Advertisement
<HF Damp>
Delay
HF Damp
—
200/250/315/400/500/
630/800/1000/1250/1600/2000/2500/3150/4000/5000/6300/
8000
(200
Hz
to
8
kHz),
BYPASS
This
sets
tlie
frequency
at
which
the
Wgh-frequency
compo-
nents
of the
reverb
sound
are cut
off.
The
degree
to
which
the
high-frequency
components
of a
reverb
sound
are
attenuated
depends on
the
composition
of
surrounding
walls.
HF Damp
(high-frequency
damp)
is
a
parameter
which
simulates
this
by
attenuating
the high-fre-
quency components.
A
lower
cutoff
frequency
results in a
sedate sound,
and
a
higher frequency produces
a
brighter
sound.
When
set to
"BYPASS," no
high-frequency
components
are cut
off.
*<Delay
Balanco
Delay
Balance
—
D100:OE
to
D0:10OE
This
sets
the
balance
for
the levels of the flanger
sound and
the flanger
-i-
delayed sound.
A
setting of
"D100:0E"
outputs
only
the flanger
sound,
and
a setting
of
"DO:100E" outputs
flanger
+
delayed sound.
<Level> Output
Level
—
to
127
This
sets
the overall
level for
the
effect
sound.
37:
CHORUS
->
FLANGER
This type connects
the
Chorus and
Flanger
in
series.
L-^
»-
<Cho
Dly>
Chorus
Predelay
—
ms
to
100
ms
This
sets
the
interval
from
the
time
when
the
original
sound
is
played
until
the
time
when
the
chorus
sound
is
played.
to 4.9
ms:
In 0.1
ms
steps
5.0 to 9.5
ms:
In
0.5
ms
steps
10
to
49 ms:
In
1
ms
steps
50
to
100 ms:
In 2
ms
steps
<ChoRate>
Chorus
Rate
—
0.05
Hz
to
10.0
Hz
This
sets
the cycle
for the
chorus
sound
undulations.
0.05
to
4.95
Hz:
In 0.05
Hz
steps
5.0 to 6.9
Hz:
In
0.1
Hz
steps
7.0 to 10.0
Hz:
In
0.5
Hz
steps
<Cho Dpt>
Chorus Depth
—
to
127
Tliis
sets
the
depth
of the
undulations
of the
chorus sound.
»<Cho
Bal>
Chorus
Balance
—
D100:0E
to
D0:100E
This
sets
the
balance
for the levels
of the original
sound and
the
chorus sound.
A
setting of
"D100:0E" outputs
only
the
original
sound,
and
a setting
of
"D0:100E" outputs chorus
sound
only.
<Flg
Dly>
Flanger Predelay
—
ms
to
100
ms
Tliis
sets
die interval
from
the
time
when
the
original
sound
is
played
until
the
time
when
the flanger
sound
is
played.
to
4.9
ms:
5.0 to 9.5
ms:
10
to
49 ms:
50
to
100 ms:
In
0.1
ms
steps
In 0.5
ms
steps
In
1
ms
steps
In 2
ms
steps
-
0.05
Hz
to 10.0
Hz
<FlgRate>
Flanger Rate
This
sets
the cycle for the flanger
undulations,
0.05
to
4.95
Hz:
In 0.05
Hz
steps
5.0 to 6.9
Hz:
In
0.1
Hz
steps
7.0 to
1
0.0
Hz:
In 0.5
Hz
steps
<Flg
Dpt>
Flanger
Depth
—
to
127
This
sets
the
depth
of the flanger undulations.
<Flg
Fbk>
Flanger
Feedback
—
-98%
to
+98%
This
sets
the
amount
of
feedback
for
the flanger
sound.
"Feedback"
refers
to
returning
a
portion
of the
output
signal
to
the
input
signal.
This
sets
the
percentage
of the
in-phase
or
inverted-phase output
signal (positive or
negative value)
that
is
returned
to
the input.
You
can
set a
value
from -98%
to
+98%,
in
steps of
2%.
No
feedback
is
applied
when
tliis
is
set to zero.
*<Flanger Balance> Flanger Balance
—
D100:0E
to
D0:100E
This
sets
the
balance
for the levels of the
chorus
sound and
the
chorus
+
flanger
sound.
A
setting of
"D100:0E"
outputs
only
the
chorus sound,
and
a
setting of
"D0:100E" outputs
chorus +
flanger
sound.
<Level>
Output
Level
—
to
127
This
sets
the overall
level for
the
effect
sound.
38:
CHORUS/DELAY
This
tjqje
connects
the
Chorus and
Delay
in parallel.
L-
^
__
Chorus
Delay
tX
The parameters
that
you
cart
set are the
same
as for
"CHO-
RUS
->
DELAY."
However,
the
Delay Balance
setting deter-
mines
the
balance
level
for
the original
sound
and
the
delayed
sound.
39:
FLANGER/DELAY
This type connects the Flanger
and
Delay
in parallel.
L
-
Flanger
Delay
The parameters
that
you can
set
are the
same
as for
"FLANGER
->
DELAY."
However,
the
Delay Balance
setting
determines
the
balance
level
for
the original
sound and
the
delayed sound.
40:
CHORUS/FLANGER
This type connects the
Chorus and
Flanger
in
parallel.
L
1;;^
Chorus
Flanger
The parameters
that
you
can
set are the
same
as
for
"CHO-
RUS
->
FLANGER."
Hoivever,
the
Flanger
Balance
setting
determines
the
balance
level
for
the original
sound and
the
flanger sound.
99
Advertisement
