Audio Adjust - Onkyo HT-S5300 Instruction Manual

Sp Distance (Speaker Distance)
Menu
Here you can specify the distance from each speaker to the
listening position so that the sound from each speaker
arrives at the listener's ears as the sound designer
intended.
■
Unit
feet:
Distances can be set in feet. Range: 1ft to 30ft in
1 foot steps.
meters:
Distances can be set in meters. Range: 0.3m to 9.0m
in 0.3 meter steps.
(The default setting varies from country to country.)
■
Left, FrontHigh Left, Center, FrontHigh Right,
Right, Surround Right, SurrBack Right,
SurrBack Left, Surround Left, Subwoofer
Specify the distance from the each speaker to your lis-
tening position.
Note
• These settings are disabled when:
• a pair of headphones is connected, or
• the "Audio TV OUT" setting is set to "On"
input selector other than HDMI is selected.
• Speakers that you set to "No" or "None" in the "Sp Config
(Speaker Configuration)"
• The Center, Right, Subwoofer and Front High distances can be
set up to 5 ft. (1.5 m) more or less than the "Left" distance. For
example, if the "Left" distance is set to 20 ft. (6 m), the Center,
Right, Subwoofer, Front High Left and Front High Right dis-
tances can be set between 15 and 25 ft. (4.5 and 7.5 m).
• The Surround and Surround Back distances can be set up to 5 ft.
(1.5 m) more or 15 ft. (4.5 m) less than the "Left" distance. For
example, if the "Left" distance is set to 20 ft. (6 m), the Surr
Right, Surr Left, Surr Back R and Surr Back L distances can be
set between 5 and 25 ft. (1.5 and 7.5 m).
Level Cal (Level Calibration)
Menu
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
■
Left, FrontHigh Left, Center
Right, Surround Right, SurrBack Right,
SurrBack Left, Surround Left
–12 dB to 0 dB to +12 dB in 1 dB step.
■
Subwoofer *1
–15 dB to 0 dB to +12 dB in 1 dB step.
Note
• Speakers that you set to "No" or "None" in the "Sp Config
(Speaker Configuration)"
• The speakers cannot be calibrated while a pair of headphones is
connected or the AV receiver is muted or "Audio TV OUT" set-
ting is set to " On " (➔
*1 For the center speaker and subwoofer, the level settings made
En
by using AUDIO are saved.
36
Sp Distance
40) and an
(➔
(➔ 35) cannot be selected.
Level Cal
*1 , FrontHigh Right,
(➔ 35) cannot be selected.
40).
Tip
• If you're using a handheld sound level meter, adjust the level of
each speaker so that it reads 75 dB SPL at the listening position,
measured with C-weighting and slow reading.

Audio Adjust

Menu Audio Adjust
With the Audio Adjust functions and settings, you can
adjust the sound and listening modes as you like.
Multiplex/Mono Settings
Multiplex
This setting determines which channel of a stereo multi-
plex source is output. Use it to select audio channels or
languages with multiplex sources, multilingual TV broad-
casts, and so on.
■
Input Ch(Mux)
Main:
The main channel is output.
Sub:
The sub channel is output.
M/S:
Both the main and sub channels are output.
Mono
This setting specifies the channel to be used for playing
any 2-channel digital source such as Dolby Digital, or 2-
channel analog/PCM source in the Mono listening mode.
■
Input Ch(Mono)
L+R:
Both the left and right channels are output.
Left:
Only the left channel is output.
Right:
Only the right channel is output.
Dolby Settings
PLIIx Music (2ch Input)
These settings apply to only 2-channel stereo sources.
If you're not using any surround back speakers, these set-
tings apply to Dolby Pro Logic II, not Dolby Pro Logic
IIx.
■
Panorama
On:
Panorama function on.
Off:
Panorama function off.
With this setting, you can broaden the width of the front
stereo image when using the Dolby Pro Logic IIx Music
listening mode.