Version history Version Data Note V1.0 2013-10-8 First version V1.1 2013-10-11 Add chapter 3.6.4 Default Account for User V1.2 2013-11-21 Modify chapter 5.2 Hardware Interface...
1. Structure Introduction ① ES610 works with power line and I/O line ○ 2 ○ 1 ② USB port ③ Supply power port and I/O port ④ Dimension: 83mm*43.2mm*17.7mm I/O port Supply power port ○ 3 ○ 4...
2. Preparation Make sure the equipments below are all available. Equipment Lists: Equipment Name Number Note ES610 Necessary GSM SIM Card Necessary power Line Necessary I/O Line Necessary Power supply (12V- 36V) Necessary (Cigarette Lighter/ OBD) Data line Not Necessary (For AT command)
3. Quick Using Steps S: Success Step 1 F: Fail Insert SIM Card Step 2 Install ES610 Step 3 Power on F check, re-do AT or SMS Step 4 (SMS) Step 7 (AT) Set APN&IP Set APN,IP F check, re-do...
Open the terminal cover, and put the metal side of SIM card face down and then fasten the card slot cover. Note: SIM Hot-Plug is forbidden for this device. 1. Metal side faces 2. Fasten card slot 3.2 Step 2: Install ES610 The terminal is GPS positioning product, it is recommended that you follow the instructions to install.
I/O line Power supply line ④ 3.2.1 Connect Lines to ES610 First, connect power supply line to ES610. Plug the part ② of power supply line into ES610 power supply port (chapter 1 ③) Second, connect I/O line to ES610...
When finishing installation, as long as power supply line is connected with cigarette lighter or OBD, ES610 is powered on and starts work. Note: If ES610 is connected with cigarette lighter, then only the car is ignition on, cigarette lighter will has voltage. That means, ES610 can be powered on.
When ES610 is powered on, the two LEDs –Yellow and green LEDs will light for 10 seconds; then, only green LED will blink four times; after blinking, yellow and green LEDs will blink together. Wait for a while, yellow LED will light without blink.
Page 11
The reporting server is esky car online platform: www.eskylocate.com and the port is 1750. The default password is 000000 So the content of SMS should be: gprs,000000,cmnet,0, www.eskylocate.com:1750,120# Report server Password 1) The command possible responses: ①GPRS=Success! That means everything goes well.
Make sure GPS signal coverage is good. 3.5 Step 5: Query Current Location (SMS) If Step1 ~ Step 4 have passed, Then you can refer to <ES610 Protocol> to go on test other functions. The Query Current Location command is “Where, [PASSWORD] #”.
3.6 Step 6: Login Car Online Platform 3.6.1 Visit Car Online Platform Click: http://www.eskywireless.com.cn See Figure 1 Figure 1: Loading Page If you don’t see this page, please do: ①Check your Internet Connection. ②Check your operation system(No IOS). ③You don’t have install plug-in (sliverlight), Microsoft will give you the link of installation. If not, you have to install it by yourself: http://www.microsoft.com/getsilverlight/Get-Started/Install/Default.aspx 3.6.2 Login Page...
①Make sure IMEI is the exactly number you can see on the product label. Totally 15 numbers. And also it’s unique, so don’t register with using same IMEI. ②Table “Version”, please choose ES610. ③Make sure your E-mail address is correct. You can re-get your password via E-mail if you forgot...
After register successfully, return to Log-In page and enter the User Name and Password you just set. 3.6.4 Default Account for User eSky Wireless Inc. has an default account for user to experience the Car Online Platform. The default account: User name: esky Password: esky123456 You are welcome to use the above user name and password to register on our platform.
Figure 5: Main tracking Page 3.6.5 Modes Switch Page If you have two or more ES610 devices, you can add the others in one account (Same UserID). Click the middle of 3*3 squared. As shown in Figure 6. Figure 6: Modes Switch Page Then click “Add”...
If commands are set by AT command, please refer to <serial Readme> to install ES610 device driver and set hyper terminal. You can contact our technical support to ask for device driver and <serial Readme>. If everything is ready, then follow me to enjoy the AT command trip.
It means APN, server IP have changed successfully. ② OK GPRS=Fail! Try again Please don’t set any command within 1 ~ 2 min after ES610 is powered on. Mark sure GPRS command spells correctly. ③ ERROR Make sure that AT command mark spells correctly.
Page 20
AT command should be: cmd=interval,000000,120# Possible Response: ① OK INTE RVA L =Success! ② OK INTERVAL=Fail! ③ ERROR ④No Response.
4. Install and Operation 4.1 Installation Method Note: 1) The following installation order, please do not inverted. 2) During the installation process, please do not supply the terminal. The terminal installation is divided into hidden installation and open installation. When the terminal is using special vehicles, hidden installation is recommended. Otherwise, open installation is chosen.
4.3 Installation Notes ① Avoid put together with the emission source, for example, reversing radar, anti-theft devices and other on-board communications equipment. ② As for fixing the terminal, you can bound with ties or stick with wide sponge strength double-faced adhesive. ③...
**: When server is connected, the yellow light will on. When PDP is activated but no server connection, the yellow will blink every second. But if PDP cannot be activated, it shows off. 5.2 Hardware Interface ES610 has 3 INPUTs, 2 OUTPUTs. Definition Color...