Table of Contents
Advertisement
Submenu "HEATING"
In this sub-menu „HEATING" you can choose a control program for battery
warmer pockets or alternatively a program for the control of tire warmers, by
tapping the appropriate icon, in both parts of the program the charger handles
both power consumption as well as the control of the connected heater.
Connect the battery or tire warmer connectors directly to the charge outputs
CH1 or CH2 and the temperature sensor to the associated sensor connector.
If necessary, both outputs are completely independent and they can be used
at the same time.
Display "Battery warmer"
# Parameter
Short description
1
Temperature Adjustable in the range of 10 ... 45 ° C (default 25 ° C)
2
Alarm
Adjustable in the range 1 ... 300 minutes (default 55 m)
3
Voltage
Adjustable in the range of 5 ... 15 volts in 0.1 V incre-
ments (default 12.00 V)
4
0m
Display of period since the program has started, time in
minutes
5
0s
Display of period from the program has started, time in
seconds
6
00.0°C
Display of the actually temperature measured by the
connected sensor
Pressing the ENTER buttons at the bottom right of the display starts the control program of the
battery warmer.
Pressing the STOP button at the bottom of the display stops the operation.
• The heater will continue heating even after the alarm!
• If you use a battery pack heat bag without temperature sensor, nor the tempera-
ture can be regulated neither the temperature can be displayed.
Set, for security reasons, the output voltage so that the battery does not overheat or even
ignite! Check the temperature reached on a regular basis or alternatively use one of the
temperature sensors supplied with the charger!
40
Display "tire warmer"
# Parameter
Short description
1
Temperature Adjustable in the range of 10 ... 99 ° C (default 55 ° C)
2
Alarm
Adjustable in the range 1 ... 300 minutes (default 55 m)
3
Voltage
Adjustable in the range of 5 ... 15 volts in 0.1 V increments
(default 12.00 V)
4
0m
Display of period since the program has started, time in
minutes
5
0s
Display of period from the program has started, time in
seconds
6
00.0°C
Display of the actually temperature measured by the
connected sensor
Pressing the ENTER buttons at the bottom right of the display starts the control program of the tire
warmer.
Pressing the STOP button at the bottom of the display stops the operation.
• The heater will continue heating even after the alarm!
• If you use a tire warmer without temperature sensor, nor the temperature can be
regulated neither the temperature can be displayed.
Set, for security reasons, the output voltage so that the tires do not overheat or even ignite!
Check the temperature reached on a regular basis or alternatively use one of the tempera-
ture sensors supplied with the charger!
Submenu "E.S.C"
In this submenu "ESC" (Electronic Speed Controller) can be programmed electronic motor control-
lers with three poles telemetry connector, analogue to the Graupner HoTT telemetry items.
NOTE:
• Once it is recalled the submenu "ESC" in a charge channel, the current on the other
charge channel process is interrupted.
• When connecting a controller with single-pole telemetry cable to the polaron EX-1400,
the data field of the display remains blank due to incorrect data connection.
Bring the operating element of your motor controller in the OFF position BEFORE turning
your receiver system on or alternatively disconnect the motor from the speed controller!
Only in this way it is ensured that the motor cannot start in any way. Connect afterwards
- as exemplified in the figure below - your car controller three-pin cable telemetry to the 'EXT.
MODULE " side port. Alternatively you can use a servo tester with an external power supply to
control the motor controller in OFF position.
Once you have turned on the power to your controller and connected the controller input, the page
INNOVATION & TECHNOLOGIE
41
Advertisement
Table of Contents
