Axis P13 SERIES Installation Manual
Hide thumbs
Also See for P13 SERIES:
- Installation manual (131 pages) ,
- User manual (63 pages) ,
- Datasheet (4 pages)
Related Manuals for Axis P13 SERIES
Summary of Contents for Axis P13 SERIES
- Page 1 AXIS P13 Series AXIS P1364 Network Camera AXIS P1365 Mk II Network Camera Installation Guide...
- Page 2 Low Voltage (LVD) Directive 2006/95/EC. See Safety Every care has been taken in the preparation of this on page 3 . document. Please inform your local Axis office of any • Restrictions of Hazardous Substances (RoHS) Directive inaccuracies or omissions. Axis Communications AB cannot 2011/65/EU.
- Page 3 • find answers to resolved problems in the FAQ database. てください。 Search by product, category, or phrase • report problems to Axis support staff by logging in to Korea your private support area 이 기기는 업무용(A급) 전자파적합기기로서 판매 • chat with Axis support staff 자...
-
Page 5: Hazard Levels
AXIS P13 Series Safety Information Read through this Installation Guide carefully before installing the product. Keep the Installation Guide for future reference. Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury. -
Page 6: Safety Instructions
Battery The Axis product uses a 3.0 V CR2032 lithium battery as the power supply for its internal real-time clock (RTC). Under normal conditions this battery will last for a minimum of five years. Low battery power affects the operation of the RTC, causing it to reset at every power-up. When the battery needs replacing, a log message will appear in the product’s server report. - Page 7 WARNING • Risk of explosion if the battery is incorrectly replaced. • Replace only with an identical battery or a battery which is recommended by Axis. • Dispose of used batteries according to local regulations or the battery manufacturer's instructions.
-
Page 9: Installation Steps
AXIS P13 Series Installation Guide This Installation Guide provides instructions for installing AXIS P1364 Network Camera or AXIS P1365 Mk II Network Camera on your network. For other aspects of using the product, see the User Manual available at www.axis.com Installation Steps 1. -
Page 10: Hardware Overview
AXIS P13 Series Hardware Overview Status LED Built-in microphone microSD card slot Audio in Audio out Network connector (PoE) Power LED Network LED Control button 10 I/O connector 11 Iris connector 12 Power connector (DC) 13 RS485/422 connector... -
Page 11: Led Indicators
AXIS P13 Series AXIS P1364 AXIS P1365 Mk II Focus ring Lock screw for focus ring Zoom puller LED Indicators Note • The Status LED can be configured to be unlit during normal operation. To configure, go to Setup > System Options > Ports & Devices > LED. See the online help for more information. -
Page 12: Status Led Behavior For Focus Assistant
AXIS P13 Series Power LED Indication Green Normal operation. Amber Flashes green/amber during firmware upgrade. Status LED Behavior for Focus Assistant The status LED flashes when the Focus Assistant is active. Indication Color The image is out of focus. Adjust the lens. - Page 13 SD card. Use your fingers to insert and remove the card. • Risk of data loss and corrupted recordings. Do not remove the SD card while the product is running. Disconnect power or unmount the SD card from the Axis product’s webpages before removal.
-
Page 14: Specifications
Enabling the Focus Assistant. Press and very quickly release the Control button. • Resetting the product to factory default settings. See page 20. • Connecting to an AXIS Video Hosting System service or AXIS Internet Dynamic DNS Service. For more information about these services, see the User Manual. Specifications Operating Conditions The Axis product is intended for indoor use. - Page 15 AXIS P13 Series Function Notes Specifications 0 V DC 0 V DC (-) DC output Can be used to power auxiliary equipment. 12 V DC Note: This pin can only be used as power out. Max load = 50 mA 3–...
- Page 16 AXIS P13 Series RS485/422 Connector Two 2-pin terminal blocks for RS485/RS422 serial interface. The serial port can be configured to support: • Two-wire RS485 half duplex • Four-wire RS485 full duplex • Two-wire RS422 simplex • Four-wire RS422 full duplex point to point...
-
Page 17: Install The Hardware
AXIS P13 Series Connection Diagrams I/O Connector 0 V DC (-) DC output 12 V, max 50 mA I/O configured as input I/O configured as output Install the Hardware NO TICE TICE TICE • Due to local regulations or the environmental and electrical conditions in which the product is to be used, a shielded network cable (STP) may be appropriate or required. -
Page 18: Access The Product
7. Aim the camera in the right direction and use the supplied Allen key to tighten the ball joint. Access the Product AXIS IP Utility and AXIS Camera Management are recommended methods for finding Axis products on the network and assigning them IP addresses in Windows®. Both applications are free and can be downloaded from www.axis.com/techsup The product can be used with most operating systems and browsers. -
Page 19: Adjust Focus With The Focus Assistant
• If movements in front of the camera cannot be avoided, the Focus Assistant should not be used. • If the control button is not released within two seconds, AXIS Internet Dynamic DNS Service is enabled instead of the Focus Assistant. -
Page 20: Reset To Factory Default Settings
For the latest version of this document, see www.axis.com The User Manual is available at www.axis.com Visit www.axis.com/techsup to check if there is updated firmware available for your network product. To see the currently installed firmware version, go to Setup > About. - Page 22 Installation Guide Ver. M4.4 AXIS P13 Series Date: February 2016 © Axis Communications AB, 2015 Part No. 1540127...