1. Manuals
  2. Brands
  3. IDTECK Manuals
  4. Gateway
  5. Star RFL200C
  6. User manual

IDTECK Star RFL200C User Manual

Proximity access controller
Hide thumbs Also See for Star RFL200C:
Table of Contents

Advertisement

Quick Links

User's Manual
Proximity Access Controller

Advertisement

Table of Contents
loading

Related Manuals for IDTECK Star RFL200C

Summary of Contents for IDTECK Star RFL200C

  • Page 1 User’s Manual Proximity Access Controller...

  • Page 2: Table Of Contents

    Table of Contents 1. Important Safety Instructions ..............3 2. General ......................3 3. Features ......................4 4. Identifying Supplied Parts ................4 5. Specification ....................5 6. Installation....................6 7. Color Coded & Wiring Table ............... 7 8. Wire Connection to Controller ..............7 11.

  • Page 3: Important Safety Instructions

    Proximity Single Door Access Controller which can be mounted to metal door frame (mullion) or to any flat wall surface. The Star RFL200C / iPASS IP-RFL200C is epoxy potted that ensure you a successful operation even in harsh environments.

  • Page 4: Features

    - Power Fail Safe or Power Fail Secure Locks Selectable - Solid Epoxy Potted - Waterproof - Warranty: Life Time - Compatible Software: STAR RFL200C 4. Identifying Supplied Parts Please unpack and check the contents of the box. Reader Module RFL200C / IP-RFL200C User’s Manual...

  • Page 5: Specification

    5. Specification Model RFL200C IP-RFL200C Dual 8bit Microprocessor Program 64KByte Flash ROM Memory Memory Data Memory 4KByte EEPROM User 512 Users Event Buffer 256 Event Buffers IDK50 / IMC125: IPK50: Up to 2 inch (5cm) Up to 2 inch (5cm) Passive Type Read Range IDC80 / IDC170:...

  • Page 6: Installation

    6. Installation 6-1. Drill one 0.5”(12.7mm) hole at the central of the RFL200C / IP-RFL200C on mullion or wall mount. Route the cable of reader module through the central hole. 6-2. Drill one 0.39"(10mm) in right horizontal and 1.74"(44.4mm) in upper vertical through the central hole.

  • Page 7: Color Coded & Wiring Table

    7. Color Coded & Wiring Table SIGNAL COLOR Main Power (+12V) Power Ground (GND) Black Aux In 1 Yellow Door Contact In Blue Exit Button In Green Alarm Out Purple Door Lock Out White RS485 (A) Gray RS485 (B) Orange Not Connect Brown * Please cut out tail connector before installation.
  • Page 8 8-1. Connecting a power supply - Connect +12V of power supply to Red wire. - Connect GND of power supply to Black wire. 8-2. Connecting a door lock - Connect (+) wire of door lock to +12V wire of power supply. - Connect (-) wire of door lock to white wire of reader module.
  • Page 9 RFL200C / 485 Converter IP-RFL200C 485(-) Orange wire 485(+) Gray wire 9. Network connection to the access controller You can install up to 255 Units of RFL200C / IP-RFL200C.as in the below figure. - Max. 255 units (Board ID : 1~255) can be installed in a loop. - Able to connect directly via RS485 or RS232 converter.
  • Page 10 Set up Hardware All parameters of Star RFL200C / iPASS IP-RFL200C are set by the application software. 10-1 Set up “System Address” and “Normal” or “Toggle Mode”. ① Choose “System Name” and “System Address” on drop down list. ② Click “Normal Mode” or “Toggle Mode”.
  • Page 11 INPUT CARD DATA EMPLOYEE INFORMATION 10-4 System Initialization StarRFL200C / iPASS IP-RFL200C is initialized by the software. SELECT RFL200C 10-5 LED Color Control The Star RFL200C / iPASS IP-RFL200C can change its LED color to red or green by the application software.

  • Page 12: Operation

    SELECT RFL200C LED COLOR SELECT ※ See “STAR RFL200C” software manual to set up hardware. 11. Operation 11-1. When the RFL200C / IP-RFL200C is powered on, ① All LEDs are lit red or green, then they flash on and off twice and then turn off.
  • Page 13 11.7 Besides the operations described above, users can register or delete cards using the STAR RFL200C software, as well. Using this software, you can also adjust or change “Normal Mode” / “Toggle Mode”, “Door Open Time” and “LED Color Control”. ※ Refer to the “STAR RFL200C” software manual for more information.

  • Page 14: Fcc Registration Information

    12. FCC Registration Information FCC REQUIREMENTS PART 15 Caution: Any changes or modifications in construction of this device which are not expressly approved by the responsible for compliance could void the user's authority to operate the equipment. NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions;...

  • Page 15: Warranty Policy And Limitation Of Liability

    This Warranty doesn’t apply: 1) to any product which has been dismantled without authorization of IDTECK or/and has a damaged or detached QC label on its back side; 2) to any losses, defects, or damages caused by improper testing, operation, installation, maintenance, modification, alteration, or adjustment;...

  • Page 16: How To Make Rma Request (After Sales Service)

    14. How to Make RMA Request (After Sales Service) To make the RMA request, the product must be initially registered on IDTECK webpage. Please attach the RMA request form on the product and send it to IDTECK RMA Center. Please follow the instructions below: 1.
  • Page 17 The specifications contained in this manual are subject to change without notice at any time. 5F, Ace Techno Tower B/D, 684-1, Deungchon-Dong, Gangseo-Gu, Seoul, 157-030, Korea Tel : +82-2-2659-0055 Fax : +82-2-2659-0086 E-mail : webmaster@idteck.com Mar. 2010 Copyright ©2008 IDTECK Co., Ltd.

This manual is also suitable for:

Ipass ip-rfl200c

Table of Contents