Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zeagle 1BCD
Summary of Contents for Zeagle 1BCD
-
Page 1: Buoyancy Compensator
Systems, Inc. Buoyancy Compensator Owner’s Manual... -
Page 2: Introduction
We value your decision to invest in a Zeagle Buoyancy Control System. Please have your authorized Zeagle Dealer familiarize you with the operation and care of your new Zeagle Buoyancy Compensator* (BC) and go over your Owner’s Manual with you. Have your Dealer sign the appropriate line on the service record at the end of this manual, after he has performed this service. -
Page 3: Table Of Contents
Contents Introduction ................1 Warranty Information ............3 General Information and Specifications ....... 4 Function of the Zeagle System ..........7 Fitting and Assembly ............9 Pre-dive Assembly and Inspection ........15 Donning Procedures ............. 19 Diving with the Zeagle System ..........20 Emergency Procedures ............ -
Page 4: Warranty Information
Warranty Information Owner’s Responsibilities • Zeagle Systems, Inc. requires that the end user of this system be certified by a nationally or internationally recognized SCUBA certification agency and adequately trained in its use by a certified SCUBA instructor with thorough knowledge and experience in the use of Zeagle Systems, Inc. -
Page 5: General Information And Specifications
General Information and Specifications This Buoyancy Compensators Owner's Manual contains important safety, maintenance, and operation information. Read this manual thoroughly before diving. Important information on the assembly, operation, and maintenance of your BC is designated throughout this manual with the 'IMPORTANT' graphic and symbol above. - Page 6 SCUBA Cylinder Selection and Configuration Your buoyancy depends on the combination of all your diving equipment added to your own buoyancy. The Zeagle System is designed to work with a variety of tank sizes and configurations. Failure to comply with the following information may result in an improper buoyancy configuration.
- Page 7 General Information and Specifications Surface Buoyancy of BC's Your BC's buoyancy, has been rated by Zeagle Systems, Inc. Buoyancy figures were measured in fresh water at sea level, and were rounded down to the nearest pound. For buoyancies listed in the metric system, buoyancy is measured in multiples of 10 Newtons, then rounded down to the next lowest multiple.
-
Page 8: Function Of The Zeagle System
Function of the Zeagle System The Zeagle Buoyancy Control System The function of the Zeagle buoyancy control system is to add to your diving enjoyment. It is designed to provide you with a comfortable way of “wearing” your SCUBA system, a resting platform while on the surface, and an easy means of controlling your buoyancy while diving. - Page 9 Function of the Zeagle System Bladder Assembly There are three basic bladder assemblies used on Zeagle BC’s. The bladder assembly attaches to the vest section via two straps which slide through the webbing at the back of the vest under the tank bands (see cylinder band illustration on pages 10 &...
-
Page 10: Fitting And Assembly
Fitting and Assembly Adjusting Side Panels 1.Using two coins, unscrew the plastic screw fasteners. 2.Move the side panel to different set of grommets on vest and reinstall. 1999 1999... - Page 11 Fitting and Assembly Threading The Standard Single Cylinder System Non-Slip Plate Illustration “A” (Single Cylinder Band Assembly) Illustration “B” (Standard System Only) 1. Thread cylinder band through non-slip plate and then under the bottom center backplate straps as shown in Illustration “A.” 2.
- Page 12 Fitting and Assembly Threading The Standard & Quick Release System On A Twin Cylinder Back Plate Standard System Quick Release System Optional Band Extension Back Plate Grommets • An alternate method of attaching twin cylinders with steel bands is by bolting through the back plate grommets.
- Page 13 Fitting and Assembly Threading The Quick Release System For A Single Cylinder On Twin Cylinder Back Plate...
- Page 14 Fitting and Assembly Scout Single Cylinder Band System Quick Release fully closed...
- Page 15 Fitting and Assembly Proper Fit The Zeagle System allows the diver to size each component of the buoyancy system independently for a true custom fit. For proper performance please be sure that your system fits as described below. Put BC on (before attaching to SCUBA cylinder) and adjust shoulders and waist as follows.
-
Page 16: Pre-Dive Assembly And Inspection
Pre-dive Assembly and Inspection Adjust the BC so that it does not restrict your breathing. Restriction of normal breathing while wearing your BC could result in injury or death. Before each dive, check all bands, straps, clips, and/or waist panels for proper adjustment. Over Pressure (OP Valve)/ Dump Valve The over pressure/ dump valve is typically located on the lower front of the bladder assembly. - Page 17 Pre-dive Assembly and Inspection Weight System Inspection Check to see that weight release system is secure. Ripcord ™ release system - check bottom of weight pockets to be sure they are held closed by the ripcord. If the Ripcord has been pulled, rethread the system. (Refer to the rethreading section on following page).
- Page 18 Pre-dive Assembly and Inspection Check to see that weight release system is secure. Trim Weight™, Pull-Out Pocket ™ Touch Fastener System - Check to see that the touch fastener material flap on the bottom and sides of each weight pocket completely overlaps and is secure.
- Page 19 Pre-dive Assembly and Inspection Loading the Zeagle Integrated Weight System: Loading: Weights can be loaded after the system is donned as shown or the weights can be loaded before the system is donned. Considerations include the amount of weight and the distance to enter the water. Ask your buddy for help in either case.
-
Page 20: Donning Procedures
• Be sure you are familiar with the low pressure inflator system on your Zeagle BC. Inflate the system and check for leakage. • Weights can be installed in the weight pockets before the BC is donned or after. -
Page 21: Diving With The Zeagle System
SYSTEM. Let out just enough air to start your descent. As you descend and when you reach your desired depth you will need to add air to your Zeagle BC by pressing on the air inlet button of your low pressure inflator to attain “neutral” buoyancy. -
Page 22: Emergency Procedures
Emergency Procedures Emergency Weight Release If you are diving with a buoyant wet or drysuit, be aware that releasing weights at depth should only be done if absolutely necessary (for example, if your drysuit has flooded, making you extremely negative). Without weights, it may be very difficult to control your ascent rate as you near the surface. - Page 23 Above based on recreational no decompression diving. Decompression divers must have complete redundant systems to handle all problems underwater. If at any time abnormal performance or malfunction is experienced, the system must be serviced by an authorized Zeagle Dealer prior to any further use.
-
Page 24: Maintenance
Store partially inflated in a cool dry place. Inspection and Service Interval Your BC should be inspected and maintained by an Authorized Zeagle Dealer at least once a year, and more often if you dive frequently. This is a required action to keep your warranty in effect. -
Page 25: Service Record
Service Record SERVICE RECORD SERVICE PERFORMED SERVICE CENTER TECHNICIAN # DATE Dealer Preparation Owner Orientation... -
Page 26: Locating Service And Support
Service Notes: Locating Service and Support The Dealer that sold you your Buoyancy Compensator will be able to assist you with additional questions regarding product operation, warranty, and service. Your Local Zeagle Dealer: (Dealer to affix stamp here) - Page 27 Zeagle Systems, Inc. 37150 Chancey Road Zephyrhills, FL. 33541 Phone: (813) 782-5568 Fax: (813) 782-5569 www.zeagle.com FOR THOSE PRODUCTS BEARING THE MARK: EC Type Examination by: SGS Yarsley International Certification Services Ltd. SGS House, Portland Road East Grinstead RH19 4 ET England...