Stanley GR29 User Manual
Underwater hydraulic grinder
Hide thumbs
Also See for GR29:
- User manual (20 pages) ,
- User manual (12 pages) ,
- Safety, operation & maintenance (16 pages)
Related Manuals for Stanley GR29
Summary of Contents for Stanley GR29
- Page 1 GR29 UNDERWATER HYDRAULIC GRINDER USER MANUAL Safety, Operation and Maintenance © 2014 Stanley Black & Decker, Inc. New Britain, CT 06053 U.S.A. 66486 7/2014 Ver. 7...
-
Page 2: Declaration Of Conformity
Provisiones especiales: Disposizioni speciali: Representative in the Union: Patrick Vervier, Stanley Dubuis 17-19, rue Jules Berthonneau-BP 3406 41034 Blois Cedex, France. Vertreter in der Union/Représentant dans l’union/Representante en la Union/Rappresentante presso l’Unione Done at/Ort/Fait à/Dado en/Fatto a Stanley Hydraulic Tools, Milwaukie, Oregon USA... -
Page 3: Table Of Contents
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest authorized and certified dealer, call Stanley Hydraulic Tools at the number listed on the back of this manual and ask for a Customer Service Representative. -
Page 4: Safety Symbols
Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. 4 ► GR29 User Manual... -
Page 5: Safety Precautions
Hold the shaft with a second wrench on the the flats The GR29 Hydraulic Grinder will provide safe and de- behind the wheel and tighten securely. pendable service if operated in accordance with the in- •... - Page 6 Do not allow other persons near the tool when start- ing or cutting. • Any use of this tool outside those stated in this man- ual are forbidden. • Never operate the tool when you are tired or fa- tigued. 6 ► GR29 User Manual...
-
Page 7: Tool Stickers & Tags
TAG TO BE REMOVED ONLY BY TAG TO BE REMOVED ONLY BY TOOL OPERATOR. TOOL OPERATOR. SEE OTHER SIDE SEE OTHER SIDE SAFETY TAG P/N 15875 (shown smaller then actual size) GR29 User Manual ◄ 7... -
Page 8: Hose Types
HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS. -
Page 9: Hose Recommendations
HOSE RECOMMENDATIONS GR29 User Manual ◄ 9... -
Page 10: Htma Requirements
2000 psi 2000 psi 2000 psi (at the power supply outlet) (172 bar) (138 bar) (138 bar) (138 bar) (138 bar) NOTE: These are general hydraulic system requirements. See tool specification page for tool specific requirements 10 ► GR29 User Manual... -
Page 11: Operation
Tighten the nut securely by using two open-end wrenches, one wrench on the flats of the spindle shaft, the other wrench on the jam nut. 4. Remove the grinding wheel by loosening the jam nut as in Step 3. GR29 User Manual ◄ 11... - Page 12 OPERATION TOOL OPERATION COLD WEATHER OPERATION For best results, use only Stanley approved accesso- If the grinder is to be used during cold weather, preheat ries. They have been designed and selected to get the the hydraulic fluid at low engine speed. When using the most from the tool.
-
Page 13: Tool Protection & Care
This can cause damage to internal seals. • Always replace hoses, couplings and other parts with replacement parts recommended by Stanley Hydraulic Tools. Supply hoses must have a mini- mum working pressure rating of 2500 psi/172 bar. GR29 User Manual ◄ 13... -
Page 14: Troubleshooting
Porting spool incorrectly assembled. Refer to Service Manual. stop after trigger is released. Check valve in trigger spool not func- Replace trigger spool assembly. tioning correctly. Check valve not serviceable. Mechanical failure. Disassemble tool and inspect for damage. 14 ► GR29 User Manual... -
Page 15: Accessories
Grinding Wheel for Metal 9 in. Diameter × 5/8 in. -11 THD Arbor ..............02587 Grinding Wheel for Masonry 9 in. Diameter × 5/8 in. -11 THD Arbor ..............02588 Grinding Wheel 7 in. × 5/8 in. -11 THD Arbor ....................03691 Depressed Center Wheel Adapter ........................05194 GR29 User Manual ◄ 15... -
Page 16: Gr29 Parts Illustration
GR29 PARTS ILLUSTRATION 16 ► GR29 User Manual... -
Page 17: Gr29 Parts List
RETAINING RING 00149 O-RING 13791 SPINDLE SHAFT 13828 WOODRUFF KEY 07987 BACK-UP WASHER 09396 BACK-UP RING 08017 O-RING 12286 MAIN HOUSING 09275 RETAINING RING 07991 IDLER SHAFT 08014 BUSHING 13783 DRIVE GEAR 08023 O-RING 07978 BUSHING GR29 User Manual ◄ 17... -
Page 18: Underwater Tools Depth Guideline
ROV operation is still limited to the tool, for Depth (ft) 8 GPM 12 GPM example a percussive tool has the same depth 5/8” 5/8” limitation whether ROV or diver operated. 3/4” 1” 1” 1” 1000 1” 1-1/4” 18 ► GR29 User Manual... - Page 19 NOTES GR29 User Manual ◄ 19...
- Page 20 Stanley Hydraulic Tools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www.stanleyhydraulics.com...
Need help?
Do you have a question about the GR29 and is the answer not in the manual?
Questions and answers