Roland VS-2480 User Manual page 7

4. Rotate the TIME/VALUE dial to switch the setting to
"OFF." The sounds on Track 9 are now not sent to the
MIX bus.
5. Hold down [SHIFT] and press
[MASTER EDIT (TR1-16)]. The display switches to the
Master Edit screen.
6. Press [F3 (OUTPUT)]. The display switches to the
Output Assign screen.
7. Press [
] [ ] [
"TRACK DIRECT OUT."
8. Rotate the TIME/VALUE dial to switch the setting to
"ON." The VS-2480 switches to Track Direct Out mode.
9. Press [
] [ ] [
"A.MULTI 1/2."
10. Rotate the TIME/VALUE dial to connect "A.MULTI
1/2" and "TR 9/10."
The sounds on Tracks 9 and 10 are output from ANALOG
OUTPUT 1 and 2.
11. Use the same process to assign "TR 11/12" to A.MULTI
3/4, "TR 13/14" to A.MULTI 5/6, and "TR 15/16" to
A.MULTI 7/8. The sounds on Tracks 11, 12, 13, 14, 15,
and 16 are output from ANALOG MULTI OUTPUT 3, 4,
5, 6, 7, and 8, respectively.
You can also make the Output Assign settings in the EZ
ROUTING Output Assign screen ([EZ ROUTING]→
[F3 (OUTPUT)].
12. Connect each output to the external effects.
Using the DIR path
The sounds recorded to Tracks 9–12 are output using AUX
A/B OUTPUT, external effects are added, and then the
sounds are recorded to Tracks 1–4.
Externally Outputting Tracks 9–12
1. Press [TR1-16 (MASTER EDIT)].
2. Press [CH EDIT] on Track Mixer Channel 9. The display
switches to the Channel View screen.
3. Press [
] [ ] [
"DIR 1."
4. Rotate the TIME/VALUE dial to switch "DIR 1" to "ON"
(highlighted).
] [ ] to move the cursor to
] [ ] to move the cursor to
] [ ] to move the cursor to
5. Press [
] [ ] [
"MIX."
6. Rotate the TIME/VALUE dial to switch the setting to
"OFF." The sounds on Track 9 are now not sent to the
MIX bus.
7. In the same way, turn on DIR 2 for Track 10, and DIR 3
for Track 11.
You can press [ENTER] with "DIR" at this point to show the
DIR usage status.
8. Hold down [SHIFT] and press
[MASTER EDIT (TR1-16)]. The display switches to the
Master Edit screen.
9. Set DIR 1–4. You can set the level and the point from
which the signals are sent from the channel (Pre/Pst).
10. Press [F3 (OUTPUT)]. The display switches to the
Output Assign screen.
11. Press [
] [ ] [
"AUX A L/R."
12. Rotate the TIME/VALUE dial to connect "AUX A L/R"
and "DIR 1/2."
The sounds on Tracks 9 and 10 are output from AUX A.
13. Use the same process to assign "DIR 3/4" to "AUX B
L/R." The sounds on Tracks 11 and 12 are output from
AUX B.
You can also make the Output Assign settings in the EZ
ROUTING Output Assign screen ([EZ ROUTING]→
[F3 (OUTPUT)].
14. Connect each output to the external effects.
Recording the Sounds Output
from the External Effects to the
Tracks
1. Connect the outputs of the external effects to ANALOG
INPUT 1–8 (if using track direct outs as mentioned
above).
2. Hold down [SHIFT] and press
[PATCH BAY (EZ ROUTING)]. The display switches to
the Patch Bay screen.
3. Press [
] [ ] [
"INPUT MIXER 1 2."
VS-2480 Q&A
] [ ] to move the cursor to
] [ ] to move the cursor to
] [ ] to move the cursor to
7