Makita LW1400 Instruction Manual
  1. Manuals
  2. Brands
  3. Makita Manuals
  4. Saw
  5. LW1400
  6. Instruction manual

Makita LW1400 Instruction Manual

Portable cut-off
Hide thumbs Also See for LW1400:
Table of Contents

Advertisement

Quick Links

See also: Technical Information , Instruction Manual
INSTRUCTION MANUAL
Portable Cut-Off
LW1400
LW1401
DOUBLE INSULATION
Read before use.

Advertisement

Table of Contents
loading

Related Manuals for Makita LW1400

Summary of Contents for Makita LW1400

  • Page 1 INSTRUCTION MANUAL Portable Cut-Off LW1400 LW1401 DOUBLE INSULATION Read before use.

  • Page 2: Specifications

    SPECIFICATIONS Model: LW1400 LW1401 Wheel diameter 355 mm Hole diameter 25.4 mm No load speed 3,800 min Dimensions With European type safety 530 mm x 295 mm x 640 mm 500 mm x 295 mm x 640 mm (L x W x H)

  • Page 3: Additional Safety Rules For Tool

    When operating a power tool outdoors, use an Maintain power tools. Check for misalignment extension cord suitable for outdoor use. Use of or binding of moving parts, breakage of parts a cord suitable for outdoor use reduces the risk of and any other condition that may affect the electric shock.

  • Page 4: Functional Description

    If it should when not in use or carrying. become necessary to clear dust, first discon- For LW1400 nect the tool from the mains supply (use non To unlock, depress the tool head slightly and push the metallic objects) and avoid damaging internal lock pin.

  • Page 5: Cutting Angle Adjustment

    For LW1400 Loosen the screw on the guide plate. Move the guide plate to the desired position then tighten the screw. ► 1 . Lock button / Lock-off button 2. Switch trigger For tool with lock button To start the tool, simply pull the switch trigger. Release the switch trigger to stop.
  • Page 6 Spark guard adjustment For LW1401 only (country specific) ► 1 . Guide plate 2. Lever For LW1401 NOTICE: When performing right miter cut, ► 1 . Screw 2. Spark guard always set the guide plate at 0 - 170 mm position. Setting at the 35 - 205 mm or 70 - 240 mm position The spark guard is factory-installed with its lower edge hinders the movement of stopper plate, which...
  • Page 7 ► 1 . Clamping screw ► 1 . Inner flange 2. Ring 3. O-ring 4. Cut-off wheel 5. Outer flange 6. Toolless clamp / Hex bolt For LW1400 Raise the safety guard. Turn the toolless clamp coun- terclockwise while holding down the shaft lock. Then remove the toolless clamp, outer flange and cut-off wheel.

  • Page 8: Cutting Capacity

    Cutting capacity Maximum cutting capacity varies depending on the cutting angle and workpiece shape. Max. cutting capacity with a brand-new cut-off wheel Cutting angle / 90° 45° Workpiece shape 127 mm 127 mm ► 1 . Shaft lock 2. Toolless clamp 115 x 130 mm 115 x 103 mm To install the cut-off wheel, follow the removal proce-...

  • Page 9: Carrying Tool

    ► 1 . Spacer block ► 1 . Vise plate 2. Workpiece diameter 3. Guide plate 4. Spacer block width When cutting workpieces over 85 mm wide at an angle, attach a straight piece of wood (spacer) over 190 mm Long workpieces must be supported by blocks on long x 45 mm wide to the guide plate as shown in the either side so that it will be level with the base top.

  • Page 10: Replacing Carbon Brushes

    ► 1 . Brush holder cap OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
  • Page 12 Makita Corporation 885456-6 20150819 www.makita.com...

This manual is also suitable for:

Lw1401

Table of Contents