Reinforcing The Bass; Muting The Sound; Changing The Display Brightness; Using The Sleep Timer - JVC RX-8030VBK Instructions For Use Manual

The following basic operations are possible only using the
remote control.
BASS
BOOST
Reinforcing the
Bass
7/P
SOUND
10/0
SLEEP
Using the Sleep
Timer

Reinforcing the Bass

You can boost the bass level.
• Once you have made adjustment, it is memorized for each source.
1. Press SOUND.
The 10 keys are activated for sound adjustments.
2. Press BASS BOOST to turn on Bass Boost.
The BASS BOOST indicator lights up.
• Each time you press the button, Bass Boost turns on ("BOOST
ON") and off ("BOOST OFF") alternately.
For RX-7030VBK:
You can use the BASS BOOST button on the front panel.
When the Bass Boost is activated, the lamp on the button lights up.
• Each time you press the button, Bass Boost turns on and off.
Notes:
• This function affects only the sounds from the front speakers,
center speaker, and subwoofer.
• When Analog Direct is in use (see page 21), the Bass Boost is
canceled temporarily.

Muting the Sound

Press MUTING to mute the sound through all speakers and
headphones connected.
"MUTING" appears on the display and the volume turns off (the
VOLUME level indicator goes off).
To restore the sound, press MUTING again.
• Turning MASTER VOLUME on the front panel or pressing
VOLUME +/– on the remote control also restores the sound.

Changing the Display Brightness

You can dim the display.
Press DIMMER.
• Each time you press the button, the brightness
level of the display change as follows:
Dimmer
Canceled
(Normal display)
22
1 2 3
4 5 6
8 9
0
+10
MUTING
Muting the
Sound
Changing
DIMMER
the Display
Brightness
RX-7030V
ONLY
Much dimmer

Using the Sleep Timer

Using the Sleep Timer, you can fall asleep while listening to music.
When the shut-off time comes, the receiver turns off automatically.
Press SLEEP repeatedly.
The SLEEP indicator lights up on the display, and the shut-off time
changes in 10 minutes intervals:
10 20 30 40
(Canceled)
0
To check or change the time remaining until the shut-off time:
Press SLEEP once.
The remaining time until the shut-off time appears in minutes.
• To change the shut-off time, press SLEEP repeatedly.
To cancel the Sleep Timer:
Press SLEEP repeatedly until "SLEEP 0min" appears on the display.
(The SLEEP indicator goes off.)
• Turning off the power also cancels the Sleep Timer.
Recording a source
For analog-to-analog recording
You can record any analog playback source onto the recording
components connected to the audio output jacks on the rear of
this unit at the same time.
For digital-to-digital recording
You can record the currently selected digital input source through
the receiver to a digital recording device connected to the
DIGITAL OUT terminal.
Notes:
• Analog-to-digital and digital-to-analog recordings are not
possible.
• The output volume level, Midnight Mode (see page 20), Bass
Boost (see the left column), Digital Equalization (see page 32),
Surround modes and DSP modes (see pages 34 to 39) cannot
affect the recording.
Basic adjustment auto memory
This receiver memorizes sound settings for each source—
• when you turn off the power,
• when you change the source, and
• when you assign the source name (see page 21).
When you change the source, the memorized settings for the
newly selected source are automatically recalled.
The following can be stored for each source:
• Analog/digital input mode (see pages 19 and 20)
• Input attenuator mode (see page 20)
• Analog Direct (see page 21)
• Digital Equalization (see page 32)
• Speaker channel output levels (see page 32)
• Surround and DSP mode selection (see pages 37 and 39)
• Bass Boost setting (see the left column)
Notes:
• If the source is FM or AM, you can assign a different setting for
each band.
• If you want to memorize the volume level with the above
settings, set One Touch Operation to "ON" (see page 30).
50 60 70 80 90