Page 2
WARNING YOUR VEHICLE CAN BE HAZARDOUS TO OPERATE. A collision or rollover can occur quickly, even during routine maneuvers such as turning and driv- ing on hills or over obstacles, if you fail to take proper precautions. For your safety, understand and follow all the warnings contained in this Operator's Guide and the labels on your vehicle.
In Canada, products are distributed by Bombardier Recreational Products Inc. (BRP). In USA, products are distributed by BRP US Inc. The following trademarks are the property of Bombardier Recreational Prod- ucts Inc.: Can-Am™ Renegade™ Rotax ® XP-S™ TTI™ DESS™ ______________________...
Page 4
FOREWORD Congratulations on your purchase of a The information and components/ new Can-Am™ ATV. It is backed by the system descriptions contained in this BRP warranty and a network of autho- document are correct at the time of rized Can-Am dealers ready to provide publication.
TABLE OF CONTENTS While reading this Operator’s Guide, remember that: WARNING Indicates a potential hazard that, if not avoided, could result in serious in- jury or death. NOTICE................7 INTRODUCTION ..
Page 6
NOISE EMISSION CONTROL SYSTEM REGULATION ..... . . 61 EMISSION REQUIREMENTS ........... . . 62 BREAK-IN PERIOD.
Page 7
SPECIAL PROCEDURES ............86 Turn Over ..
Page 8
STORAGE AND PRESEASON PREPARATION ....... 121 WARRANTY BRP LIMITED WARRANTY NORTH AMERICA: 2007 CAN-AM ATV . .. 124 BRP INTERNATIONAL LIMITED WARRANTY: 2007 CAN-AM ATV .
NOTICE This Operator's Guide has been pre- pared to acquaint the owner/operator of a new vehicle with the various ve- hicle controls, maintenance and safe operating instructions. It is indispens- able for the proper use of the product. This Operator's Guide uses the follow- ing symbols.
INTRODUCTION Your dealer should have provided you The contents of this Operator's Guide with some basic information on the provide riding information which has particular controls and features of your been proven reliable by other users. new vehicle. Please take the time to They are not intended as a definitive study this Operator's Guide and all means of avoiding accidents.
Operator's Guide. instructor. Contact an authorized Always keep both hands on the Can-Am dealer for more informa- handlebars and both feet on the tions. footrests of the vehicle during op- USA and Canada Only: to find eration.
Page 13
Never operate this vehicle on hills Always use proper procedures if too steep for the vehicle or for your you stall or roll backwards when abilities. Practice on smaller hills climbing a hill. To avoid stalling, before attempting larger hills. use proper gear and maintain a steady speed when climbing a hill.
Page 14
Allow greater distance for braking. MORE INFORMATION ABOUT ATV SAFETY, contact an authorized Can-Am dealer to find out about available training courses nearest you. USA and Canada only: Call the Specialty Vehicle Institute of Amer-...
Beginning and inexperienced operators should complete a training course. They should then regularly practice the skills learned in the course and the operating techniques described in this Operator's Guide. For more information about the training course, contact an authorized Can-Am dealer. ____________ ___________ SAFETY INFORMATION...
Page 16
WARNING V00A01Q POTENTIAL HAZARD Failure to follow the age recommendations for this vehicle. WHAT CAN HAPPEN A lack of respect for this age recommendation can lead to severe injury or death of the child. Even though a child may be within the age group for which this vehicle is recommended, he may not have the skills, abilities, or judgment needed to operate this vehicle safely and may be involved in a serious accident.
Page 17
WARNING V00A02Q POTENTIAL HAZARD Carrying a passenger on this vehicle. WHAT CAN HAPPEN Greatly reduces your ability to balance and control this vehicle. Could cause an accident, resulting in harm to you and/or your passenger. HOW TO AVOID THE HAZARD Never carry passenger.
Page 18
WARNING V00A03Q POTENTIAL HAZARD Operating this vehicle on paved surfaces. WHAT CAN HAPPEN The tires are designed for off-road use only, not for use on pavement. Paved surfaces may seriously affect handling and control of this vehicle, and may cause the vehicle to go out of control. HOW TO AVOID THE HAZARD Never operate this vehicle on any paved surfaces, including sidewalks, driveways, parking lots and streets.
Page 19
WARNING V00A04Q POTENTIAL HAZARD Operating this vehicle on public streets, roads or highways. WHAT CAN HAPPEN You can collide with another vehicle. HOW TO AVOID THE HAZARD Never operate this vehicle on any public street, road or highway, even a dirt or gravel one.
Page 20
WARNING V00A06Q POTENTIAL HAZARD Riding this vehicle without wearing an approved helmet, eye protection and protective clothing. WHAT CAN HAPPEN The following items concern all ATV's operator: – riding without an approved helmet increases the chances of a severe head injury or death in the event of an accident –...
Page 21
WARNING V00A07Q POTENTIAL HAZARD Riding this vehicle after consuming alcohol or drugs. WHAT CAN HAPPEN Could seriously affect your judgment. Could cause you to react more slowly. Could affect your balance and perception. Could result in an accident or death. HOW TO AVOID THE HAZARD Never consume alcohol or drugs before or while riding this vehicle.
Page 22
WARNING V00A08Q POTENTIAL HAZARD Operating this vehicle at excessive speeds. WHAT CAN HAPPEN Increases your chances of losing control of the vehicle, which can result in an accident. HOW TO AVOID THE HAZARD Always travel at a speed which is proper for the terrain, visibility and op- erating conditions, and your experience.
Page 23
WARNING V00A09Q POTENTIAL HAZARD Attempting wheelies, jumps and other stunts. WHAT CAN HAPPEN Increases the chance of an accident, including an overturn. HOW TO AVOID THE HAZARD Never attempt stunts, such as wheelies or jumps. Do not try to show off. ____________ ___________ SAFETY INFORMATION...
Page 24
WARNING POTENTIAL HAZARD Failure to inspect the vehicle before operating. Failure to properly maintain the vehicle. WHAT CAN HAPPEN Increases the possibility of an accident or equipment damage. HOW TO AVOID THE HAZARD Always inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition.
Page 25
WARNING V00A0BQ POTENTIAL HAZARD Removing hands from handlebar or feet from the footrests during opera- tion. WHAT CAN HAPPEN Removing even one hand or foot can reduce your ability to control the vehicle or could cause you to lose your balance and fall off the vehicle. If you remove a foot from the footrests, your foot or leg may come into contact with the rear wheels, which could injure you or cause an accident.
Page 26
WARNING V00A0CQ POTENTIAL HAZARD Failure to use extra care when operating this vehicle on unfamiliar terrain. WHAT CAN HAPPEN You can come upon hidden rocks, bumps, or holes, without enough time to react. Could result in the vehicle overturning or loss of control. HOW TO AVOID THE HAZARD Go slowly and be extra careful when operating on unfamiliar terrain.
Page 27
WARNING V00A0DQ POTENTIAL HAZARD Failure to use extra care when operating on excessively rough, slippery or loose terrain. WHAT CAN HAPPEN Could cause loss of traction or vehicle control, which could result in an accident, including an overturn. HOW TO AVOID THE HAZARD Do not operate on excessively rough, slippery or loose terrain until you have learned and practiced the skills necessary to control this vehicle on such terrain.
Page 28
WARNING V00A0EQ POTENTIAL HAZARD Turning improperly. WHAT CAN HAPPEN Vehicle could go out of control, causing a collision or overturn. HOW TO AVOID THE HAZARD Always follow proper procedures for turning as described further in this Operator's Guide. Practice turning at low speeds before attempting to turn at faster speeds.
Page 29
WARNING V00A0QQ POTENTIAL HAZARD Operating on excessively steep hills. WHAT CAN HAPPEN The vehicle can overturn more easily on extremely steep hills than on level surfaces or small hills. HOW TO AVOID THE HAZARD Never operate this vehicle on hills too steep for the vehicle or for your abil- ities.
Page 30
WARNING V00A0FQ POTENTIAL HAZARD Climbing hills improperly. WHAT CAN HAPPEN Could cause loss of control or cause vehicle to overturn. HOW TO AVOID THE HAZARD Always follow proper procedures for climbing hills as described further in this Operator's Guide. Always check the terrain carefully before you start up any hill. Never climb hills with excessively slippery or loose surfaces.
Page 31
WARNING V00A0GQ POTENTIAL HAZARD Going down a hill improperly. WHAT CAN HAPPEN Could cause loss of control or cause vehicle to overturn. HOW TO AVOID THE HAZARD Always follow proper procedures for going down hills as described further in this Operator's Guide. NOTE: A special technique is required when brak- ing as you go down a hill.
Page 32
WARNING V00A0HQ POTENTIAL HAZARD Improperly crossing hills or turning on hills. WHAT CAN HAPPEN Could cause loss of control or cause vehicle to overturn. HOW TO AVOID THE HAZARD Never attempt to turn the vehicle around on any hill until you have mas- tered the turning technique as described further in this Operator's Guide on level ground.
Page 33
WARNING V00A0IQ POTENTIAL HAZARD Stalling, rolling backwards or improperly dismounting while climbing a hill. WHAT CAN HAPPEN Could result in vehicle overturning. HOW TO AVOID THE HAZARD Use proper gear and maintain steady speed when climbing a hill. If you lose all forward speed: Keep your weight uphill.
Page 34
WARNING V00A0JQ POTENTIAL HAZARD Improperly operating over obstacles. WHAT CAN HAPPEN Could cause loss of control or a collision. Could cause the vehicle to overturn. HOW TO AVOID THE HAZARD Before operating in a new area, check for obstacles. Never attempt to ride over large obstacles, such as large rocks or fallen trees.
Page 35
WARNING V00A0KQ POTENTIAL HAZARD Skidding or sliding improperly. WHAT CAN HAPPEN You may lose control of this vehicle. You may also regain traction unexpectedly, which may cause the vehicle to overturn. HOW TO AVOID THE HAZARD Learn to safely control skidding or sliding by practicing at low speeds and on level smooth terrain.
Page 36
WARNING V00A0LQ POTENTIAL HAZARD Operating this vehicle through deep or fast flowing water. WHAT CAN HAPPEN Tires may float, causing loss of traction and loss of control, which could lead to an accident. HOW TO AVOID THE HAZARD Never operate this vehicle in fast flowing water or in water deeper than that specified further in this Operator's Guide.
Page 37
WARNING V00A0MQ POTENTIAL HAZARD Improperly operating in reverse. WHAT CAN HAPPEN You could hit an obstacle or person behind the vehicle, resulting in serious injury. HOW TO AVOID THE HAZARD When you select reverse gear, make sure there are no obstacles or people behind the vehicle.
Page 38
WARNING V00A0OQ POTENTIAL HAZARD Operating this vehicle with improper tires, or with improper or uneven tire pressure. WHAT CAN HAPPEN Use of improper tires on this vehicle, or operation of this vehicle with im- proper or uneven tire pressure, may cause loss of control, tire blow outs, tire to move around on its rim and increases the risk of an accident.
Page 39
All parts and accessories added to this vehicle should be approved by BRP and should be installed and used according to instructions. If you have questions, consult an authorized Can-Am dealer. NEVER install passenger seat or use the cargo area to carry a passenger.
Page 40
WARNING V00A0PQ POTENTIAL HAZARD Overloading this vehicle or carrying or towing cargo improperly. WHAT CAN HAPPEN Could cause changes in vehicle handling which could lead to an accident. HOW TO AVOID THE HAZARD Never exceed the stated load capacity for this vehicle including operator, as well as other loads and added accessories.
Page 41
WARNING V03M01Q POTENTIAL HAZARD Transporting flammable or dangerous material can lead to explosions. WHAT CAN HAPPEN This can cause serious injury or death. HOW TO AVOID THE HAZARD Never transport flammable or dangerous material. While reading this Operator’s Guide, remember that: WARNING Indicates a potential hazard that, if not avoided, could result in serious in- jury or death.
ATV clubs, a recognized ATV train- Each will ride and handle differently. ing organization or contact an autho- Never assume that the vehicle will go rized Can-Am dealer. everywhere safely. Sudden changes USA and Canada Only: to find out in terrain caused by holes, depres- about available training course nearest sions, banks, softer or harder "ground"...
Correct any problem you may have Before using this vehicle, the operator found before riding. See an autho- should always: rized Can-Am dealer as necessary. • Apply parking brake and check if it operates properly. • Check tire pressure and condition.
Clothing Actual weather conditions should help you decide how to dress. However, it is important that the operator always wear the appropriate protective clothing and apparel, including an approved helmet, eye protection, boots, gloves, long sleeved shirt and pants. This type of clothing will provide you protection from some of the minor hazards you may encounter en route.
Your vehicle can help you perform a number of different LIGHT tasks ranging from snow removal to pulling wood or carrying cargo. A variety of accessories are available from your authorized Can-Am dealer. However, always respect the load and capacities of the vehicle. Overloading of the vehicle can overstress the components and cause failure.
Recreational Riding Respect the rights and limitations of others. Stay away from areas designated for other types of off road use. This includes snowmobile trails, equestrian trails, cross country ski trails, mountain bike trails, etc. Never assume there are no other users on the trail.
Design Limitation Although the vehicle is exceptionally rugged for its class, it is still a light vehicle by definition and its operation must be restricted to its proper purpose. The addition of weight to any part of the vehicle changes its gravitational stability and modifies its performance.
Uphill Driving Due to configuration, this vehicle has excellent climbing ability, so much so that tipover is possible before traction is lost. For example, it is common to encounter terrain situations where the top of the hill has eroded to a point that the hill peak rises very sharply.
Riding Techniques Riding your vehicle too fast for the conditions may result in injury. Apply only enough throttle to proceed safely. Statistics show that high speed turns usually result in mishaps and injury. Always remember that this vehicle is heavy! Its pure weight alone may entrap you should it fall and pin you down.
Page 50
This vehicle is not designed for riding on roads or highways. In most places it is an illegal practice. Riding your vehicle on roads or highways could cause a collision to occur with another vehicle. The tires of this vehicle are not suited for paved road use.
Page 51
If your trip crosses frozen waterways, make sure that the ice is thick enough and sound enough to support the total weight of yourself, the vehicle and its load. Be ever watchful of open water... it is a sure indication that the ice thickness will vary.
Page 52
Respect and follow all posted trail signs. They are there to help you and others. Obstacles in the "trail" should be traversed with caution. This includes loose rocks, fallen trees, slippery surfaces, fences, posts, and embankments and de- pressions. You should avoid them whenever possible. Remember that some obstacles are too large or dangerous to cross and should be avoided.
Page 53
Downhill Keep your body weight rearwards. Apply the brake gradually to prevent skidding. Do not "coast" down the slope using solely engine compression or in neutral gear. V00A0YL While reading this Operator’s Guide, remember that: WARNING Indicates a potential hazard that, if not avoided, could result in serious in- jury or death.
Page 54
Side Hilling This is one of the most risky types of riding since it may drastically change the balance of the vehicle. It should be avoided wherever possible. If it is necessary to do so however, it is important that you ALWAYS keep your body weight on the upside of the slope...
Part of your responsibility towards safety is to respect the contents of this Op- erator's Guide. It provides valuable advice on how to properly take care of your vehicle. If further assistance is required your authorized Can-Am dealer is always willing to help.
HANG TAG This vehicle comes with a hang tag and labels containing important safety infor- mation. Any person who rides this vehicle should read and understand this information before riding. V02M0FL USA and Canada Only 704901107 vmo2006-005-009_en ___________ ___________ SAFETY INFORMATION...
The following labels are on your vehicle and they should be considered perma- nent parts of the vehicle. If missing or damaged, they can be replaced free of charge. See an authorized Can-Am dealer. NOTE: The following illustrations used in this Operator's Guide are a general representation only.
Page 59
Label 6 Label 8 vmo2007-015-019_en Label 7 XXXX XXXXX.XXXXXX XXXXXXXXXXXXXX XXXXXXXXX vmo2006-014-003_a XXXX INTERNATIONAL MODELS ONLY XXXX Label 9 vmo2007-002-002 NEVER carry a passenger on this cargo area MAXIMUM REAR LOAD : XX lb (XX kg) evenly distributed. LOCATED UNDER SEAT ON THE UPPER BAR OF FRAME 704 901 333 vmo2007-015-020_en...
NOISE EMISSION CONTROL SYSTEM REGULATION USA and Canada Only Tampering with Noise Control System Is Prohibited! U.S. Federal law and Canadian provincial laws may prohibit the following acts or the causing there of: 1. The removal or rendering inoperative by any person other than for purposes of maintenance, repair or replacement of any device or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or...
EMISSION REQUIREMENTS USA Only The California Air Resources Board (CARB) requires that your vehicle comply with applicable exhaust emissions standards during its useful life, when operated and maintained according to the instructions supplied. A non-compliance Red Label (as well as a Green Label) is obtained annually during California Vehicle registration.
(185 mi) or 30 days after the pur- chase, whichever comes first, your vehicle be inspected by an authorized Can-Am dealer. This inspection will give you the opportunity to discuss the unanswered questions you may have encountered during the first hours of operation.
CONTROLS/INSTRUMENTS/EQUIPMENT NOTE: Some controls/instruments/equipment are optional. vmo2007-015-016_a vdd2007-001-024_a vdd2007-001-022_b ______________________...
While reading this Operator’s Guide, remember that: WARNING Indicates a potential hazard that, if not avoided, could result in serious in- jury or death. NOTE: This section gives basic func- tions of the various controls of your ve- hicle. For more details of how to op- erate one control in conjunction with some others, refer to OPERATING IN- STRUCTIONS further in this section.
V07K01Y TYPICAL 1. Brake lever V07K02Y 2. To apply brakes TYPICAL 4) Parking Brake 1. Brake lever lock 2. Press to apply parking brakes When applied, it prevents the vehicle from moving. Useful when the brake To release mechanism: Squeeze needs to be locked for example when brake lever.
CAUTION: Always completely stop the vehicle and apply the brake prior to moving the transmission lever. P: Park This position locks the transmission to help prevent vehicle movement. Al- ways use when the vehicle is not in operation. In some circumstances, it may be necessary to rock the vehicle back and forth to move the gears in the transmission to allow the park to...
Page 70
Engine Start Button To start engine, place the engine stop switch to RUN. Press and hold the engine start button. Release immediately after engine is started. vmo2007-015-008_a IGNITION SWITCH POSITIONS 1. OFF 2. ON "with light" 3. ON "without light" Engine Stop Switch This switch can be used to stop engine and as an emergency control.
Unit Selection (MPH vs km/h) The speedometer, odometer and trip meter are factory preset in miles but it is possible to change them to kilo- vmr2007-050-002_g meter reading. Contact an authorized 1. Vehicle speed Can-Am dealer. 2. Engine RPM _____________________...
Page 72
Multifunction Display Hour Meter (trip time) (temporary display mode) The hour meter records vehicle run- Press and release selector button to ning time when the electrical system change the normal display mode to the is activated. It can be used to es- following temporary mode: tablish traveling time between 2 way points for instance.
Page 73
Can-Am dealer. Do not use the vehicle until repaired. CAUTION: If the light does not turn off right after engine starting, stop engine. See an authorized Can-Am dealer. Do not use the vehicle until re- paired. Message must be erased by an authorized Can-Am dealer.
Page 74
When this indicator is ON, it munication error. Contact an autho- indicates the 4WD system is rized Can-Am dealer. activated. When this indicator is ON, Fuel Level Display it indicates that there is only...
You can buy an additional igni- tion key and have it programmed for your vehicle. To have additional ignition key, refer to an authorized Can-Am dealer. 10) Fuel Tank Cap CAUTION: Never place anything over fuel tank cap because the vent...
12) Footpeg WARNING Use this area to keep your feet stable. Always stop engine before re- fueling. Open cap slowly. If a differential pressure condition is noticed (whistling sound heard when loosening fuel tank cap) have vehicle inspected and/or re- paired before further operation.
This panel allows an easier access to the service compartment. The ser- vice compartment contains different maintenance items like rear brake fluid reservoir, radiator cap, coolant reservoir and fuse holders. 14) Rear Storage Compartment vmr2007-059-001_a Convenient location to carry person- 1.
16) Rear Cargo Area To remove the radiator cap, press and turn it counterclockwise. Reverse the Convenient location to carry small arti- removal procedure to install. cles. Secure articles to rear fender by using the plastic eyelets provided. vmr2007-059-006_b TYPICAL 1.
vmr2007-059-004_d 1. Dipstick vmo2006-007-031_a Refer to LIQUID to check the engine TYPICAL — REAR FUSES LOCATION oil level correctly. 1. (F8) Main (30 A) (F9) Main accessories (30 A) 22) Brake Lever Fluid 20) Tool Kit Reservoir The tool kit is located in the rear stor- Located above front brake lever on the age compartment.
24) Engine Coolant Reservoir Located in service compartment un- derneath central panel. vmr2007-059-006_c 1. Coolant reservoir ______________________...
LIQUIDS While reading this Operator’s Guide, remember that: WARNING Indicates a potential hazard that, if not avoided, could result in serious in- jury or death. NOTE: This section specifies the rec- Fuel Level ommended liquids and procedures to WARNING check their levels. Refer to MAINTE- NANCE for procedures to replace the Always stop engine before refu- liquids.
Page 82
Oil Viscosity SAE 5W30 mineral-based oil is recom- mended for all seasons. However, during the hottest days of the summer the BRP XP-S 10W40 mineral oil (P/N 219 700 346) can be used. NOTE: For improved overall perfor- mance and all season applications, vmr2007-059-004_d use XP-S 5W40 synthetic oil (P/N 293 RH SIDE OF ENGINE...
Add a small amount of recommended To change gearbox oil, refer to MAIN- oil and recheck oil level. TENANCE section. Repeat the above procedures until Engine Coolant oil level reaches the dipstick's upper mark. Do not overfill. Recommended Coolant Properly tighten dipstick. Always use ethylene-glycol antifreeze containing corrosion inhibitors specifi- Gearbox Oil...
V07K0AA tion of leaks or engine problems. See Turn steering in the straight-ahead an authorized Can-Am dealer. position to ensure reservoir is level. Check the brake fluid level, the reser- Coolant Replacement voir is full when the fluid reaches of Refer to MAINTENANCE section.
Correct any problem you may have • Check tire pressure and condition. found before riding. See an autho- • Check wheels and bearings for rized Can-Am dealer as necessary. wear and damage. • Check location of controls and en- sure they work properly.
Starting the Engine Using the Reverse Insert key in ignition switch and turn to CAUTION: When changing from ON position. forward to reverse, or vice-versa, always completely stop the vehicle Place the engine stop switch to RUN. and apply the brake prior to moving Press the engine start button and hold the transmission lever.
Stopping the Engine The 4WD mode is engaged when the selector is pushed downwards. WARNING Avoid parking on slope. Release throttle and completely stop the vehicle. Apply the parking brake. Set transmission lever in PARK posi- tion. Push the engine stop switch in OFF position.
Before starting engine, check engine oil level and refill if necessary. If the oil pressure light stays ON after starting engine, stop engine and see an autho- rized Can-Am dealer as soon as possi- ble. Vehicle Immersion Should the vehicle become immersed,...
CARGO AND TRANSPORTATION While reading this Operator’s Guide, remember that: WARNING Indicates a potential hazard that, if not avoided, could result in serious in- jury or death. Cargo Transportation When transporting a vehicle, secure WARNING vehicle to trailer or in pickup box with suitable tie-downs.
Page 90
Front Location vmr2007-059-005_b Rear Location vmr2007-059-008_c WARNING Do not tow this vehicle behind a car or other vehicle. Use a trailer. ______________________...
• Install new spark plugs if possible or clean and dry spark plugs. • Start engine as explained above. If engine continues to flood, see an authorized Can-Am dealer. NOTE: Make sure to verify that there is no fuel i n engine oil, if so, replace engine oil.
Page 92
– Start engine with spark plug grounded to the engine away from spark plug hole. If no spark appears, replace spark plug. – If trouble persists, contact an authorized Can-Am dealer. 4. Speedometer CHECK ENGINE indicator lamp is on and multifunction dis- play shows CHECK ENGINE.
Page 93
6. Engine is under a protection mode. – Ckeck speedometer multifunction display for messages. – Speedometer CHECK ENGINE indicator lamp is on and multifunction dis- play shows CHECK ENGINE or LIMP HOME, contact an authorized Can-Am dealer. ENGINE BACKFIRE 1. Exhaust system leakage.
Page 94
– Rock the vehicle back and forth to move the gears in the transmission and allow the transmission lever to be set. 2. CVT dirty or worn-out. – Contact an authorized Can-Am dealer. THE RPM INCREASES BUT THE VEHICLE DOES NOT MOVE 1. The transmission is on PARK or NEUTRAL position.
SPECIFICATIONS VEHICLE MODEL RENEGADE ENGINE 4-stroke, V-twin, liquid cooled, Type 4-valves SOHC Number of cylinder 8 valves with mechanical lifters Number of valves (adjustable) Displacement 800 cc (48.82 cu. in) Bore 91 mm (3.58 in) Stroke 61.5 mm (2.42 in) Compression ratio 10.3:1...
Page 96
VEHICLE MODEL RENEGADE ELECTRICAL (cont'd) Make Type Spark plug DCPR8E 0.6 to 0.7 mm (.024 to .027 in) Number of spark plug Type Dry type battery Battery Volt 12 volts, 18 A•h Electric start. Start on P, R, N, H or...
Page 97
VEHICLE MODEL RENEGADE TIRES Make/Type Carlisle Hole Shot ATR/Radial 34.5 kPa (5 PSI) maximum Front Up to 31 kPa (4.5 PSI) minimum Pressure 141 kg 34.5 kPa (5 PSI) maximum (310 lb) Rear 31 kPa (4.5 PSI) minimum Front 25 x 8 x 12...
Page 98
VEHICLE MODEL RENEGADE LIQUIDS AND GREASES SAE 5W30 API Engine oil type classification SM, SL or SJ. Refer to OIL VISCOSITY CHART Gearbox oil type XP-S synthetic chaincase oil Ethylene-glycol/water mix (50% coolant, 50% distilled water). Use BRP Coolant premixed coolant or a coolant specially...
Can-Am dealer. PERIODIC MAINTENANCE CHART INITIAL INSPECTION 10 H OR 30 DAYS OR 300 km (185 mi) (To be performed by an authorized Can-Am dealer. The initial maintenance is very important and must not be neglected.) A: ADJUST...
Page 101
PERIODIC MAINTENANCE CHART INITIAL INSPECTION 10 H OR 30 DAYS OR 300 km (185 mi) (To be performed by an authorized Can-Am dealer. The initial maintenance is very important and must not be neglected.) A: ADJUST 25 H OR 750 km (470 mi)
Page 102
PERIODIC MAINTENANCE CHART INITIAL INSPECTION 10 H OR 30 DAYS OR 300 km (185 mi) (To be performed by an authorized Can-Am dealer. The initial maintenance is very important and must not be neglected.) A: ADJUST 25 H OR 750 km (470 mi)
Page 103
PERIODIC MAINTENANCE CHART INITIAL INSPECTION 10 H OR 30 DAYS OR 300 km (185 mi) (To be performed by an authorized Can-Am dealer. The initial maintenance is very important and must not be neglected.) A: ADJUST 25 H OR 750 km (470 mi)
Other items found in MAINTENANCE CHART must be performed by an authorized Can-Am dealer. NOTE: Among other things, this sec- tion gives the procedures to replace the liquids. Refer to LIQUIDS for pro- cedures to check levels and refill.
ENGINE Oil Change and Oil Filter Replacement Oil and filter are to be replaced at the same time. Oil change should be done with a warm engine. WARNING The engine oil can be very hot. In order to avoid potential burns, do not remove the engine drain plug vmo2006-007-020_a or the filter cover if the engine is...
Pinch hose between radiator and ther- mostat housing with a large hose pincher (P/N 529 032 500) or an equiv- alent. CAUTION: Do not use vise-grip pli- ers to pinch hose. vmr2007-059-006_b 1. Radiator cap Unscrew the coolant drain plug and drain the coolant into a suitable con- tainer.
Drive Belt Remove seat and central panel. Release clamps and remove air filter See an authorized Can-Am dealer to box cover. check the width and the condition of drive belt. CVT Cover Drain Screw Any time you suspect that water has entered the CVT cover, drain the CVT housing by removing the drain screw.
LOW PRESSURE ONLY, NEVER USE carbon out of the muffler. A HIGH PRESSURE WASHER. Stop engine and allow muffler to cool. See an authorized Can-Am dealer to check the performance of the cooling Reinstall the cleanout plug. system. Radiator Periodically check the radiator area for cleanliness.
GEARBOX Oil Change Place the vehicle on a level surface. Clean drain plug area and oil level plug then remove the gearbox drain plug. vmo2006-007-018_a 1. Oil level plug 2. Oil drain plug NOTE: To completely drain the gear- box, place a jack under the left footrest and tilt the vehicle toward the right side.
FUEL SYSTEM Throttle Cable Lubrication Lubrication The throttle cable must be lubricated with silicone lubricant (P/N 293 600 041) or an equivalent. WARNING Always use a silicone-based lubri- cant. Using another lubricant (like a water-based lubricant) could V07I0GY cause the throttle lever/cable stick- 1.
V07I0JY TYPICAL V07I0IY NOTE: Place a rag around the throttle Remove the throttle body side cover. cable adjuster to prevent the lubricant from splashing. Add lubricant until it runs out at throttle body end of the throttle cable. Reinstall and adjust the cable. Throttle Lever Adjustment Slide rubber protector back to expose throttle cable adjuster.
Page 112
V07I010 TYPICAL 1. Throttle lever A. 3 to 6 mm (1/8 to 7/32 in) With the transmission lever on PARK position, start the engine. Check if the throttle cable is adjusted correctly by turning handlebar fully right then ful- ly left. If the engine RPM increases, readjust the throttle lever free play.
ELECTRICAL WARNING Unless otherwise indicated, al- ways turn ignition switch to the OFF position before performing any maintenance or repair on elec- trical system. Spark Plug Removal vmo2006-007-030_a LH SIDE — FRONT CYLINDER Remove side panels. 1. Spark plug Unplug spark plug cables. Installation Unscrew spark plugs one turn.
Fuses WARNING Always respect this order for dis- WARNING assembly; disconnect BLACK (-) Always turn the ignition switch to cable first. OFF position before replacing a de- fective fuse. Unfasten retaining rod. If a fuse is damaged, replace it by one of the same rating.
Headlamps CAUTION: Never touch glass por- tion of an halogen bulb with bare fingers, it shortens its operating life. If glass is touched, clean it with isopropyl alcohol which will not leave a film on the bulb. To replace the headlamp bulb, proceed as follows.
Page 116
vmo2007-015-010_b 1. Lens vmr2007-050-008_a 2. Screws Push the bulb in and hold while turning Properly reinstall removed parts in the counterclockwise to release. reverse order of their removal. Install the new bulb by first pushing in Validate headlamp operation. while turning clockwise. Beam Aiming Adjustment Speedometer Adjust beam aiming as follows:...
Wheel Bearing Condition Push and pull the wheels from the up- per edge to feel the play. See an au- thorized Can-Am dealer if there is any play. vmo2007-015-013_a FRONT OF VEHICLE 1. Drive shaft protector 2.
Tires/Wheels TIRE PRESSURE FRONT REAR WARNING UP to 34.5 kPa 34.5 kPa When the tires are replaced, nev- MAX. 141 kg (5 PSI) (5 PSI) er install a bias tire with a radial (310 lb) tire. Such a combination could 31 kPa 31 kPa MIN.
Page 119
vmo2007-015-014_a TIGHTENING SEQUENCE CAUTION: Always use the recom- mended wheel nuts (P/N 250 100 082). Using a different nut could cause damages to the rim. _____________________...
See an authorized Can-Am dealer as necessary. Trailing Arms Check trailing arms for distortion, cracks or bending. See an authorized V07J01Y Can-Am dealer if any problem is de- tected. TYPICAL — REAR SHOCKS 1. Adjusting cams A-Arms 2. Smooth adjustment 3.
Rear disc 4.3 mm (.170 in) thickness Maximum discs 0.3 mm (.010 in) warpage See your authorized Can-Am dealer if a problem is detected concerning the brake system. Brake Fluid Replacement WARNING The brake fluid replacement or any brake system repairs should be performed by an authorized Can-Am dealer.
Remove seat and check latch mecha- and leaks. Ensure all hose clamps nism and pin for wear. See an autho- are properly secured and no hose is rized Can-Am dealer for parts replace- cracked, kinked or otherwise dam- ment if damaged. aged.
CHART. When a vehicle is not in use for more than one month, proper storage is a necessity. See an authorized Can-Am dealer for proper procedures. When using your vehicle after storage, a preparation is required. See an au- thorized Can-Am dealer for proper pro- cedures.
All genuine Can-Am ATV parts and accessories, installed by an authorized BRP dealer (as hereinafter defined) at the time of delivery of the 2007 Can-Am ATV, carry the same warranty as that of the Can-Am ATV. Your 2007 Can-Am Renegade 800 ATV is originally equipped with Carlisle †...
Page 127
SIX (6) CONSECUTIVE MONTHS, for private use or commercial use owners. The emission-related components included in the chart below, that are installed on EPA certified Can-Am ATVs (see list below) registered in the USA are covered for thirty (30) consecutive months.
Page 128
This warranty coverage is available only if each of the following conditions has been fulfilled: • The 2007 Can-Am ATV must be purchased as new and unused by its first owner from a BRP dealer authorized to distribute Can-Am ATVs in the country in which the sale occurred (“BRP dealer”);...
Page 129
If the issue has not yet been resolved, please submit your complaint in writing or call the appropriate number below: IN CANADA IN USA BOMBARDIER RECREATIONAL BRP US Inc. CAN-AM ATV PRODUCTS INC. CAN-AM ATV Consumer Services Group Consumer Services Group 7575 BOMBARDIER COURT...
Can-Am distributor/dealer (as hereinafter defined) at the time of delivery of the 2007 Can-Am ATV, carry the same warranty as that of the Can-Am ATV. Use of the product for racing or any other competitive activity, at any point, even by a previous owner will render this warranty null and void.
Page 131
This warranty coverage is available only if each of the following conditions has been fulfilled: • The 2007 Can-Am ATV must be purchased as new and unused by its first owner from a Can-Am distributor/dealer authorized to distribute Can-Am ATVs in the country in which the sale occurred (“Can-Am distributor/dealer”);...
Page 132
BRP’s obligations under this warranty are limited to, at its sole discretion, repair- ing parts found defective under normal use, maintenance and service; or replac- ing such parts with new genuine Can-Am ATV parts without charge for parts and labour, at any authorized Can-Am distributor/dealer.
Page 133
For countries within Europe, Middle East, Africa, Russia & CIS, please contact our European office: BRP EUROPE N.V. Consumer Service Center SKALDENSTRAAT 125 9042 GENT Belgium Tel.: + 32-9-218-26-00 For Scandinavian countries, please contact our Finland office: BRP FINLAND OY Service Department Ahjotie 30 Fin-96320 Rovaniemi...
All genuine Can-Am ATV parts and accessories, installed by an authorized BRP Distributors/Dealers at the time of delivery of the 2007 Can-Am ATV, carry the same warranty as that of the ATV. Use of the product for racing or any other competitive activity, at any point, even by a previous owner, will render this warranty null and void.
Page 135
This warranty coverage is available only if each of the following conditions has been fulfilled: • The 2007 Can-Am ATV must be purchased as new and unused by its first owner from a Can-Am Distributor/Dealer authorized to distribute Can-Am ATVs in the country in which the sale occurred;...
Page 136
BRP’s obligations under this warranty are limited to, at its sole discretion, repair- ing parts found defective under normal use, maintenance and service, or replac- ing such parts with new genuine Can-Am parts without charge for parts and labor, at any authorized BRP Distributor/Dealer during the warranty coverage period.
Page 137
For countries within Europe, Middle East, Africa, Russia & CIS, please contact our European office: BRP EUROPE N.V. Consumer Service Center SKALDENSTRAAT 125 9042 GENT Belgium Tel.: + 32-9-218-26-00 For Scandinavian countries, please contact our Finland office: BRP FINLAND OY Service Department Ahjotie 30 Fin-96320 Rovaniemi...
PRIVACY OBLIGATION/DISCLAIMER We wish to inform you that your coordinates will be used for safety and warranty purposes. Sometimes, we also use the coordinates of our clients to inform them about our products and to present them offers. Should you prefer not to receive information on our product, services and offers, please let us know by writing to the address below.
(715) 848-4957 (USA) or (819) STOLEN UNITS: If your personal ATV 566-3366 (Canada); is stolen, you should notify BRP or an authorized Can-Am dealer. We – notifying an authorized Can-Am will ask you to provide your name, dealer. address, phone number, the vehicle...
Page 141
(715) 848-4957 (USA) or (819) STOLEN UNITS: If your personal ATV 566-3366 (Canada); is stolen, you should notify BRP or an authorized Can-Am dealer. We – notifying an authorized Can-Am will ask you to provide your name, dealer. address, phone number, the vehicle...
Page 143
ATV MODEL No. VEHICLE IDENTIFICATION NUMBER (V.I.N.) ENGINE IDENTIFICATION NUMBER (E.I.N.) Owner: NAME STREET CITY STATE/PROVINCE ZIP/POSTAL CODE Purchase Date YEAR MONTH Warranty Expiry Date YEAR MONTH To be completed by the dealer at the time of the sale. DEALER IMPRINT AREA V00A2IL Please verify with your dealer to ensure your vehicle has been registered with BRP.