Table of Contents
Advertisement
OPERATION
Figure 1
WARNING: This electric firebox must be properly installed
before it is used.
The unit can be controlled by either the manual controls which are
located on the upper right of the fireplace or the remote (Figure 13
& 14).
The fireplace is supplied with an IR multifunction remote control.
!
NOTE: To operate correctly, the remote control must be point-
ed towards the Floating Display
A .
Standby
Turns the unit On and Off.
→ Activated by pressing the Standby button on the remote or the
unit.
• The unit will turn on with the same functions that it was set to
when it was turned Off and the intake temperature will be indi-
cated on the Floating Display
!
NOTE: When any button is pressed the intake temperature will
be displayed on the Floating Display
B .
Flame Effects
Turns the flame effect On and Off.
→ Activated by pressing the
C .
Heat ON/OFF
Turns the heater On and Off.
→ Activated by pressing the
• Indicated by the
icon and the intake temperature being
displayed on the Floating Display
ing off.
!
NOTE: After the heater is switched off, there is a 60 second
fan delay, where the fan will continue running before turning off.
!
NOTE: The unit can be operated in Heat Only Mode. When
the unit is only running with the heater, the
ously be displayed on the Floating Display
!
NOTE: The heater may emit a slight, harmless odor when first
used. This odor is a normal condition caused by initial heating of
internal heater parts and will not occur again.
D & E .
Thermostat Controls
Adjusts the temperature set point to your individual requirements.
Once the desired set temperature is reached the heater will turn
off. The heater will cycle on and off to maintain the desired set
temperature. The default temperature setting is 72°F (22°C).
→ Adjusted by pressing the
A
C D E
Floating
Display
.
TM
.
TM
for 5 seconds.
TM
button on the remote.
button on the unit or the remote.
, for 5 seconds before turn-
TM
icon will continu-
.
TM
to decrease the set point and the
to increase the set point on the unit or the remote.
• The Floating Display
it is adjusted.
!
F
NOTE: Holding the
seconds, on the unit, will change the temperature from °C to °F, or
vice versa.
Disable Heat
If desired, depending on the season, the heater on the unit can be
disabled. The unit will operate in the same fashion, with remainder
of the controls.
TM
Pressing the
and
and holding for 2 seconds will disable and enable the heater.
!
NOTE: When the heater has been disabled and either the
or the
is pressed the Floating Display
F .
Color Themes
Different presets of ambient lighting color combinations contained
in the unit.
→ Changed by repeatedly pressing the corresponding button on
the remote or the unit.
• Cycles through the different preset ambient lighting settings of
the unit, this includes different combinations of colours of the
flame base and media lighting.
!
NOTE: The last theme of the cycle is a prism where the unit
cycles through a variety of colours. Pressing the
the cycling and holds the unit on the preferred color, indicated by
a "U" - Unfreeze or a "F" - Freeze on the display.
G .
Brightness
Changes the brightness of the lights in the unit.
→ Adjusted by repeatedly pressing the corresponding button on
the remote.
• Indicated by the second digit on the Floating Display™
changing to show: "H" (high), and "L" (low).
H .
Sleep Timer
The Sleep Timer can be set to automatically shut off the fireplace
after a preset time (from 30 minutes to 8 hours).
→ To set the timer press the timer button on the remote, repeat-
edly, until the desired time is displayed.
• The Floating Display
justed. Once the timer has begun, pressing the
display the time remaining before the unit turns Off.
!
NOTE: The Sleep Timer can be cancelled at any time by
pressing the
button repeatedly until the sleep timer displays
nothing.
Resetting the Temperature Cutoff Switch
Should the heater overheat, an automatic cut out will turn the
whole unit off and it will not come back on without being reset. It
can be reset by turning the power to the unit and waiting 5 min-
utes before turning the unit back on.
CAUTION: If you need to continuously reset the heater, un-
plug the unit and call technical support at 1-888-346-7539.
will indicate the temperature set point as
TM
and the
buttons down for two
buttons on the unit at the same time
TM
will display the different times as it is ad-
TM
will indicate "--".
button stops
button will
3
Advertisement
Table of Contents
