Test Mode - Kenwood DPX302 Service Manual

DPX302,DPX-MP2100
● How to enter the test mode
Press and hold the [1] and [3] keys and reset.
(While "– – – –" is being displayed, power can be ON for
30 minutes.)
● How to clear the test mode
Reset, momentary power down, Acc OFF, Power OFF.
● Test mode default condition
• Source is STANDBY.
• Display lights are all turned on.
• The volume is at -10dB (The display is 30).
• LOUD is OFF.
• CRSC is off regardless of the availability of switching
function.
• SYSTEM Q is NATURAL (=FLAT).
• BEEP is always activated by briefl y pressing a button.
• AUX is ON.
● Special display in tuner mode
Error is found in front-end, etc. if indications below are
displayed while in tuner mode.
"TNE2P_NG": Front-end E2PROM values are still default
(not determined).
"TNCON_NG": Cannot communicate with the front-end.
● K3I forced switching
Every time when [6] key is pressed in tuner FM mode,
switched in the following order: AUTO → Forced WIDE →
Forced MIDDLE → Forced NARROW → AUTO. Default
status is AUTO, and displayed as shown below.
AUTO: FM1_98.1A
Forced WIDE: FM1_98.1W
Forced MIDDLE: FM1_98.1M
Forced NARROW: FM1_98.1N
● CD receiver test mode specifi cation
• Display mode default setting shall be P-TIME.
• Jumps to the following tracks by pressing the [
No. 9 → No. 15 → No. 10 → No. 11 → No. 12 → No. 13 →
No. 22 → No. 14 → No. 9 (recursive)
Note that when playing a CD-DA disc and an MP3/WMA/
AAC disc with 8 fi les or less, the disc is played from the
1st track in the normal order.
• Pressing the [ ] key goes back by 1 track from the track
being played.
10

TEST MODE

• When playing an MP3/WMA/AAC disc, display the file
format before starting to play each fi le. ("MP3", "WMA",
"AAC")
• When CD is the source, press the [1] key briefl y to jump
to No. 28.
• When CD is the source, press the [2] key briefl y to jump
to No. 14.
• When CD is the source, press the [3] key briefl y to display
CD mechanism model name and the version. Press the
[3] key briefl y again to go back to the normal screen. (time
code display)
• When CD is the source, press the [6] key to jump to No.
15. At this time, the volume value is set to 25 (2V PRE).
● AUDIO adjust mode
• Press [AUD] key briefly to enter the audio adjustment
mode.
• Press the remote control [∗] key and [AUD] key to go into
the audio adjustment mode.
• Both AUDIO FUNCTION MODE and SETUP MODE
adjustment items are included.
• By pressing [AUD] or [FM] key briefly, switch the item
to be adjusted in the following order. (only in forward
rotation)
The default item shall be Fader, and then the item is
forwarded in the following order: Balance → Bass Level
→ Middle Level → Treble Level → HPF Front → HPF
Rear → LPF Sub Woofer. (thereafter arbitrary)
• Continuous forwarding by remote control is prohibited.
• Fader is adjusted by the VOL knob and [
in 3 steps: R15 ↔ 0 ↔ F15. (Default value: 0)
• Balance is adjusted by the VOL knob and [
in 3 steps: L15 ↔ 0 ↔ R15. (Default value: 0)
• Bass/Middle/Treble Level are adjusted by the VOL knob
] key.
and [ ] / [
value: 0)
• HPF Front / Rear is adjusted by the VOL knob and [
/ [ ] keys in 2 steps: Through ↔ 220Hz. (Default value:
Through)
• LPF Sub Woofer is adjusted by the VOL knob and [
/ [ ]] keys in 2 steps: 50Hz ↔ Through. (Default value:
Through)
6 6 8 0 : 0 1 2 3
Model name Version
] keys in 3 steps: -8 ↔ 0 ↔ +8. (Default
] / [ ] keys
] / [ ] keys
]
]