Do you have a question about the DDX7019 and is the answer not in the manual?
Questions and answers
Nathan Sims
March 24, 2025
how do I reset the password from resetting the dnx7100
1 comments:
Mr. Anderson
March 24, 2025
To reset the password on a Kenwood DDX7019, try pressing the reset button. This will return the unit to factory settings. If this does not work, you may need to contact Kenwood for further assistance.
DDX7019/7029/7029Y/7039/8019/8029/8029Y/8039 DNX7100/710EX/7200 BLOCK DIAGRAM UNIT (X35- ) TOUCH FLASH TOUCH CONTROL IC304 TIMING CONTROLLER r REMOTE CONTROL INVERTER CIRCUIT RECEIVER (X14- ) RGB SW IC201 SYSTEM MONITOR OUT CHROMA COMPOSITE SW u-COM RGB SW DVD MECHA DVS-8500 MAIN AUDIO SW...
DDX7019/7029/7029Y/7039/8019/8029/8029Y/8039 DNX7100/710EX/7200 BLOCK DIAGRAM X15-101 (X15-101) to X35 from TC SCL T P+3.3V SYSTEM TC SDA SYSTEM u-COM u-COM BU3.3V SW14V XDATA SW5V LED+9V YDATA SW3.3V OPEN CLOSE KEY3 ENABLE IC605 REMO INV SW DSI/SI P ON BU3.3V SYNCHRO RESET...
Page 4
DDX7019/7029/7029Y/7039/8019/8029/8029Y/8039 DNX7100/710EX/7200 BLOCK DIAGRAM X88-202 (X88-202) IC106 IC202,203 AD [25:0] CN327 SDRAM DA [31:0] 60PIN 256Mbit CONNECTOR SDCS0 HGPIO7 IC201, FGPIO7 FGPIO5 IC211 BUS-TRA MINI LCD I/F (NOT USED) ROW7 NOR FLASH 128Mbit ROW6 SCLK1 SSPTX1 EGPIO13 ROW5 COL [7:0] (GPIO D)
DDX7019/7029/7029Y/7039/8019/8029/8029Y/8039 DNX7100/710EX/7200 COMPONENTS DESCRIPTION ● VIDEO CONTROL UNIT (X15-101x-xx/112x-xx) Ref. No. Application / Function Operation / Condition / Compatibility 3.3V regulator BU_3.3V IC10 OP AMP AREF power supply (4V) IC101 DC-DC control IC DC-DC control (Mechanism 8V, V5V) IC102 DC-DC control IC DC-DC control (SW3.3V, D5V)
DDX7019/7029/7029Y/7039/8019/8029/8029Y/8039 DNX7100/710EX/7200 ADJUSTMENT 1. Flicker adjustment 2. Automatic adjustment of RGB amplitude ● Condition (same conditon as it is used in the and WB VCOM amplitude previous models) ● Adjustment requirement Video Source: VIDEO Input signal: Input white 100% (NTSC) in VIDEO1 Video: Luster white 30%~50% ●...
DDX7019/7029/7029Y/7039/8019/8029/8029Y/8039 DNX7100/710EX/7200 ADJUSTMENT 3. TINT/PHASE adjustment 4. Adjustment of Horizontal display start ● Adjustment requirement. The adjustment is position and Pixel required to the model for PAL regions (other • GRAPHIC Adjustment screen than K and R) Screen Position Adjustment key Proceed to the next Input signal:Input magenta (PAL) in VIDEO1.
Page 10
DDX7019/7029/7029Y/7039/8019/8029/8029Y/8039 DNX7100/710EX/7200 ADJUSTMENT ● Adjustment procedure • NAVI Adjustment screen q Press HPOSI on the Test Mode Main screen. w Adjust the horizontal display start position for 2 types of the display; Graphic and NAVI. Procedure to display NAVI adjustment screen q Start the set.
Page 11
DDX7019/7029/7029Y/7039/8019/8029/8029Y/8039 DNX7100/710EX/7200 ADJUSTMENT Enlarge NG Adjustment of screen position: DNX_NAVI Left side • Pixel Adjustment: GRAPHIC 1st White dot can be seen on the left side 2nd White dot can be seen Move an arrow symbol to on the left side...
Page 12
DDX7019/7029/7029Y/7039/8019/8029/8029Y/8039 DNX7100/710EX/7200 ADJUSTMENT w-2-3 DDX_NAVI Enlarge OK Enlarge NG KNA-G520 1. Set to “1” (defult “0”). 2. Adjust the screen adjustment key so that the NAVI screen becomes horizontally symmetrical. Adjustment of pixel:DNX_NAVI Adjust the space to horizontal symmetry Enlarge OK...
DDX7019/7029/7029Y/7039/8019/8029/8029Y/8039 DNX7100/710EX/7200 ADJUSTMENT e After adjustment is completed at 4 corners and if “Write 5. Touch panel adjustment OK” is displayed, the adjustment is completed. ● Adjustment procedure Press Return to exit from the Touch Adjustment screen. q Press the Touch key on the Test Mode Menu screen to enter the Touch Panel Adjustment screen.
DDX7019/7029/7029Y/7039/8019/8029/8029Y/8039 DNX7100/710EX/7200 PC BOARD (COMPONENT SIDE VIEW) VIDEO CONTROL UNIT X15-101x-xx/112x-xx A/2 (J76-0465-02) D D D D P101 Q502 Q505 P103 C168 R550 R231 IC205 C178 R250 R553 R452 R438 R248 R137 L104 Q401 R426 R449 R136 R228 C422 L103...
DDX7019/7029/7029Y/7039/8019/8029/8029Y/8039 DNX7100/710EX/7200 EXPLODED VIEW (PANEL) ONLY ILLUSTRATION IS RC-DV340 SIZE AAA BATTERY (NOT SUPPLIED) M2x3 N09-6232-05 N09-6492-05 WASHER (1.2x3.2) N19-2332-04 M2x3 N35-2003-48 (X35-)(B/2) (X35-)(A/2) LCD1 (X89) FPC2 Depends on the models. Refer to the parts list. Parts with the exploded numbers larger than 700 are not supplied.
Page 39
DDX7019/7029/7029Y/7039/8019/8029/8029Y/8039 DNX7100/710EX/7200 EXPLODED VIEW (DRIVE MECHANISM) M2x2.5 N09-6361-05 M1.7x3.7 N09-6363-05 M2x2.5 N09-6375-05 M2x3.5 N09-6376-05 M2x2.5 N09-6377-05 φ2x2 N09-6378-05 M2.6x4 N09-6379-05 WASHER N19-2321-04 Parts with the exploded numbers larger than 700 are not supplied.
CHIP C 0.010UF K CE32BF1E101M CHIP EL 100UF 25WV C165 C93-1367-05 CHIP C 10UF K: DDX7019 K1: DDX8019 K3: DNX7100 K4: DNX710EX (North America) Indicates safety critical com po nents. E1: DDX7029 E2: DDX7029Y E3: DDX8029 E4: DDX8029Y E5: DNX7200...
Page 43
CHIP C 0.010UF K C335 CK73GB1H103K CHIP C 0.010UF K C620 CK73GB1H153K CHIP C 0.015UF K K: DDX7019 K1: DDX8019 K3: DNX7100 K4: DNX710EX (North America) Indicates safety critical com po nents. E1: DDX7029 E2: DDX7029Y E3: DDX8029 E4: DDX8029Y...
Page 44
R81-84 RK73GB2A000J CHIP R J 1/10W RK73GB2A473J CHIP R J 1/10W RK73GB2A000J CHIP R J 1/10W K: DDX7019 K1: DDX8019 K3: DNX7100 K4: DNX710EX (North America) Indicates safety critical com po nents. E1: DDX7029 E2: DDX7029Y E3: DDX8029 E4: DDX8029Y...
Page 45
R212 RK73GB2A332J CHIP R 3.3K J 1/10W R313 RK73GB2A105J CHIP R 1.0M J 1/10W K: DDX7019 K1: DDX8019 K3: DNX7100 K4: DNX710EX (North America) Indicates safety critical com po nents. E1: DDX7029 E2: DDX7029Y E3: DDX8029 E4: DDX8029Y E5: DNX7200...
Page 46
J 1/10W K3K4E5 R443 RK73GB2A102J CHIP R 1.0K J 1/10W R642 RK73GB2A000J CHIP R J 1/10W K: DDX7019 K1: DDX8019 K3: DNX7100 K4: DNX710EX (North America) Indicates safety critical com po nents. E1: DDX7029 E2: DDX7029Y E3: DDX8029 E4: DDX8029Y...
Page 47
ANALOGUE IC Q203 DTA114EUA DIGITAL TRANSISTOR IC405 BA7649F ANALOGUE IC Q204 DTC114YUA DIGITAL TRANSISTOR K: DDX7019 K1: DDX8019 K3: DNX7100 K4: DNX710EX (North America) Indicates safety critical com po nents. E1: DDX7029 E2: DDX7029Y E3: DDX8029 E4: DDX8029Y E5: DNX7200...
Page 48
CK73GB1H104K CHIP C 0.10UF C123 CC73GCH1H102J CHIP C 1000PF CN600 E41-2613-05 FLAT CABLE CONNECTOR K: DDX7019 K1: DDX8019 K3: DNX7100 K4: DNX710EX (North America) Indicates safety critical com po nents. E1: DDX7029 E2: DDX7029Y E3: DDX8029 E4: DDX8029Y E5: DNX7200...
Need help?
Do you have a question about the DDX7019 and is the answer not in the manual?
Questions and answers
how do I reset the password from resetting the dnx7100
To reset the password on a Kenwood DDX7019, try pressing the reset button. This will return the unit to factory settings. If this does not work, you may need to contact Kenwood for further assistance.
This answer is automatically generated