1. Manuals
  2. Brands
  3. SentexSystems Manuals
  4. Intercom System
  5. CROWN JEWEL
  6. Installation instructions manual

SentexSystems CROWN JEWEL Installation Instructions Manual

Telephone entry system
Hide thumbs Also See for CROWN JEWEL:
Table of Contents

Advertisement

Quick Links

C C C C
ROWN
ROWN
ROWN
ROWN
TELEPHONE ENTRY SYSTEM
TELEPHONE ENTRY SYSTEM
TELEPHONE ENTRY SYSTEM
TELEPHONE ENTRY SYSTEM
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
J J J J
EWEL
EWEL
EWEL
EWEL
Doc.. 6001145
Doc.. 6001145
Doc.. 6001145
Doc.. 6001145
Rev B
Rev B
Rev B
Rev B

Advertisement

Table of Contents
loading

Related Manuals for SentexSystems CROWN JEWEL

Summary of Contents for SentexSystems CROWN JEWEL

  • Page 1 Doc.. 6001145 Doc.. 6001145 Doc.. 6001145 Doc.. 6001145 Rev B Rev B Rev B Rev B C C C C J J J J ROWN ROWN EWEL EWEL ROWN ROWN EWEL EWEL TELEPHONE ENTRY SYSTEM TELEPHONE ENTRY SYSTEM TELEPHONE ENTRY SYSTEM TELEPHONE ENTRY SYSTEM INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS...

  • Page 3: Table Of Contents

    Sentex. This document contains information proprietary to Sentex and such information may not be distributed without prior written consent of Sentex. The software and firmware included in the Sentex Crown Jewel unit as they relate to this documentation are also protected by copyright and contain information proprietary to Sentex.
  • Page 4 Belden and Datalene are registered trademarks of the Belden Corporation. Page 2 of 22 Doc. 6001145 Rev B...

  • Page 5: Important Notices

    6. TRAIN YOUR CUSTOMER. The Crown Jewel is easy to operate when you take a few minutes to train the user, but untrained users can cause serious problems for you and for themselves.

  • Page 6: Part 1 Pulling Cables

    10 AWG B. SINGLE ENTRANCE CABLE REQUIREMENTS Figure 1. Single Entrance Cable Runs and Grounds. The following cables must be run to the main processor board in the Crown Jewel cabinet: • Main Processor Power: Run a 2-conductor cable from the outlet into which you will plug the Sentex supplied 12 VAC transformer (or the 12 VDC power supply you provide) to the Crown Jewel cabinet.

  • Page 7: Multiple Entrance Cable Requirements

    Run a 2-conductor cable from the outlet into which you will plug the Sentex supplied 12 VAC transformer (or the 12 VDC power supply you provide) to the Crown Jewel cabinet. See Table 2 above for the wire size required.

  • Page 8: Part 2 Mounting The Cabinet

    CAUTION The brass Crown Jewel cabinet is easily scratched. Use care when handling. Both the surface mount and flush-mount Crown Jewel cabinets are water-resistant, and may be located either indoors or outdoors. Mount the cabinet as follows: A. REMOVE THE FRONT PANEL ASSEMBLY Figure 2.

  • Page 9: Part 3 Wiringthe Unit

    PART 3 WIRING THE UNIT A. MAIN PROCESSOR BOARD CONNECTIONS Figure 4. Main Processor Board Connections. CAUTION Do not apply power to the unit until all other connections have been made. Damage to the unit may otherwise result. 1. GROUND THE CABINET in accordance with local code to a good earth/cold water ground nearby.
  • Page 10 The unit can also be powered by a 12 VDC power source, which also is connected to TB2. Polarity is unimportant for both AC and DC power. NOTE: The crown jewel will not charge a battery, so a UPS-type power supply must be used if a battery back-up is desired.

  • Page 11: Bypass Board Connections

    C. BYPASS BOARD CONNECTIONS The bypass board allows the Crown Jewel to be bypassed so normal telephone operation can be maintained in the event of a malfunction. 1. Standard Connection Figure 5. Bypass Board Hookup (Standard). Figure 6. Bypass Board Connections (Standard).
  • Page 12 Figure 8. Bypass Board Connections (with Alarm). IMPORTANT NOTE If the Crown Jewel will be used in conjunction with an alarm unit, it is imperative that the telephone line connect with the alarm unit first. If the units are not connected in this order, it will cause sporadic problems with both the alarm and the Crown Jewel unit (see Figure 6).
  • Page 13 3. Connect the last unit between the TELCO area on the bypass board and the incoming telephone line. • If multiple Crown Jewel’s (up to 7 can be used in one installation) are to be installed at the same site, the bypass boards must be installed in series. See Important Notes on next page.
  • Page 14 IMPORTANT NOTES • Whenever the Crown Jewel unit is in use, the Bypass switch must be set to the OPERATE position. • Should the Crown Jewel be disconnected for any reason, the Bypass switch must be set to BYPASS in order to maintain telephone service to the residence.

  • Page 15: Part 4 Installing Additional Features

    B. DOOR POSTION SENSING The Crown Jewel can monitor the position of one entrance (if relay 2 is not set as control) and react to a change in its status. For example, if an entrance is either pried open, or is held open more than a minute after its relay deactivates, the unit can: ♦...

  • Page 16: Remote Keypad

    ♦ The remote keypad installation requires a shielded 7 conductor, 18 to 24 AWG cable such as Belden Datalene #9932 or equivalent. 1. Connect one end of the cable to TB4 on the Crown Jewel’s main processor board (see Figure 11).

  • Page 17: Part 5 Testing And Adjusting The Unit

    PART 5 TESTING AND ADJUSTING THE UNIT After all connections have been made to the Crown Jewel unit, power can now be applied. The "POWER ON" indicator on the lower left of the main processor board should now be lit.
  • Page 18 For example, if you want a relay activation time of 35 seconds, at the programming prompt, enter "2435#". If the entry is accepted, the Crown Jewel will respond with two short beeps. 3. Exit the programming mode by pressing "00#". If the command is accepted, the Crown Jewel will respond with three short beeps.
  • Page 19 2. Press the "# " key on the Crown Jewel keypad. The telephone in the residence should ring. 3. Have someone answer the phone and dial a "9". The door/gate control relays should activate.
  • Page 20 1. On the Crown Jewel front panel keypad, enter " " and then the six digit programming access password. If the password is accepted, the Crown Jewel will respond with a programming promt consisting of two short beeps. 2. At the programming prompt, select step 38, the position of this unit in the chain, the total number of units in the chain, and the "#"...
  • Page 21 9. Complete the Installation Once you have finished testing and adjusting the Crown Jewel unit, your next step is to program the unit. For information regarding the programming of the Crown Jewel unit, refer to one of the two programming manuals were enclosed with this manual.

  • Page 22: Appendix 1 Installation Programming Menu

    Each programming command begins with a 2-digit step number, followed by the required data digits, and ended by the “#” key. • The step number tells the Crown Jewel which setting to change, and the digits contain the new value for that setting. •...

  • Page 23: Appendix 2 System Responses

    APPENDIX 2 SYSTEM RESPONSES The Crown Jewel emits various audio tones or beeps to respond to input or to indicate certain conditions. A list of the system’s audio responses are as follows: • 1 short beep - a key was pressed on main keypad •...

  • Page 24: Fcc Requirements

    FCC REQUIREMENTS The Crown Jewel system complies with Part 68 of the FCC Rules. The label affixed to this equipment contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide this information to your telephone company.

  • Page 25: Doc Requirements

    Load Numbers of all the devices does not exceed 100. The Load Number for the Crown Jewel unit is 3. Rev B Doc.

Table of Contents