整値 "A" と "C" 信号が同位相 ment value "B" and "D" signals: same phase "B"...
Page 29
DVD-3930/3930CI Table 3: Trace mode details 表 3 トレースモード詳細 Contents Contents supplement YY 内容 補足説明 A display of PO error detection number of the inner circumference It is invalid at the time of CD operation. 1 層内周の PO 誤り検出数とアドレスの表示 CD 時は無効。...
Page 31
DVD-3930/3930CI 2. GU-3749-1 (MAIN UNIT) 2. GU-3749-1 (MAIN UNIT) 2.1. FL TUBE dosen't light 2.1. FL 管点灯せず (1) Check the Set-up process of System (1) システム立ち上がりチェック工程 Check Power Supply Voltages. 電源電圧確認 Check Soldering. 半田付けを確認 GU-3749-1(MAIN UNIT) N.G. GU-3749-1(MAIN UNIT) N.G.
Page 32
(2) GU-3750-1 is N.G. ・ テストモード T0 実行 全点灯 OK? The FL tube display turns all on? O.K. O.K. 終了 2.2. Image is not displayed. (Blue-back, DENON wallpaper) 2.2. 映像出力せず。 (ブルーバック、DENON 壁紙) Check Digital output signal for Video. [1] Check Soldering. 映像用デジタル信号出力確認 [1] 半田付けを確認...
Page 33
DVD-3930/3930CI (2) CD or DVD チェック工程 (2) CD or DVD check process Check the RF signal. RF 信号の確認 半田付けを確認 GU-3749-1(MAIN UNIT) GU-3749-1(MAIN UNIT) Check Soldering. N.G. GU-3749-1(MAIN UNIT) N.G. ・ テストポイント (TP) の電圧確認 • Check the voltage of Test-Point (TP)) GU-3749-1(MAIN UNIT) ・...
DVD-3930/3930CI ELECTRICAL ADJUSTMENT FOR VIDEO ビデオ回路の調整 1. SETTING 1. セッティング手順 (1) Connect the monitor TV to the video output terminal. (1) セットの VIDEO OUT 端子にテレビモニターを接続する。 (2) Connect the oscilloscope to the Y-signal and C-signal of (2) セットの S2 VIDEO OUT 端子から Y 信号と C 信号をそ...
Page 41
DVD-3930/3930CI 3. PROCEDURE 3. 手順 (1) Adjust the signal of S-VIDEO out by the wave of oscillo- (1) セットの S2 VIDEO OUT の信号レベルをオシロスコープ scope. 上の波高値で調整する。 (a) Target, Y-signal (a) Y 信号レベル Point VR551 調整個所 :VR551 Adjustment Value 1000 ± 20mV 調整値...
Page 42
DVD-3930/3930CI (c) Target, P -signal (c) P 信号レベル Check Value *525 ± 10mV 調整値 : 525 ± 10mV Waveform 波形 -signal 信号レベル * : 486 ± 10mV for U.S.A. & Canada model...
Page 44
DVD-3930/3930CI SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. 主な半導体を記載しています。汎用の半導体は記載を省略しています。 1. IC’s Note : Abbreviation ahead of IC No. indicates the name of P.W.B., etc. 注 ) : IC No. の前の記号は、基板の名称を表します。 MA : MAIN/A. VIDEO P.W.B.
Page 45
DVD-3930/3930CI Pin No. Signal Name Type Description Ground RESET Device reset pin Ground Core Supply CLKIN Alternate clock input (3.3-V LVCMOS Input) Ground Test Mode Select Core Supply TRST Test Reset OSCV Oscillator VSS tap point (for filter only) OSCIN 1.2-V Oscillator Input...
Page 46
DVD-3930/3930CI Pin No. Signal Name Type Description EM_A[6] EMIF Address Bus I/O Supply Ground EM_A[5] EMIF Address Bus EM_A[4] EMIF Address Bus Core Supply EM_A[3] EMIF Address Bus Ground EM_A[2] EMIF Address Bus EM_A[1] EMIF Address Bus Core Supply EM_A[0]...
Page 47
DVD-3930/3930CI MN2DS0009AA (MA: IC157) MN2DS0009AA Terminal Function Pin No. Pin Name Type Symbol Function MDQ18 SDRAM DATA18 SDRAM data 18 VDD33 3.3V I/O supply MDQ28 SDRAM DATA28 SDRAM data 28 MDQ19 SDRAM DATA19 SDRAM data 19 MDQ27 SDRAM DATA27 SDRAM data 27...
Page 48
DVD-3930/3930CI Pin No. Pin Name Type Symbol Function EXADT1 EXT ADR1 External memory address 1 / data 15 EXT ADR20 External memory address 20 Serial 0 output data Serial 0 clock VDD33 3.3V I/O supply SYSRXD Serial 1 input data...
Page 49
DVD-3930/3930CI Pin No. Pin Name Type Symbol Function VIN9 VIN9 CD head input VIN5 VIN5 CD head input VIN6 VIN6 CD head input VIN7 VIN7 DVD head input VIN8 VIN8 DVD head input VIN3 VIN3 DVD head input VIN4 VIN4...
Page 50
DVD-3930/3930CI Pin No. Pin Name Type Symbol Function VDD33 3.3V I/O supply MDQ15 SDRAM DATA15 SDRAM data 15 MDQO SDRAM DATA0 SDRAM data 0 MDQ14 SDRAM DATA14 SDRAM data 14 MDQ1 SDRAM DATA1 SDRAM data 1 MDQ13 SDRAM DATA13 SDRAM data 13...
Page 58
DVD-3930/3930CI Terminal Functions Pin Name Functions 1 VSC It fixed to ground.( for Core) Latch input for µCOM serial communication. 2 XMSLAT Shift clock input for µCOM serial communication. 3 MSCK Data input for µCOM serial communication. 4 MSDATI 5 VDC +2.5V Power for Core.
Page 59
DVD-3930/3930CI Pin Name Functions 50 TESTO Output for TEST. (open) 51 TESTI Input for TEST. It fixed to “L” potential. 52 TESTI Input for TEST. It fixed to “L” potential. 53 TESTO Output for TEST. (open) 54 VDC +2.5V Power for CORE.
Page 60
DVD-3930/3930CI Pin Name Functions 96 TESTI TEST input terminal. It fixed to “L” potential. 97 TESTI TEST input terminal. It fixed to “H” potential. 98 TESTO TEST output terminal. (open) 99 VDC +2.5V Power for CORE. 100 TESTI TEST input terminal. It fixed to “L” potential.
Page 61
DVD-3930/3930CI Pin Name Functions 148 A11 Address output terminal for SDRAM. (MSB) 149 A10 Address output terminal for SDRAM. 150 VSC Ground for CORE. 151 A9 Address output terminal for SDRAM. 152 A8 Address output terminal for SDRAM. 153 VDC +2.5V Power for CORE.
Page 62
DVD-3930/3930CI PCM1796DBR (AU: IC401, 406, 411, 702, 707) (TOP VIEW) ZEROL ZEROR AGND3L MSEL L− LRCK DATA AGND2 DGND AGND1 R− AGND3R PCM1796DBR Block Diagram I OUT L− LRCK Current V OUT L Segment DATA Audio I OUT L+ Data Input...
DVD-3930/3930CI PCM1796DBR Terminal Function TERMINAL DESCRIPTIONS DESCRIPTIONS NAME AGND1 − Analog ground (internal bias) AGND2 − Analog ground (internal bias) AGND3L − Analog ground (L-channel DACFF) AGND3R − Analog ground (R-channel DACFF) Bit clock input (1) Serial audio data input (1)
Page 68
DVD-3930/3930CI TOP247Y (PD: IC901) Tab Internally Connected to SOURCE Pin DRAIN (D) CONTROL (C) INTERNAL SUPPLY SHUNT REGULATOR/ ERROR AMPLIFIER SOFT START 5.8 V 4.8 V 5.8 V INTERNAL UV I FB COMPARATOR V I (LIMIT) CURRENT LIMIT SOFT START ADJUST ÷...
Page 69
DVD-3930/3930CI AK4101AVQ (AU: IC106) AK4101VQ Terminal Function Pin No. Pin Name Function Power down and reset pin MCLK Master clock input pin SDTI1 Audio serial data input 1 pin SDTI2 Audio serial data input 2 pin SDTI3 Audio serial data input 3 pin...
Page 71
DVD-3930/3930CI 6. FL DISPLAY FL TUBE (15-BT-97GNK) (PD: FL101) SUPER DVD GROUP TITLE TRACK CHAP ANGLE D.MIX PROG RAND TOTAL SING REM HDCD DIGITAL AUDIO VCD L.PCMP.PCM 1 A-B MPEG JPEG PROGRESSIVE WMA MP3 HDMI 480P 576P F V G...
DVD-3930/3930CI NOTE FOR PARTS LIST 部品表について • Part indicated with the mark "nsp" are not always in stock and possibly to 1.nsp 印の部品は常時在庫していませんので供給に長時間を要すること take a long period of time for supplying, or in some case supplying of part があります。 may be refused.
Page 81
DVD-3930/3930CI PARTS LIST OF P.W.B. UNIT (for E3 model) *本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. * "nsp" 印の部品は常時在庫していませんので供給に長時間を要することがあります。場合によっては、供給をお断りする場合があります。 * Part indicated with the mark “nsp” are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused.
Page 82
DVD-3930/3930CI Ref. No. Part No. Part Name Remarks Q'ty New RESISTORS GROUP R151 00D 244 2051 945 RS14B3A010JNBST(S) RR301 00D 247 2020 933 RM73B--103FT +1608 RR303 00D 247 2020 933 RM73B--103FT +1608 RR304 00D 247 2028 906 RM73B--302FT +1608 RR316...
Page 100
DVD-3930/3930CI Ref. No. Part No. Part Name Remarks Q'ty New CY064 00D 205 0449 062 6P VH CONNECTOR BASE CY122 00D 205 1386 085 12P BASE(9115B-PT1) CY125 00D 205 1386 085 12P BASE(9115B-PT1) CY131 00D 205 0892 088 13P FFC CON. BASE...
Page 101
DVD-3930/3930CI PARTS LIST OF P.W.B. UNIT (for E2, model) *本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. * "nsp" 印の部品は常時在庫していませんので供給に長時間を要することがあります。場合によっては、供給をお断りする場合があります。 * Part indicated with the mark “nsp” are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused.
Page 120
DVD-3930/3930CI Ref. No. Part No. Part Name Remarks Q'ty New OTHERS PARTS GROUP CX123 00D 205 1324 021 12P PIN HEADER(9120) CX162 00D 205 1324 063 16P PIN HEADER(9120) CX811 00D 205 1394 006 19P HDMI CONNECTOR CY041 00D 205 0343 045 4P CONN.BASE(KR-PH)
Page 121
DVD-3930/3930CI PARTS LIST OF P.W.B. UNIT (for JP model) *本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. * "nsp" 印の部品は常時在庫していませんので供給に長時間を要することがあります。場合によっては、供給をお断りする場合があります。 * Part indicated with the mark “nsp” are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused.
Page 122
DVD-3930/3930CI Ref. No. Part No. Part Name Remarks Q'ty New D101,102 00D 276 0401 905 1SS133T77 (TAPE) D152 00D 276 0401 905 1SS133T77 (TAPE) D500 00D 276 0717 903 1SS355 TE-17 RESISTORS GROUP R151 00D 244 2051 945 RS14B3A010JNBST(S) RR301...
DVD-3930/3930CI EXPLODED VIEW WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. 印の部分は安全を維持するために重要 な部品です。従って交換時は必ず指定の 部品を使用してください。...
DVD-3930/3930CI PARTS LIST OF EXPLODED VIEW *本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. * "nsp" 印の部品は常時在庫していませんので供給に長時間を要することがあります。場合によっては、供給をお断りする場合があります。 * Part indicated with the mark “nsp” are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused.
Page 143
DVD-3930/3930CI Ref. No. Part No. Part Name Remarks Q'ty New 00D 412 5304 001 MAIN PWB BRACKET(3930) 00D 461 1248 024 RUBBER SHEET 00D 412 5342 005 MECHA SIDE COVER 00D 513 3406 107 LABEL(A) E3 Model 00D 513 3463 001...
Page 144
DVD-3930/3930CI Ref. No. Part No. Part Name Remarks Q'ty New 00D GEN 8143 -2 L/P SUB ASSY(3930SP) P.Silver Model EMIGASKET RFSG100100 30mmx4 EMIGASKET RFSG100100 20mmx2 EMIGASKET RFSG020070 20mmx4 EMIGASKET RFSG003050 10mmx1 EMIGASKET RFSG030100 40mmx1 00D 342 0032 008 FERRITE CLAMP(RFC-6)
Page 145
DVD-3930/3930CI Ref. No. Part No. Part Name Remarks Q'ty New Screws 00D 473 7034 002 3X6 CPTS(S)-NI 0RD 471 2303 020 3X6 CFS-B 0RD 471 2305 015 3X10 CFS 0RD 471 3304 015 3X8 CBS-Z 0RD 471 8010 100 SPECIAL SCREW...
Page 146
DVD-3930/3930CI EXPLODED VIEW OF DVD MECHANISM UNIT WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. 印の部分は安全を維持するために重要 な部品です。従って交換時は必ず指定の 部品を使用してください。...
Page 147
DVD-3930/3930CI PARTS LIST OF DVD MECHANISM UNIT (FG180-3) *本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. * "nsp" 印の部品は常時在庫していませんので供給に長時間を要することがあります。場合によっては、供給をお断りする場合があります。 * Part indicated with the mark “nsp” are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused.
DVD-3930/3930CI PACKING VIEW PARTS LIST OF PACKING & ACCESSORIES *本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. * "nsp" 印の部品は常時在庫していませんので供給に長時間を要することがあります。場合によっては、供給をお断りする場合があります。 * Part indicated with the mark “nsp” are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused.
DVD-3930/3930CI MEASURING METHOD AND WAVEFORMS 各部の波形と測定方法 To check the waveforms on the Main P.W.B., the GND (-) メイン基板の波形チェックを行うためにはオシロスコープ probe of the oscilloscope to “Vref” point. の GND(-) プローブを "Vref" ポイントに接続します。 (Except for lnner SW, TRVSW) 注 意 NOTES 測定ディスク: DVD/DVDT-S01 or TDV-520A...
Page 153
DVD-3930/3930CI WAVEFORMS GU-3749-1 MAIN P.W.B. DVD PLAY Disc: TDV-520A CD PLAY Disc: TCD-784 DVRF waveform DVRF waveform ⑮AMON1 ⑮AMON1 DVD LOADING PLAY CD LOADING PLAY ①FOO ①FOO ②F+ ②F+ ③F- ③F- DVD PLAY CD PLAY ④TRO ④TRO ⑤T+ ⑤T+ ⑥T- ⑥T-...
DVD-3930/3930CI NOTE FOR SCHEMATIC DIAGRAM 配線図について WARNING: ! 印の部品は安全を維持するために重要な部品です。 Parts marked with this symbol ! have critical characteristics. 従って交換時は必ず指定の部品を使用してください。 Use ONLY replacement parts recommended by the manufactur- 注) CAUTION: (1) 指定なき抵抗値は Ω、k は kΩ、M は MΩ を示す。 Before returning the unit to the customer, make sure you make (2) 指定なきコンデンサーの値は...
Page 156
DVD-3930/3930CI SCHEMATIC DIAGRAMS (1/20) SIGNAL LINE SCHEMATIC DIAGRAMS (1/20) GU-3749-1 MAIN UNIT (1/2)
Page 157
DVD-3930/3930CI SCHEMATIC DIAGRAMS (2/20) SIGNAL LINE SCHEMATIC DIAGRAMS (2/20) GU-3749-1 MAIN UNIT (2/2)
Page 158
DVD-3930/3930CI SCHEMATIC DIAGRAMS (3/20) PROGRESSIVE VIDEO SIGNAL LINE INTERLACE VIDEO SIGNAL LINE SCHEMATIC DIAGRAMS (3/20) GU-3749-2 VIDEO UNIT (1/2) GU-3749-3 BNC UNIT (for E3 model)
Page 159
DVD-3930/3930CI SCHEMATIC DIAGRAMS (4/20) PROGRESSIVE VIDEO SIGNAL LINE INTERLACE VIDEO SIGNAL LINE SCHEMATIC DIAGRAMS (4/20) GU-3749-2 VIDEO UNIT (1/2) GU-3749-3 BNC UNIT (for E2 model)
Page 160
DVD-3930/3930CI SCHEMATIC DIAGRAMS (5/20) PROGRESSIVE VIDEO SIGNAL LINE INTERLACE VIDEO SIGNAL LINE SCHEMATIC DIAGRAMS (5/20) GU-3749-2 VIDEO UNIT (1/2) GU-3749-3 BNC UNIT (for JP model)
Page 161
DVD-3930/3930CI SCHEMATIC DIAGRAMS (6/20) INTERLACE VIDEO SIGNAL LINE SCHEMATIC DIAGRAMS (6/20) GU-3749-2 VIDEO UNIT (2/2) (for E3 model)
Page 162
DVD-3930/3930CI SCHEMATIC DIAGRAMS (7/20) INTERLACE VIDEO SIGNAL LINE SCHEMATIC DIAGRAMS (7/20) GU-3749-2 VIDEO UNIT (2/2) (for E2 model)
Page 163
DVD-3930/3930CI SCHEMATIC DIAGRAMS (8/20) INTERLACE VIDEO SIGNAL LINE SCHEMATIC DIAGRAMS (8/20) GU-3749-2 VIDEO UNIT (2/2) (for JP model)
Page 164
DVD-3930/3930CI SCHEMATIC DIAGRAMS (9/20) SCHEMATIC DIAGRAMS (9/20) GU-3750-1 DISPLAY UNIT GU-3750-4 A.CONNECT UNIT GU-3750-5 2nd SW UNIT GU-3750-9 DIGITAL OUT UNIT...
Page 165
DVD-3930/3930CI SCHEMATIC DIAGRAMS (10/20) SCHEMATIC DIAGRAMS (10/20) GU-3750-2 DIGTAL POWER UNIT GU-3750-3 P.SW UNIT GU-3750-6 V.CONNECT UNIT-1 GU-3750-7 V.CONNECT UNIT-2 GU-3750-8 V.CONNECT UNIT-3 GU-3793 FAN POWER UNIT...
Page 166
DVD-3930/3930CI SCHEMATIC DIAGRAMS (11/20) SIGNAL LINE SCHEMATIC DIAGRAMS (11/20) GU-3751-1 AUDIO (DIGITAL) UNIT (1/2)
Page 167
DVD-3930/3930CI SCHEMATIC DIAGRAMS (12/20) SIGNAL LINE SCHEMATIC DIAGRAMS (12/20) GU-3751-1 AUDIO (DIGITAL) UNIT (2/2)
PRINTING THE SERVICE MANUAL The PDF of this service manual is not designed to be printed from cover to cover. The pages vary in size, and must therefore be printed in sections based on page dimensions. NON-SCHEMATIC PAGES Data that does NOT INCLUDE schematic diagrams are formatted to 8.5 x 11 inches and can be printed on standard letter-size and/or A4-sized paper. SCHEMATIC DIAGRAMS The schematic diagram pages are provided in two ways, full size and tiled.
Need help?
Do you have a question about the DVD-3930 and is the answer not in the manual?
Questions and answers