Sony DVP-F5 Service Manual page 88

QQ
3 7 63 1515 0
* Pressing the UP or DOWN key of the cursor key of the remote
control increments or decrements the binary number. At the
same time, value of the binary number is written in the
2
E PROM of the EVR IC.
* When the EVR value of each channel is changed, the change
of the setup can be confirmed on the display as follows. Set
the LINE selector switch to the LINE IN position. Connect
any video signal and change the setup value. Change of the
setup can be confirmed on the display.
* When you want to change the channel to be adjusted, press
the RIGHT or LEFT key of the cursor key. You can select
the next channel or previous channel. When you want to
select the desired channel, press the numeric key. You can
select the channel of the number that you have pressed.
* Pressing 8 (next) on the sub-menu advances the display to
the display of the next adjustment.
### EVR
# NTSC Adjustment
0. FLICKER 7 ch
1. TINT 6 ch
2. SHARPNESS 12 ch
3. COLOR 5 ch
4. (Prev)
2 PAL Adjustment
The PAL adjustment can be performed in the same manner as in the
previous section " 1 NTSC Adjustment". However, the following
TE
L 13942296513
display of the PAL sub-menu is different from that of NTSC.
### EVR
# PAL Adjustment
0. FLICKER 7 ch
1. NOLSE 6 ch
2. SHARPNESS 12 ch
3. COLOR 5 ch
4. (Prev)
This item is different from the display of the NTSC adjustment.
3 NTSC Default Setting
4 PAL Default Setting
The default values of the EVR can be written into the E
using the EVR main menu.
Press either 3 or 4 of the remote controller. The following
display appears and a question is asked if you want to set the default
2
value into E PROM or not.
Press ENTER to set the default value. Press the STOP key not
to set.
### EVR
# NTSC Default Set
www
Default Set?
Yes : ENTER / NO : STOP
http://cxema.ru
http://www.xiaoyu163.com
###
#
Exit : RETURN
###
#
←
Exit : RETURN
2
###
#
x ao
y
. i
Exit : RETURN
http://www.xiaoyu163.com
8
5 Copy NTSC → PAL
6 Copy PAL → NTSC
Press either 5 or 6 of the remote controller. The following
display appears and a question is asked if you want to copy the
setup values that are stored in the NTSC (or PAL) EVR to the address
2
of the E PROM where the PAL (or NTSC) setup values are stored
at present.
Press ENTER to copy. Press the STOP key not to copy.
###
Copy NTSC → PAL
#
Copy?
Yes : ENTER / NO : STOP
7 DUMP
Pressing the 7 key on the remote controller from the EVR main
menu shows the EVR values of both NTSC and PAL.
###
# EVR MEMORY DUMP
RGB AMP
BRIGHT
CONTRAST
Q Q
COM AMP
3 6 7
COLOR
TINT/NOISE
FLICKER
SUB_B
The display pages can be scrolled by pressed the RIGHT or LEFT
cursor key.
The next page will be as follows.
###
# EVR MEMORY DUMP
SUB_R
GAMMA0
GAMMA1
PROM
SHARPNESS
8 Change to NTSC
9 Change to PAL
Pressing the 8 numeric key of the remote controller changes the
u163
display to the NTSC EVR values Pressing the 9 numeric key of
the remote controller changes the display to the PAL EVR values.
Press RETURN to exit the menu.
6-10
2 9 9 4
EVR ###
#
Exit : RETURN
EVR ###
#
NTSC PAL
1 ch 60 60
2 ch CF CF
3 ch 71 71
4 ch 62 62
1 3 1 5 0 5 8 2 9
5 ch AO AO
6 ch A3 88
7 ch 96 96
8 ch 6C 6C
Turn Page : LR
Exit : RETURN
EVR ###
#
NTSC PAL
9 ch 89 89
10ch 36 36
11ch 6E 6E
12ch 87 87
Turn Page : LR
Exit : RETURN
m
co
.
2 8
9 9
9 4 2 8 9 9