Can-Am 2009 Renegade 500 Operator's Manual
  1. Manuals
  2. Brands
  3. Can-Am Manuals
  4. Offroad Vehicle
  5. 2009 Renegade 500
  6. Operator's manual

Can-Am 2009 Renegade 500 Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for Can-Am 2009 Renegade 500

Summary of Contents for Can-Am 2009 Renegade 500

  • Page 2 Take time to familiarize yourself with your new vehicle. In Canada, products are distributed by Bombardier Recreational Products Inc. (BRP). In USA, products are distributed by BRP US Inc. The following trademarks are the property of Bombardier Recreational Products Inc.: Can-Am™ Renegade™ Rotax ® XP-S™ TTI™...

  • Page 3: Foreword

    FOREWORD Congratulations on your purchase of a WARNING new Can-Am™ ATV. It's backed by the Indicates a hazardous situation BRP warranty and a network of autho- which, if not avoided, could result rized Can-Am dealers ready to provide in death or serious injury.
  • Page 4 FOREWORD change specifications, designs, fea- tures, models or equipment without incurring any obligation upon itself. SAFETY This Operator's Guide and the VIDEO should remain with the vehicle when it is sold. While reading this Operator’s Guide, reminder that: WARNING Indicates a potential hazard that, if not avoided, could result in serious injury or death.

  • Page 5: Table Of Contents

    TABLE OF CONTENTS FOREWORD ................1 Know Before You Go ..
  • Page 6 TABLE OF CONTENTS CONTROLS/INSTRUMENTS/EQUIPMENTS (cont’d) 5) Parking Brake ..............62 6) Transmission Lever.
  • Page 7 MESSAGES IN MULTIFUNCTION GAUGE ........126 WARRANTY BRP LIMITED WARRANTY USA AND CANADA: 2009 CAN-AM ATV .. 128 BRP INTERNATIONAL LIMITED WARRANTY: 2009 CAN-AM ATV .
  • Page 8 TABLE OF CONTENTS _______________...

  • Page 9: Safety Information

    SAFETY INFORMATION ________ ________ SAFETY INFORMATION...

  • Page 10: General Precautions

    Since these changes have not been tested by BRP, they may increase the risk of crashes or injuries, and they can make the vehicle illegal. See your authorized Can-Am dealer for available accessories for your vehicle. ________ ________ SAFETY INFORMATION...

  • Page 11: Special Safety Messages

    – Never operate this vehicle without proper instruction. Take a training course. All operators should receive training from a certified instructor. Contact an authorized Can-Am dealer for more information. USA and Canada only: to find out about available training course near-...
  • Page 12 SPECIAL SAFETY MESSAGES WARNING – Never operate on excessively rough, slippery or loose terrain until you have learned and practiced the skills necessary to control this vehicle on such terrain. Always be especially cautious on these kinds of terrain. – Always follow proper procedures for turning as described further in this Operator's Guide.
  • Page 13 SPECIAL SAFETY MESSAGES WARNING – Always be sure there are no obstacles or people behind the vehicle when you operate in reverse. When it is safe to proceed in reverse, go slowly. – Always use the size and type tires specified further in this Operator's Guide.

  • Page 14: Operation Warnings

    Beginning and inexperienced operators should complete a training course. They should then regularly practice the skills learned in the course and the operating techniques described in this Operator's Guide. For more information about the training course, contact an authorized Can-Am dealer. _______ ________ SAFETY INFORMATION...
  • Page 15 OPERATION WARNINGS WARNING POTENTIAL HAZARD Failure to follow the age recommendations for this vehicle. WHAT CAN HAPPEN A lack of respect for this age recommendation can lead to severe injury or death of the child. Even though a child may be within the age group for which this vehicle is recommended, he may not have the skills, abilities, or judgment needed to operate this vehicle safely and may be involved in a serious accident.
  • Page 16 OPERATION WARNINGS WARNING POTENTIAL HAZARD Carrying a passenger on this vehicle. WHAT CAN HAPPEN Greatly reduces your ability to balance and control this vehicle. Could cause an accident, resulting in harm to you and/or your passenger. HOW TO AVOID THE HAZARD Never carry passenger.
  • Page 17 OPERATION WARNINGS WARNING POTENTIAL HAZARD Operating this vehicle on paved surfaces. WHAT CAN HAPPEN The tires are designed for off-road use only, not for use on pavement. Paved surfaces may seriously affect handling and control of this vehicle, and may cause the vehicle to go out of control.
  • Page 18 OPERATION WARNINGS WARNING POTENTIAL HAZARD Operating this vehicle on public streets, roads or highways. WHAT CAN HAPPEN You can collide with another vehicle. HOW TO AVOID THE HAZARD Never operate this vehicle on any public street, road or highway, even a dirt or gravel one.
  • Page 19 OPERATION WARNINGS WARNING POTENTIAL HAZARD Riding this vehicle without wearing an approved helmet, eye protection and protective clothing. WHAT CAN HAPPEN The following items concern all ATV's operator: – Riding without an approved helmet increases the chances of a severe head injury or death in the event of an accident.
  • Page 20 OPERATION WARNINGS WARNING POTENTIAL HAZARD Riding this vehicle after consuming alcohol or drugs. WHAT CAN HAPPEN Could seriously affect your judgment. Could cause you to react more slowly. Could affect your balance and perception. Could result in an accident or death. HOW TO AVOID THE HAZARD Never consume alcohol or drugs before or while riding this vehicle.
  • Page 21 OPERATION WARNINGS WARNING POTENTIAL HAZARD Operating this vehicle at excessive speeds. WHAT CAN HAPPEN Increases your chances of losing control of the vehicle, which can result in an accident. HOW TO AVOID THE HAZARD Always travel at a speed which is proper for the terrain, visibility and oper- ating conditions, and your experience.
  • Page 22 OPERATION WARNINGS WARNING POTENTIAL HAZARD Attempting wheelies, jumps and other stunts. WHAT CAN HAPPEN Increases the chance of an accident, including an overturn. HOW TO AVOID THE HAZARD Never attempt stunts, such as wheelies or jumps. Do not try to show off. WARNING POTENTIAL HAZARD Failure to inspect the vehicle before operating.
  • Page 23 OPERATION WARNINGS WARNING POTENTIAL HAZARD Riding on frozen waterways. WHAT CAN HAPPEN Breaking through the ice can lead to severe injury or death. HOW TO AVOID THE HAZARD Never ride this vehicle on a frozen surface before you are sure the ice is thick enough and sound enough to support the vehicle and its load, as well as the force that is created by a moving vehicle.
  • Page 24 OPERATION WARNINGS WARNING POTENTIAL HAZARD Failure to use extra care when operating this vehicle on unfamiliar terrain. WHAT CAN HAPPEN You can come upon hidden rocks, bumps, or holes, without enough time to react. Could result in the vehicle overturning or loss of control. HOW TO AVOID THE HAZARD Go slowly and be extra careful when operating on unfamiliar terrain.
  • Page 25 OPERATION WARNINGS WARNING POTENTIAL HAZARD Failure to use extra care when operating on excessively rough, slippery or loose terrain. WHAT CAN HAPPEN Could cause loss of traction or vehicle control, which could result in an acci- dent, including an overturn. HOW TO AVOID THE HAZARD Do not operate on excessively rough, slippery or loose terrain until you have learned and practiced the skills necessary to control this vehicle on...
  • Page 26 OPERATION WARNINGS WARNING POTENTIAL HAZARD Turning improperly. WHAT CAN HAPPEN Vehicle could go out of control, causing a collision or overturn. HOW TO AVOID THE HAZARD Always follow proper procedures for turning as described further in this Op- erator's Guide. Practice turning at low speeds before attempting to turn at faster speeds.
  • Page 27 OPERATION WARNINGS WARNING POTENTIAL HAZARD Operating on excessively steep hills. WHAT CAN HAPPEN The vehicle can overturn more easily on extremely steep hills than on level surfaces or small hills. HOW TO AVOID THE HAZARD Never operate this vehicle on hills too steep for the vehicle or for your abili- ties.
  • Page 28 OPERATION WARNINGS WARNING POTENTIAL HAZARD Climbing hills improperly. WHAT CAN HAPPEN Could cause loss of control or cause vehicle to overturn. HOW TO AVOID THE HAZARD Always follow proper procedures for climbing hills as described further in this Operator's Guide. Always check the terrain carefully before you start up any hill.
  • Page 29 OPERATION WARNINGS WARNING POTENTIAL HAZARD Going down a hill improperly. WHAT CAN HAPPEN Could cause loss of control or cause vehicle to overturn. HOW TO AVOID THE HAZARD Always follow proper procedures for going down hills as described further in this Operator's Guide. NOTE: A special technique is required when braking as you go down a hill.
  • Page 30 OPERATION WARNINGS WARNING POTENTIAL HAZARD Improperly crossing hills or turning on hills. WHAT CAN HAPPEN Could cause loss of control or cause vehicle to overturn. HOW TO AVOID THE HAZARD Never attempt to turn the vehicle around on any hill until you have mastered the turning technique as described further in this Operator's Guide on level ground.
  • Page 31 OPERATION WARNINGS WARNING POTENTIAL HAZARD Stalling, rolling backwards or improperly dismounting while climbing a hill. WHAT CAN HAPPEN Could result in vehicle overturning. HOW TO AVOID THE HAZARD Use proper gear and maintain steady speed when climbing a hill. If you lose all forward speed: Keep your weight uphill.
  • Page 32 OPERATION WARNINGS WARNING POTENTIAL HAZARD Improperly operating over obstacles. WHAT CAN HAPPEN Could cause loss of control or a collision. Could cause the vehicle to overturn. HOW TO AVOID THE HAZARD Before operating in a new area, check for obstacles. Never attempt to ride over large obstacles, such as large rocks or fallen trees.
  • Page 33 OPERATION WARNINGS WARNING POTENTIAL HAZARD Skidding or sliding improperly. WHAT CAN HAPPEN You may lose control of this vehicle. You may also regain traction unexpectedly, which may cause the vehicle to overturn. HOW TO AVOID THE HAZARD Learn to safely control skidding or sliding by practicing at low speeds and on level smooth terrain.
  • Page 34 OPERATION WARNINGS WARNING POTENTIAL HAZARD Operating this vehicle through deep or fast flowing water. WHAT CAN HAPPEN Tires may float, causing loss of traction and loss of control, which could lead to an accident. HOW TO AVOID THE HAZARD Never operate this vehicle in fast flowing water or in water deeper than that specified further in this Operator's Guide.
  • Page 35 OPERATION WARNINGS WARNING POTENTIAL HAZARD Improperly operating in reverse. WHAT CAN HAPPEN You could hit an obstacle or person behind the vehicle, resulting in serious injury. HOW TO AVOID THE HAZARD When you select reverse gear, make sure there are no obstacles or people behind the vehicle.
  • Page 36 OPERATION WARNINGS WARNING POTENTIAL HAZARD Operating this vehicle with improper tires, or with improper or uneven tire pressure. WHAT CAN HAPPEN Use of improper tires on this vehicle, or operation of this vehicle with improper or uneven tire pressure, may cause loss of control, tire blow outs, tire to move around on its rim and increases the risk of an accident.
  • Page 37 All parts and accessories added to this vehicle should be approved by BRP and should be installed and used according to instructions. If you have questions, consult an authorized Can-Am dealer. NEVER install passenger seat or use the cargo area to carry a passenger.
  • Page 38 OPERATION WARNINGS WARNING POTENTIAL HAZARD Overloading this vehicle or carrying or towing cargo improperly. WHAT CAN HAPPEN Could cause changes in vehicle handling which could lead to an accident. HOW TO AVOID THE HAZARD Never exceed the stated load capacity for this vehicle including operator, as well as other loads and added accessories.
  • Page 39 OPERATION WARNINGS WARNING POTENTIAL HAZARD Transporting flammable or dangerous material can lead to explosions. WHAT CAN HAPPEN This can cause serious injury or death. HOW TO AVOID THE HAZARD Never transport flammable or dangerous material. While reading this Operator’s Guide, reminder that: WARNING Indicates a potential hazard that, if not avoided, could result in serious injury or death.

  • Page 40: Riding The Vehicle

    Information in this Operator's Guide is limited. It is strongly recommended that you obtain further information and training from your local authorities, ATV clubs, a recognized ATV training organization or contact an authorized Can-Am dealer. USA and Canada only: to find out about available training course nearest you, call the Specialty Vehicle Institute of America (SVIA) at 1 800 887-2887 or in Canada, the Canada safety Council (CSC) at 1 613 739-1535 ext.

  • Page 41: Pre-Ride Inspection

    – Check operation of 2WD/4WD selector. NOTICE Correct any problem you may have found before riding. See an au- thorized Can-Am dealer as necessary. Clothing Actual weather conditions should help you decide how to dress. However, it is im- portant that the operator always wears the appropriate protective clothing and ap-...

  • Page 42: Carrying Loads

    RIDING THE VEHICLE shirt and pants. This type of clothing will provide you protection from some of the minor hazards you may encounter en route. The operator must never wear loose clothing such as a scarf that may get entangled in the vehicle or on tree branches and shrubs.

  • Page 43: Hauling A Trailer

    Your vehicle can help you perform a number of different LIGHT tasks ranging from snow removal to pulling wood or carrying cargo. A variety of accessories are available from your authorized Can-Am dealer. However, always respect the load and capacities of the vehicle. Overloading of the vehicle can overstress the components and cause failure.

  • Page 44: Environment

    RIDING THE VEHICLE Join a local ATV club. It will provide you with a map and advice or inform you where you can ride. If a club does not exist in your area, help to start one. Group riding and club activities provide a pleasurable, social experience.

  • Page 45: Off-Highway Operation

    RIDING THE VEHICLE Off-Highway Operation The very nature of off-highway operation is dangerous. Any terrain, which has not been specially prepared to carry vehicles, presents an inherent danger where angularity, terrain substance and exact steepness are unpredictable. The terrain itself presents a continual element of danger, which must be knowingly accepted by anyone venturing over it.

  • Page 46: Downhill Driving

    RIDING THE VEHICLE Downhill Driving This vehicle can climb steeper ropes than it can descend safely. Therefore, it is es- sential to assure that a safe route exists to descend a slope before you climb it. Decelerating while negotiating a slippery downhill slope could “toboggan” the ve- hicle.
  • Page 47 RIDING THE VEHICLE Even though there is an adequate suspensions system on this vehicle there are “washboard” or rough terrain conditions that will make you feel uncomfortable and even cause back injury. “Posting” or riding in a crouched position will often be required.
  • Page 48 RIDING THE VEHICLE Water will affect the braking ability of your vehicle. Make sure you dry the brakes by applying them several times after the vehicle leaves the water. Mud or marsh lands may be encountered near water. Be prepared for sudden “holes”...
  • Page 49 RIDING THE VEHICLE When riding in sand dunes it is advisable to equip the vehicle with an antenna type safety flag. This will help make your location more visible to others over the next sand dune. Proceed carefully should you see another safety flag ahead. Since the antenna type safety flag can snag and rebound on your body if caught, do not use it in areas where there are low hanging branches or obstacles.
  • Page 50 RIDING THE VEHICLE Uphill Keep your body weight forward towards the top of the hill. Keep your feet on the footpegs and shift into low gear then accelerate and when necessary, change gear quickly as you climb. Do not over-speed since this may cause the front of the vehi- cle to lift from the ground and fall back on you.

  • Page 51: Routine Maintenance

    RIDING THE VEHICLE Side Hilling This is one of the most risky types of riding since it may drastically change the bal- ance of the vehicle. It should be avoided wherever possible. If it is necessary to do so however, it is important that you ALWAYS keep your body weight on the upside of the slope...
  • Page 52 Part of your responsibility towards safety is to respect the contents of this Opera- tor's Guide. It provides valuable advice on how to properly take care of your vehi- cle. If further assistance is required your authorized Can-Am dealer is always will- ing to help.

  • Page 53: Hang Tag

    HANG TAG This vehicle comes with a hang tag and labels containing important safety informa- tion. Any person who rides this vehicle should read and understand this information be- fore riding. vmo2009-005-003_en USA and Canada Only vmo2006-005-009_en ________ ________ SAFETY INFORMATION...

  • Page 54: Important On-Product Labels

    The following labels are on your vehicle and they should be considered perma- nent parts of the vehicle. If missing or damaged, they can be replaced free of charge. See an authorized Can-Am dealer. NOTE: The following illustrations used in this Operator's Guide are a general representation only.
  • Page 55 IMPORTANT ON-PRODUCT LABELS vmo2007-015-005_a LABEL 3 LABEL 4 vmo2009-003-004_en LABEL 1 LABEL 5 LABEL 2 ________ ________ SAFETY INFORMATION...
  • Page 56 IMPORTANT ON-PRODUCT LABELS vmo2007-015-019_en LABEL 6 vmo2006-014-003_a LABEL 8 vmo2007-002-002 LABEL 7: LOCATED UNDER SEAT ON THE vmo2007-015-020_en UPPER BAR OF FRAME LABEL 9 LABEL 10 _______ ________ SAFETY INFORMATION...
  • Page 57 IMPORTANT ON-PRODUCT LABELS vmo2008-014-001 LABEL 11 ________ ________ SAFETY INFORMATION...
  • Page 58 IMPORTANT ON-PRODUCT LABELS _______ ________ SAFETY INFORMATION...

  • Page 59: Vehicle Information

    VEHICLE INFORMATION _______________...

  • Page 60: Controls/Instruments/Equipments

    CONTROLS/INSTRUMENTS/EQUIPMENTS NOTE: Some controls/instruments/equipment are optional. vmo2008-005-100_e TYPICAL While reading this Operator’s Guide, reminder that: WARNING Indicates a potential hazard that, if not avoided, could result in serious injury or death. ______________...
  • Page 61 CONTROLS/INSTRUMENTS/EQUIPMENTS vmo2008-005-009_b TYPICAL _______________...

  • Page 62: Throttle Lever

    CONTROLS/INSTRUMENTS/EQUIPMENTS vmo2008-005-010_c TYPICAL 1) Throttle Lever When pushed, it increases the engine speed that allows the engagement of the transmission on the selected gear. When released, the engine speed should return automatically to idle and the vehicle will gradually slow down. TYPICAL 1.

  • Page 63: 2Wd/4Wd Selector

    CONTROLS/INSTRUMENTS/EQUIPMENTS 2) 2WD/4WD Selector This selector allow to choose between 2WD or 4WD when the vehicle is stopped. TYPICAL 1. Selector 4WD MODE 2. 2WD position 3. 4WD position To deselect the 4WD mode, press the selector on 2WD. NOTICE vehicle must stopped to engage or disengage...

  • Page 64: Rear Brake Lever

    CONTROLS/INSTRUMENTS/EQUIPMENTS 3) Rear Brake Lever 5) Parking Brake When compressed, the rear brake is When applied, it prevents the vehicle applied. When released, the brake from moving. Useful when the brake lever should automatically return to needs to be locked for example when its original position.

  • Page 65: Transmission Lever

    In some circumstances, it system inspect by an authorized may be necessary to rock the vehicle Can-Am dealer as soon as possi- back and forth to move the gears in the ble. transmission to allow the park to be engaged.

  • Page 66: Multifunction Switch

    CONTROLS/INSTRUMENTS/EQUIPMENTS H: High gear Headlights Switch This selects the high speed range of the transmission in the gear box. It is the normal driving speed range. It al- lows the vehicle to reach its maximum speed. L: Low gear This selects the low speed range of the transmission in the gear box.
  • Page 67 CONTROLS/INSTRUMENTS/EQUIPMENTS Engine Stop Switch This switch can be used to stop the en- gine and as an emergency control. To stop engine, fully release throttle lever then use the engine stop switch. NOTE: While engine can be stopped by turning ignition key to OFF position, we recommend the engine be stopped by the engine stop switch.

  • Page 68: Multifunction Gauge

    8) Multifunction Gauge meter are factory preset in miles but it is possible to change them to kilo- meter reading. Contact an authorized WARNING Can-Am dealer. Never adjust or set functions on the multifunction gauge while rid- Multifunction Display ing the vehicle.
  • Page 69 CONTROLS/INSTRUMENTS/EQUIPMENTS RPM Mode In this mode, the display shows the en- gine RPM. vdd2008-001-083 5. To select another mode, repeat steps 3 and 4 until you get the mode desired. vdd2008-001-089 Multifunction Display (temporary display mode) Combined Mode Press and release selector button to In this mode, the display shows the change the normal display mode to the speed of the vehicle and the engine...
  • Page 70 Hour Meter (trip time) nication error. Contact an authorized The hour meter records vehicle run- Can-Am dealer. ning time when the electrical system is activated. It can be used to establish Fuel Level Display...

  • Page 71: 12-Volt Power Outlet

    When this indicator is ON, it in- the front of vehicle underneath dash dicates the 4WD system is acti- board. See an authorized Can-Am deal- vated. er for more details. When this indicator is ON, it in-...

  • Page 72: Rear Brake Pedal

    However, the DESS brings a great flexi- bility. You can buy an additional ignition key and have it programmed for your vehicle. To have additional ignition key, refer to an authorized Can-Am dealer. vmo2007-015-010_a 11) Rear Brake Pedal 1. Rear storage compartment cover 2. Latch When pressed down, the rear brake is applied.

  • Page 73: Seat Latch

    CONTROLS/INSTRUMENTS/EQUIPMENTS 13) Seat Latch It allows the removal of seat to give ac- cess to engine compartment. vmo2008-005-003_a 1. Insert these tabs in hooks 2. Hooks 1. Seat latch WARNING Seat Removal Push latch forward while gently lifting Make sure seat is securely latched rear of seat.

  • Page 74: Recovery Hook

    CONTROLS/INSTRUMENTS/EQUIPMENTS WARNING MAXIMUM load for cargo area is 16 kg (35 lb). Ensure to properly secure articles to rear fender. Do not overload. Ensure load does not interfere with visibility. Do not carry passenger(s). SPECIFICATIONS Refer to for carry- ing loads and cargo weight distribution recommendations.

  • Page 75: Fuel

    FUEL Recommended Fuel WARNING Use regular unleaded gasoline, avail- Always stop engine before refu- able from most service stations or oxy- eling. Open cap slowly. If a dif- genated fuel containing a maximum ferential pressure condition is no- total of 10% of ethanol or methanol ticed (whistling sound heard when or both.

  • Page 76: Operating Instructions

    300 km (185 mi) of riding, your ve- is fully disengaged before operating hicle be inspected by an authorized the vehicle. MAINTE- Can-Am dealer. Refer to NANCE section. Gradually press the throttle lever to increase engine speed and thus en-...

  • Page 77: Stopping The Engine

    Should the vehicle become immersed, Remove key from ignition switch. it will be necessary to take it to an au- thorized Can-Am dealer as soon as pos- Post-Operation Care sible. NEVER START THE ENGINE! When vehicle is used in salt-water...

  • Page 78: Tune Your Ride

    TUNE YOUR RIDE Renegade 800 X WARNING Suspension adjustment could af- fect vehicle handling. Always take time to familiarize yourself with the vehicle's behavior after any suspension adjustment have been made. Suspension Adjustment Your vehicle handling and comfort de- pend upon suspension adjustments. vmo2008-021-003_a TYPICAL Choice of suspension adjustments...
  • Page 79 TUNE YOUR RIDE vmo2008-021-001_a vmo2008-021-004_a TYPICAL — FRONT PRELOAD ADJUSTMENT TYPICAL A. Same length 1. Compression adjuster (flat screwdriver) Turning it clockwise (H) increases shock damping action (stiffer). Turning it counterclockwise (S) de- creases shock damping action (softer). Compression (High Speed) Use a 17 mm wrench to adjust it.
  • Page 80 TUNE YOUR RIDE vmo2008-021-005_a 1. Rebound adjuster Turning it clockwise (H) increases shock damping action (stiffer). Turning it counterclockwise (S) de- creases shock damping action (softer). While reading this Operator’s Guide, reminder that: WARNING Indicates a potential hazard that, if not avoided, could result in serious injury or death.

  • Page 81: Vehicle Transportation

    VEHICLE TRANSPORTATION When transporting a vehicle, secure vehicle to trailer or in pickup box with suitable tie-downs. Using ordinary ropes is not recommended. WARNING Never tip this vehicle on end for transporting. We recommend that you carry the vehicle in its nor- mal operating position (on all four vmo2008-005-004_a wheels).
  • Page 82 VEHICLE TRANSPORTATION ______________...

  • Page 83: Maintenance Information

    MAINTENANCE INFORMATION _______________...

  • Page 84: Maintenance Schedule

    If not, see your authorized Can-Am dealer. Other important items in the maintenance schedule that are more difficult and re- quire special tools are best performed by your authorized Can-Am dealer. WARNING Turn off the engine and follow these maintenance procedures when per- forming maintenance.
  • Page 85 MAINTENANCE SCHEDULE PERIODIC MAINTENANCE CHART INITIAL INSPECTION 10 H OR 30 DAYS OR 300 km (185 mi) (To be performed by an authorized Can-Am dealer. The initial maintenance is very important and must not be neglected.) A: ADJUST C: CLEAN...
  • Page 86 MAINTENANCE SCHEDULE PERIODIC MAINTENANCE CHART INITIAL INSPECTION 10 H OR 30 DAYS OR 300 km (185 mi) (To be performed by an authorized Can-Am dealer. The initial maintenance is very important and must not be neglected.) A: ADJUST C: CLEAN...
  • Page 87 MAINTENANCE SCHEDULE PERIODIC MAINTENANCE CHART INITIAL INSPECTION 10 H OR 30 DAYS OR 300 km (185 mi) (To be performed by an authorized Can-Am dealer. The initial maintenance is very important and must not be neglected.) A: ADJUST C: CLEAN...
  • Page 88 MAINTENANCE SCHEDULE PERIODIC MAINTENANCE CHART INITIAL INSPECTION 10 H OR 30 DAYS OR 300 km (185 mi) (To be performed by an authorized Can-Am dealer. The initial maintenance is very important and must not be neglected.) A: ADJUST C: CLEAN...
  • Page 89 MAINTENANCE SCHEDULE PERIODIC MAINTENANCE CHART INITIAL INSPECTION 10 H OR 30 DAYS OR 300 km (185 mi) (To be performed by an authorized Can-Am dealer. The initial maintenance is very important and must not be neglected.) A: ADJUST C: CLEAN...

  • Page 90: 10-Hour Inspection

    As with any precision piece of mechanical equipment, we suggest that after the first 10 hours or 300 km (185 mi) of operation, whichever comes first, your vehicle be inspected by an authorized Can-Am dealer. This inspection will give you the opportunity to discuss the unanswered questions you may have encountered during the first hours of operation.

  • Page 91: Maintenance Procedures

    MAINTENANCE PROCEDURES Air Filter Air Filter Removal NOTICE Never remove or mod- ify any component in the air filter housing. Otherwise, engine perfor- mance degradation or damage can occur. The engine is calibrated to operate specifically with these com- ponents. vmo2006-007-028_a Remove seat and central panel.

  • Page 92: Engine Oil

    MAINTENANCE PROCEDURES Remove foam prefilter by carefully Air Filter Installation pushing the extremities toward the in- Properly reinstall removed parts in the side. reverse order of their removal. Engine Oil Engine Oil Level NOTICE Check level frequently and refill if necessary. Do not over- fill.
  • Page 93 MAINTENANCE PROCEDURES NOTE: For improved overall perfor- mance and all season applications, use XP-S 5W 40 synthetic oil (P/N 293 600 039). Engine Oil Viscosity Chart XP-S 5W 40 Synthetic Oil (P/N 293 600 039) SAE 0W 30 SAE 5W 30 SAE 10W 30 XP-S 10W 40 Mineral Oil (P/N 219 700 346)

  • Page 94: Radiator

    MAINTENANCE PROCEDURES Ensure vehicle is on a level surface. Check the cover O-ring and change it if necessary. Remove dipstick. Screw oil filter cover in place. Clean the oil drain plug area. Wipe off any oil spillage on engine. Place a drain pan under the oil drain plug area.

  • Page 95: Engine Coolant

    PRESSURE ONLY, NEVER USE A If the coolant is added in the coolant HIGH PRESSURE WASHER. reservoir, check the level in the radia- See an authorized Can-Am dealer to tor too. Add coolant if necessary. check the performance of the cooling system.
  • Page 96 MAINTENANCE PROCEDURES Cooling system must be filled with BRP premixed coolant (P/N 219 700 362) or with distilled water and an- tifreeze solution (50% distilled water, 50% antifreeze). Engine Coolant Replacement WARNING In order to avoid potential burns, vmo2006-007-021_a do not remove the radiator cap or 1.

  • Page 97: Spark Arrester

    MAINTENANCE PROCEDURES WARNING Never run engine in an enclosed area. Never perform this opera- tion immediately after the engine has been run because exhaust sys- tem is very hot. Make sure that there are no combustible mate- rials in the area. Wear eye pro- tection and gloves.

  • Page 98: Cvt Air Filter

    MAINTENANCE PROCEDURES CVT Air Filter 800R EFI Only CVT Air Filter Removal 1. Remove seat and central panel. BODY Refer to section. 2. Locate access cover on LH side of vehicle underneath front fender. 3. Remove plastic darts that hold ac- cess cover.
  • Page 99 MAINTENANCE PROCEDURES vmo2009-008-035 CLAMP PRE-INSTALLATION vmo2009-008-037_a 3. Insert foam with clamp on CVT air CVT AIR INLET REMOVED FOR CLARITY PURPOSE inlet as per the following illustra- 1. Filter elastic tion. 2. Clamp 4. Ensure that the clamp is properly The following illustration shows the fi- positioned on the air inlet edge and nal assembly.

  • Page 100: Cvt Cover Drain Screw

    MAINTENANCE PROCEDURES CVT Cover Drain Screw Any time you suspect that water has entered the CVT cover, drain the CVT housing by removing the drain screw. vmo2006-007-018_a 1. Oil level plug 2. Oil drain plug The oil should be level with the bottom of the oil level hole.

  • Page 101: Throttle Cable

    MAINTENANCE PROCEDURES The oil should be level with the bottom of the oil level hole. Refill as required until gearbox oil level flows through oil level hole. Reinstall oil level plug. Throttle Cable Throttle Cable Lubrication The throttle cable must be lubricated with silicone lubricant (P/N 293 600 041) or an equivalent.

  • Page 102: Throttle Lever

    MAINTENANCE PROCEDURES TYPICAL NOTE: Place a rag around the throttle Remove the throttle body side cover. cable adjuster to prevent the lubricant from splashing. Add lubricant until it runs out at throttle body end of the throttle cable. Reinstall and adjust the cable. Throttle Lever Throttle Lever Adjustment Slide rubber protector back to expose...

  • Page 103: Spark Plug

    MAINTENANCE PROCEDURES Unscrew spark plugs completely then remove them. TYPICAL 1. Throttle lever vmo2006-007-029_a A. 3 to 6 mm (1/8 to 7/32 in) RH SIDE — REAR CYLINDER 1. Spark plug With the transmission lever on PARK position, start the engine. Check if the throttle cable is adjusted correctly by turning handlebar fully right then ful- ly left.

  • Page 104: Battery

    MAINTENANCE PROCEDURES Torque spark plugs to 20 N•m (15 lbf•ft). Battery WARNING Unless otherwise indicated, al- ways turn ignition switch to the OFF position before performing any maintenance or repair on elec- trical system. vmr2007-047-001_a WARNING Pull out top bracket. Never charge a battery while in- stalled in vehicle.
  • Page 105 MAINTENANCE PROCEDURES If a fuse is damaged, replace it by one of the same rating. NOTICE Do not use a higher rated fuse as this can cause severe dam- age. Fuse Inspection To remove fuse from holder, remove the fuse holder cover then pull fuse out.

  • Page 106: Lights

    MAINTENANCE PROCEDURES Lights WARNING Always turn the ignition switch to OFF position before replacing a de- fective bulb. Always check light operation after re- placement. Headlight Bulb Replacement vmr2007-050-007_a NOTICE Never touch glass portion Pull out bulb. of a halogen bulb with bare fingers, it shortens its operating life.

  • Page 107: Drive Shaft Boot/Protector

    Push and pull the wheels from the up- per edge to feel the play. See an autho- Visually inspect drive shaft protectors rized Can-Am dealer if there is any play. and boots conditions. Check protec- tors for damage or rubbing against...
  • Page 108 MAINTENANCE PROCEDURES vmo2007-015-014_a TIGHTENING SEQUENCE NOTICE Always use the recom- mended wheel nuts (P/N 250 100 082). Using a different nut could cause damages to the rim. Tire Pressure TYPICAL WARNING Wheel Removal/Installation Tire pressure greatly affects vehi- Loosen nuts then lift vehicle. Place a cle handling and stability.

  • Page 109: Suspension

    Check trailing arms for distortion, WARNING cracks or bending. See an authorized When the tires are replaced, nev- Can-Am dealer if any problem is de- er install a bias tire with a radial tected. tire. Such a combination could create handling and/or stability Brake problems.
  • Page 110 MIN. and thickness MAX. level marks. Maximum discs 0.3 mm (.010 in) warpage See your authorized Can-Am dealer if a problem is detected concerning the brake system. WARNING The brake fluid replacement or brake system maintenance and...

  • Page 111: Body

    Seat Fasteners Remove seat and check latch mecha- vmo2008-005-002_a nism and pin for wear. See an autho- 1. Lift here rized Can-Am dealer for parts replace- Come off the plastic studs from the ment if damaged. grommets. Vehicle Cleaning and Protection Never use a high pressure washer to clean the vehicle.

  • Page 112: Frame

    MAINTENANCE PROCEDURES Frame Recovery Hook Condition Check tightness of fasteners. Properly retighten as necessary. Frame Fasteners Check fastener condition and tight- ness on the vehicle. Retighten as re- quired. While reading this Operator’s Guide, reminder that: WARNING Indicates a potential hazard that, if not avoided, could result in serious injury or death.

  • Page 113: Storage And Preseason Preparation

    CHART When a vehicle is not in use for more than 4 months, proper storage is a ne- cessity. See an authorized Can-Am dealer for proper procedures. When using your vehicle after stor- age, a preparation is required. See an authorized Can-Am dealer for proper procedures.
  • Page 114 STORAGE AND PRESEASON PREPARATION ______________...

  • Page 115: Technical Information

    TECHNICAL INFORMATION ______________...

  • Page 116: Vehicle Identification

    These numbers are required by the authorized Can-Am dealer to com- plete warranty claims properly. No warranty will be allowed by BRP Inc. if the engine identification number (EIN) or vehicle identification number (VIN) is removed or mutilated in any way.

  • Page 117: Noise Emission Control System Regulation

    NOISE EMISSION CONTROL SYSTEM REGULATION USA and Canada Only Tampering with Noise Control Sys- tem Is Prohibited! U.S. Federal law and Canadian provin- cial laws may prohibit the following acts or the causing there of: 1. The removal or rendering inoper- ative by any person other than for purposes of maintenance, repair or replacement of any device or ele-...

  • Page 118: Specifications

    SPECIFICATIONS MODEL RENEGADE 500 RENEGADE 800/800 X ENGINE 4-stroke, Single Over Head Camshaft (SOHC), Engine type liquid cooled Number of cylinders Number of valves 8 valves (mechanical adjustment) Bore mm (in) 82 (3.23) 91 (3.58) Stroke mm (in) 47 (1.85) 61.5 (2.42) Displacement 500 cm³...
  • Page 119 SPECIFICATIONS MODEL RENEGADE 500 RENEGADE 800/800 X ELECTRICAL SYSTEM (cont'd) Type Dry battery type Voltage 12 volts Battery Nominal rating 18 A•h Power starter output 0.7 KW headlights 4 x 60 taillight 8/26 Director indicator (European models only) Accessories 20 A 20 A Main 30 A...
  • Page 120 SPECIFICATIONS MODEL RENEGADE 500 RENEGADE 800/800 X CVT TRANSMISSION Type CVT (Continuously Variable Transmission) Engagement RPM ± 100 RPM 1600 GEARBOX Type Dual range (HI-LO) with park, neutral and reverse Capacity 400 ml (14 U.S. oz) Gearbox oil Recommended XP-S chaincase oil (P/N 413 801 900) DRIVE SYSTEM Front 500 ml (17 U.S.
  • Page 121 SPECIFICATIONS MODEL RENEGADE 500 RENEGADE 800/800 X SUSPENSION (cont'd) REAR Suspension type TTI™ independent Suspension travel mm (in) 229 (9) Shock absorber Type 5 settings X: HPG Clicker BRAKES Front brake Type Hydraulic, 2 discs Rear brake Type Hydraulic, single disc Capacity 125 ml (4.3 U.S.
  • Page 122 SPECIFICATIONS MODEL RENEGADE 500 RENEGADE 800/800 X TIRES AND WHEELS (cont’d) WHEELS Front 12 x 6 Size Rear 12 x 7.5 Wheel nuts torque 100 N•m (74 lbf•ft) WEIGHT AND DIMENSION Overall length m (in) 2.18 (86) Overall width m (in) 1.17 (46) Overall height m (in)

  • Page 123: Troubleshooting

    TROUBLESHOOTING ______________...

  • Page 124: Technical Guidelines

    • Install new spark plugs if possible or clean and dry spark plugs. • Start engine as explained above. If engine continues to flood, see an authorized Can-Am dealer. NOTE: Make sure to verify that there is no fuel in engine oil, if so, replace engine oil.
  • Page 125 – Contact an authorized Can-Am dealer. 6. Engine is under a protection mode. – Check multifunction gauge display for messages. – Multifunction gauge CHECK ENGINE indicator lamp is on and display shows CHECK ENGINE or LIMP HOME, contact an authorized Can-Am dealer. ______________...
  • Page 126 – Ensure cooling fan is not jammed and working properly. – Check fan fuse. See FUSES section. – See an authorized Can-Am dealer as soon as possible. 3. Dirty radiators fins. – Check and clean radiator fins. See MAINTENANCE PROCEDURES section.
  • Page 127 – Check multifunction gauge display for messages. – Multifunction gauge CHECK ENGINE indicator lamp is on and display shows CHECK ENGINE or LIMP HOME, contact an authorized Can-Am dealer. TRANSMISSION LEVER IS HARD TO MOVE 1. Transmission gears are in a position that prevents the transmission lever to work.

  • Page 128: Messages In Multifunction Gauge

    Can-Am dealer. Do not use the vehicle until repaired. NOTICE If the light does not turn off right after engine starting, stop en- gine. See an authorized Can-Am dealer. Do not use the vehicle until repaired. Message must be erased by an authorized Can-Am dealer. ______________...

  • Page 129: Warranty

    WARRANTY ______________...

  • Page 130: Brp Limited Warranty Usa And Canada: 2009 Can-Am

    All genuine Can-Am ATV parts and accessories, installed by an authorized BRP dealer at the time of delivery of the 2009 Can-Am ATV, carry the same warranty as that of the Can-Am ATV. This limited warranty will become null and void if: (i) the ATV was used for racing or any other competitive activity, at any point, even by a previous owner;...
  • Page 131 SIX (6) CONSECUTIVE MONTHS, for private use or commercial use owners. The emission-related components included in the chart below that are installed on EPA certified Can-Am ATVs registered in the USA are covered for thirty (30) consecutive months. EMISSION-RELATED COMPONENTS...
  • Page 132 This warranty coverage is available only if each of the following conditions has been fulfilled: – The 2009 Can-Am ATV must be purchased as new and unused by its first owner from a BRP dealer authorized to distribute Can-Am ATVs in the country in which the sale occurred ("BRP dealer");...
  • Page 133 A GPS receiver may be supplied by BRP as standard equipment on certain 2009 Can-Am ATV's. The GPS receiver is covered by the limited warranty issued by the GPS receiver’s manufacturer and is not covered by this limited warranty. Please...
  • Page 134 BRP LIMITED WARRANTY USA AND CANADA: 2009 CAN-AM 10) CONSUMER ASSISTANCE In the event of a controversy or a dispute in connection with this limited warranty, BRP suggests that you try to resolve the issue at the dealership level. We recom- mend discussing the issue with the authorized dealer's service manager or owner.

  • Page 135: Brp International Limited Warranty: 2009 Can-Am

    YOU SPECIFIC RIGHTS, AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS WHICH MAY VARY FROM COUNTRY TO COUNTRY. Neither the distributor, any Can-Am dealer nor any other person has been autho- rised to make any affirmation, representation or warranty regarding the product, other than those contained in this limited warranty, and if made, shall not be enforceable against BRP.
  • Page 136 This warranty coverage is available only if each of the following conditions has been fulfilled: – The 2009 Can-Am ATV must be purchased as new and unused by its first own- er from a Can-Am distributor/dealer authorized to distribute Can-Am ATVs in the country in which the sale occurred (“Can-Am distributor/dealer”);...
  • Page 137 BRP’s obligations under this warranty are limited to, at its sole discretion, repairing parts found defective under normal use, maintenance and service; or replacing such parts with new genuine Can-Am ATV parts without charge for parts and labour, at any authorized Can-Am distributor/dealer during the warranty coverage period under the conditions described herein.
  • Page 138 BRP INTERNATIONAL LIMITED WARRANTY: 2009 CAN-AM 2. If further assistance is required, the distributor's service department should be contacted in order to resolve the matter. 3. If the matter still remains unresolved then contact BRP by writing to us at the address listed below.

  • Page 139: Tm Atv

    All genuine Can-Am ATV parts and accessories, installed by an authorized BRP Dis- tributors/Dealers at the time of delivery of the 2009 Can-Am ATV, carry the same warranty as that of the ATV.
  • Page 140 This warranty coverage is available only if each of the following conditions has been fulfilled: – The 2009 Can-Am ATV must be purchased as new and unused by its first owner from a Can-Am Distributor/Dealer authorized to distribute Can-Am ATVs in the country in which the sale occurred;...
  • Page 141 BRP’s obligations under this warranty are limited to, at its sole discretion, repairing parts found defective under normal use, maintenance and service, or replacing such parts with new genuine Can-Am parts without charge for parts and labor, at any authorized BRP Distributor/Dealer during the warranty coverage period under the conditions described herein.
  • Page 142 BRP LIMITED WARRANTY FOR THE EUROPEAN ECONOMIC AREA: 2009 CAN-AM 9) CONSUMER ASSISTANCE In the event of a controversy or a dispute in connection with this limited warranty, BRP suggests that you try to resolve the issue at the dealership level. We rec- ommend discussing the issue with the authorized Distributor/Dealer's service manager or owner.

  • Page 143: Privacy Obligation/Disclaimer

    PRIVACY OBLIGATION/DISCLAIMER We wish to inform you that your coordinates will be used for safety and warranty purposes. Sometimes, we also use the coordinates of our clients to inform them about our products and to present them offers. Should you prefer not to receive in- formation on our product, services and offers, please let us know by writing to the address below.

  • Page 144: Change Of Address/Ownership

    STOLEN UNITS: If your personal ATV is stolen, you should notify BRP or an autho- rized Can-Am dealer. We will ask you to provide your name, address, phone num- ber, the vehicle identification number and the date it was stolen.
  • Page 145 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 146 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 147 Please verify with your dealer to ensure your vehicle has been registered with BRP. While reading this Operator’s Guide, reminder that: WARNING Indicates a potential hazard that, if not avoided, could result in serious injury or death.

This manual is also suitable for:

2009 renegade 8002009 renegade 800x

Table of Contents