Using The Audio Settings - Onkyo HT-S5300 Instruction Manual

Note
"Power Control"
• The setting can be set only when the above
" "
HDMI Control setting is set to "On".
• HDMI power control only works with p-compatible
components that support it and may not work properly with
some components due to their settings or compatibility.
• When set to "On", power consumption will increase.
• When set to "On", regardless of whether the AV receiver is On
or in Standby, both audio and video stream from an HDMI input
will be output to the TV or other components via HDMI connec-
tion (HDMI pass through function). When the HDMI pass
through function activates in standby mode, HDMI THRU indi-
cator will light.
• The power consumption during standby mode will increase dur-
ing the HDMI pass through function; however in the following
cases, the power consumption can be saved:
1. The TV is in standby mode.
2. You are watching a TV program.
• Refer to the connected component's instruction manual for
details.
■
TV Control
Off:
TV Control disabled.
On:
TV Control enabled.
Set to "On" when you want to control the AV receiver
from an p-compatible TV that is connected to
HDMI.
Note
• Do not assign the component connected with the HDMI input to
the TV/CD selector when you set "TV Control" setting to "On".
Otherwise, appropriate CEC (Consumer Electronics Control)
operation is not guaranteed.
• Set to " Off " when the TV is not compatible or when it is unclear
whether the TV is compatible or not.
• The "TV Control" setting can be set only when the above
" " "Power Control"
HDMI Control and
to "On".
• Refer to the connected component's instruction manual for
details.
After changing the settings of the
"Audio Return Ch", "Power Control"
, turn off the power to all connected pieces of
trol"
equipment and then turn them on again. Refer to the
User's Manuals for all connected pieces of equipment.
settings are both set
HDMI Control ,
" "
, or "TV Con-

Using the Audio Settings

You can change various audio settings by pressing
AUDIO.
Note
These settings are disabled when:
• a pair of headphones is connected, or
• the "Audio TV OUT" setting is set to "On"
selector other than HDMI is selected.
1
Press RECEIVER followed by AUDIO.
2
Use q/w to select an item, and e/r to change the
setting.
Repeat this step for the other settings.
Tone Control Settings
You can adjust the bass and treble for the front speakers,
except when the Direct listening mode is selected.
■
Bass
–10 dB to 0 dB to +10 dB in 2 dB steps
You can boost or cut low-frequency sounds output
by the front speakers.
■
Treble
–10 dB to 0 dB to +10 dB in 2 dB steps
You can boost or cut high-frequency sounds output
by the front speakers.
Note
• To bypass the bass and treble tone circuits, select the Direct lis-
tening mode.
• This procedure can also be performed on the AV receiver by
using its TONE, –, and + buttons
Speaker Levels
You can adjust the volume of each speaker while listening
to an input source.
These temporary adjustments are cancelled when the AV
receiver is set to Standby. To save the setting you made
here, go to "Level Cal (Level Calibration)"
setting the AV receiver to Standby.
■
Subwoofer
–15 dB to 0 dB to +12 dB in 1 dB steps
■
Center
–12 dB to 0 dB to +12 dB in 1 dB steps
Note
• You cannot use this function while the AV receiver is muted.
• Speakers that are set to "No" or "None" in the "Sp Config
(Speaker Configuration)" (➔
(➔ 40) and an input
43).
(➔
(➔ 36) before
35) cannot be adjusted.
En
41