Initial Installation Wizard - Sharp LC-46HD1E Operation Manual

Initial installation

Initial installation wizard

When the TV powers on for the first time after
purchase, the initial auto installation wizard appears.
Follow the menus and make the necessary settings
one after another.
Initial installation -> Language
Proceed
NOTE
• You can repeat this installation process by conducting the
"Repeat initial installation" command. Press INFO, the
option is located in the third line from the top.
Buttons to be used:
a/b/c/d:
Move the cursor and select the settings.
OK:
Press to confirm and proceed to the next step.
YELLOW:
In some screens you can select or deselect
items with YELLOW. When an item is selected,
it is marked with ✔.
Initial installation -> Connect antenna cable(s)
Antenna cable(s) for:
Antenna/cable (analogue)
DVB-T
DVB-C
DVB-S (cable 1)
DVB-S (cable 2)
BACK:
Press to go back one step.
END:
If this icon is visible, you can exit the wizard.
Table of setting options in initial installation
wizard
There are numerous settings in the initial installation
wizard. When in doubt, refer to the table below so you
don't get overwhelmed.
Items
Language Select the language.
Antenna/cable (analogue): analogue stations
via cable/antenna
Connect
DVB-T: digital, terrestrial stations
antenna
DVB-C: digital stations via cable
cable(s)
DVB-S (cable 1): digital stations via satellite
DVB-S (cable 2): digital stations via satellite
If you are using an active antenna, then select
Antenna DVB-T
yes (5V) for the antenna power supply.
10
Downloaded From TV-Manual.com Manuals
to antenna socket(s):
Explanation
Items
The conventional settings will be derived from
the selection of set location. Only change this
if you know other symbol rates and modulation
types or if you have to specify the network ID for
Antenna
your cable network (information available from
DVB-C
your cable network provider). If you want to run
the station search independently of the channel
grid, select frequency search for the search
method.
Select which satellite(s) you receive from a list.
For more than one satellite, select the type of
Antenna
your changeover switch or communal satellite
DVB-S
system additionally. Ask your dealer in this
regard.
Specify here whether the high band of the
High band selected satellite is to be searched in addition to
the low band.
Normally, you do not need to change the values
for high and low band, unless the LNC (LNB) of
LNB
your satellite system uses a different oscillator
frequencies
frequency (important for the frequency display).
Low Band/High
After you have made these settings, you should
Band
receive the picture and sound of the selected
satellites (only with Astra1 and HOTBIRD).
The symbol rates are specified by the satellite
Symbol rates provider and do not normally need to be
changed.
Select the signal source from a list, the station
of which is to be at the top of your station list
(starting with station slot 1).
Favoured signal
• If you want to use the AV Link function with an
source
externally connected recorder, the analogue
stations have to be between station slot 1 and
99.
Start the automatic station search with OK. First
TV stations, then radio stations are searched
for. The stations found in the automatic search
are divided into the appropriate station blocks
depending on the previously selected antenna
cables (signal sources). Subsequently the
Start search stations can only be re-sorted within these
blocks. At the beginning of the station list
you will find the block with the stations of the
preferred signal source.
Any mixed sorting of stations from different
signal sources is only possible with the
favourites list.
In conclusion the connection wizard will start;
with their help you can register and set your
video devices or decoders, and connect them to
Connecting the TV set. DVD players and DVD recorders are
additional already registered at the factory.
devices You can start the connection wizard manually
later and add new devices. Further information
is available on page 15 (Connection wizard) and
page 22 (Speaker/amplifier connection).
With good reception conditions a room antenna
Room antenna
can be used for DVB-T (socket ANT2).
Under less favorable reception conditions, it is
advisable to use an active antenna which has to
be set accordingly in the initial installation or in
Active antenna
the "TV Menu > Connections > Antenna DVB >
Antenna DVB-T". (See "Antenna DVB-T" on this
page).
If the location is outside of the normal
Unidirectional
transmission range then a directional antenna
antenna
can be used to improve reception quality.
Explanation