Table of Contents
Advertisement
Available languages
Available languages
f Impairment of hearing.
f Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
USING AN EXTENSION CABLE
If it is necessary to use an extension cable, please used
an approved extension cable that fits the tool's power input
specifications (please refer to the technical data). The
minimum cross- sectional area of the conducting wire is
1.5 sq. mm. Cables should be untangled before reeling up.
Please refer to the following table.
Conductor size (mm2)
0.75
1.00
1.50
2.50
4.00
Voltage
Amperes
115
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
230
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
ASSEMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Attaching the Side Handle (Fig. E)
Warning! When drilling holes in concrete or bricks,
please use the side handle for your safety.
f Turn the grip counterclockwise until you can slide the
side handle onto the front of the tool.
f Rotate the side handle into the desired position.
f Tighten the side handle by turning the grip clockwise.
f
Warning! When using the tool, remember to install the
side handles properly.
Fitting an accessory (Fig. A)
f Clean and grease the shank (7) of the accessory.
f Insert the accessory bar into the tool clamp (4).
f Push the accessory down and turn it slightly until it fits
into the slots.
Cable rating
(Amperes)
6
10
15
20
25
Cable length (m)
7.5 15 25 30 45 60
Cable rating (Amperes)
6
6
6
6
6 10
6
6
6
6
15 15
6
6
10 15 20 20
10
10 15 20 20 25
15
15 20 25 25 -
20
20 25 -
-
-
6
6
6
6
6 6
6
6
6
6
6 6
6
6
6
6
10 15
10
10 10 10 15 15
15
15 15 15 20 20
20
20 20 20 25 -
f Pull on the accessory to check if it is properly locked.
The hammering function requires the accessory to be
able to move axially several centimetres when locked
in the tool clamp.
f To remove the accessory, pull back the sleeve (8) and
pull out the accessory tool clamp.
USE
Warning! Please operate tool with normal load. Do not
over- load.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the operating mode (Fig. B)
The tool can be used in two operating modes. Based on
actual work requirements, the drilling mode selector (3)
can be rotated to the required position.
Hole Drilling (Fig. B and F)
f For drilling in steel, wood and plastics, set the
operating mode selector (3) to the position . At the
same time, it is necessary to use a suitable drill chuck
(13) (optional accessory) to clamp the attachment rod.
f Insert the drill chuck (13) into the tool chuck
(4) according to the instructions for installing
attachments. Turn the drill chuck to loosen the
clamps at the front-end of the drill clamp, and insert
the accessory bar (14) into the clamps and turn the
chuck in the opposite direction. You may also use the
drill chuck key to tighten the clamp.
Hammer Drilling (Fig. B)
f For hammer drilling in masonry and concrete, set the
operating mode selector (3) to the position
f The drill bit has to be placed accurately onto the drill
hole position. After that, pull the switch for optimal
effects. Make sure the tool is in the correct position to
prevent the drill from deviating from the hole.
f When the drill hole is clogged with debris or fine
powder, please don't exert any more pressure. Tool
should be put in free-running state before removing
part of the drill bit from the hole. If repeated a few
times, the blockage in the hole would be cleared, and
normal drilling can resume.
Warning! When the drill bit hits cement or the steel
rebar in the cement, the tool may recoil dangerously.
Please hold the tool tightly in a balanced and stable
position at all times to prevent it from recoiling
dangerously.
Overload coupling device
If the drill bit his caught or hooked, the driving force
transmitted to the drill shaft will be cut off. This would
ENGLISH • 15
..
Advertisement
Table of Contents
