Page 1
Remote Blower For use with models: EHR30, EHR36, EHR42, EHR48, EHR54 ® Approved for use with All dAcor rAnges And cooktops. tested in AccordAnce with the lAtest edition of Ansi/ul 507 stAndArd for electric fAns And cAn/csA-c22.2 no. 113 stAndArd for fAns And ventilAtors.
Hazards or unsafe practices that could result in severe • Always contact the Dacor Customer Service Team personal injury or death. about problems and conditions that you don’t under- stand. cAution Hazards or unsafe practices that could result in minor personal injury or property damage.
The customer should not install, repair or replace any part of the range hood unless specifically recommended in the literature accompanying it. A qualified service technician should perform all other service. Contact the nearest Dacor authorized service representative at (800) 793-0093, or at www.Dacor.com for examination, repair or adjust- ment.
Product Specifications Dimensions Tolerances: +1/16”, -0 (1.6 mm, -0), unless otherwise stated. note: The exhaust duct(s) and electrical wiring can be connected from either the top or the back of the hood. Single exhaust models** Dual exhaust models* Standard 8” duct connection Standard 8”...
Models • Do not ground the appliance or appliance wiring to a EHR3012, EHR3018 30” (76.2 cm) gas pipeline or to the neutral (white) power supply wire. EHR3612, EHR3618 36” (91.5 cm) •...
Page 9
• The ventilation system consists of hood and a single Blower remote or single in-line blower. • A Dacor remote or in-line blower must be installed for Conduit the hood to operate properly. Only one blower shall be installed. Remote •...
Planning the Installation Duct Work Equivalent Lengths • Keep turns as far away from the hood exhaust as pos- sible, and as much space between bends as possible. eQuivAlent lengths • For best performance, use round duct instead of rect- angular, especially when elbows are required.
Preparing for Installation Electrical Service Installation Back wall wArning The electric service to the range hood should be installed only by a licensed electrician. Install a junction box in the vicinity of the hood electri- cal access holes according to local codes. Install it either behind or above the hood.
On dual exhaust models, the two 8” exhausts may be collar(s) must be moved to the rear before hanging the merged into one 10” duct using Dacor transition kit AHT10. hood. Install the transition before installing the hood on the wall. It connects to the hood on the top or rear, depending on the Place the hood assembly on a large flat surface.
The distance from the center line depends on the model. See the chart below. teMporArY BrAcket center line distAnce Models EHR3012, EHR3018 12 3/8” (31.4 cm) EHR3612, EHR3618 15 3/8” (39.1 cm) EHR4212, EHR4218 18 3/8”...
Installation Instructions Hanging the Range Hood Reattach the hood to the temporary mounting brackets. Lift the hood into its final position and fasten it in place. Insert the fasteners through the mounting slots in the wArning back and top of the hood into the studs, mounting blocks or anchors.
Page 15
Installation Instructions Connect the wiring to the remote/in-line blower and the power supply line from the junction box as shown. Neutral To remote/ (Red) in-line blower Ground (Blue) (Black) Neutral (White) To junction Ground (Green) (Green) Hood Power Terminals Connect the hood wiring to an electrical junction box on a dedicated circuit.
Page 16
Installation Instructions To house circuit breaker Separate No. 10 (minimum) panel or fuse box copper ground wire Wire Nut, Meter 3 places WHITE Fasten clamp tightly WHITE on pipe No. 4 copper GREEN wire BLACK GREEN BLACK Clamps Junction Box Bare metal UL/CSA approved insulated pipe Jumper...
• Repeat the above test. • If the hood still does not work, contact Dacor Distinctive Service at (877) 337-3226. Do not attempt to repair the appliance yourself. If you need service, be sure to have the model and serial numbers available when you call.